MATRIX U50 R50 Recumbent Bike User Manual

U50 R50 Recumbent Bike
User Manual

ASSEMBLY

WARNING!
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the equipment could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the equipment, the assembly instructions must be reviewed and corrective actions should be taken.
SERIAL NUMBER LOCATION Before proceeding, find your equipment’s serial number located on a barcode sticker and enter it in the space provided below.
SERIAL NUMBER
MODEL NAME

• F R30

• R50

• F U30
  MATRIX EXERCISE BIKE

• F U50

UNPACKING
Unpack the equipment where you will be using it. Place the carton on a level flat surface. It is recommended that you place a protective covering on your floor. Never open box when it is on its side.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded.
Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe this off. If you have difficulty, a light application of lithium grease is recommended.
TOOLS INCLUDED:

• Phillips Screwdriver
• R30/R50: 6 mm Hex Wrench, 5 mm Hex Wrench, 4 mm Hex Wrench
• U30/U50: 5 mm Hex Wrench, 4 mm Hex Wrench, 2.5 mm Hex Wrench, 8 mm Wrench

R30 / R50 PARTS INCLUDED:

• 1 Bike Frame
• 1 Console Mast
• 1 Handlebars
• 1 Top Cap Front Cover
•  1 Top Cap Rear Cover
• 1 Seat Frame Assembly
•  1 Seat Bottom
• 1 Water Bottle Holder
• 1 Mesh Seatback
• 1 Outside Cover (R30 only)
• 1 Inside Cover (R30 only)
• 1 Power Cord
• 1 Hardware Kit
• Console sold separately

U30 / U50 PARTS INCLUDED:

• 1 Bike Frame
• 1 Seat
• 2 Console Mast
• 1 Console Bridge
• 1 Console Bridge Cover
• 1 Handlebar
•  1 Handlebar Bracket
• 1 Bike Seat Bracket
• 1 Water Bottle Holder
• 1 Console Back Cover
• 2 Pedals
• 1 Power Cord
• 1 Hardware Kit
  Console sold separately

NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the information card. A Open HARDWARE FOR STEP 1.
B Carefully pull the CABLES (1) through the CONSOLE MAST (2) using the LEAD WIRE (3) located inside the CONSOLE MAST
(2). Discard the lead wire.
C Attach the CONSOLE MAST (2) to MAIN FRAME (4) using 4 BOLTS (A) and 4 SPRING WASHERS (B). Torque settings: 23.1 Nm / 17 lb-ft.
Note: Be careful not to pinch any wires while attaching the console mast.
Hardware For Step 1

A Open HARDWARE FOR STEP 2.
B Slide TOP CAP REAR COVER (5) over CONSOLE MAST (2) and snap into place.
C Slide TOP CAP FRONT COVER (6) over CONSOLE MAST (2) and snap into place
D Attach HANDLEBARS (7) to CONSOLE MAST (2) using 2 BOLTS (C) and 2 SPRING WASHERS (B). Torque settings: 23.1 Nm / 17 lb-ft.
Hardware For Step 2

| Description| R30| R50
---|---|---|---
C| Bolt| 2| 6
B| Spring Washer| 2| 6
L| Flat Washer| 0| 4

A Open HARDWARE FOR STEP 3
B Attach the WATER BOTTLE HOLDER (8) to the SEAT FRAME ASSEMBLY (9) using 2 SCREWS (D).
C Attach the SEAT FRAME ASSEMBLY (9) to the SEAT SLIDE (10) using 4 BOLTS (E) and 4 SPRING WASHERS (F). Torque settings: 23.1 Nm / 17 lb-ft.
D Connect the CABLES (11).
Note: Be careful not to pinch any wires while attaching the seat frame.
Hardware For Step 3

| Description| Qty
---|---|---
D| Screw| 2
E| Bolt| 4
F| Spring Washer| 4

A Open HARDWARE FOR STEP 4
B Attach the SEAT BOTTOM (12) to the SEAT FRAME ASSEMBLY (9) using 4 BOLTS (G) and 4 SPRING WASHERS (H). Torque settings: 9.5 Nm / 7 lb-ft.
Hardware For Step 4

| Description| Qty
---|---|---
G| Bolt| 4
H| Spring Washer| 4

NOTE: This step is for R30 models only.
A Open HARDWARE FOR STEP 5.
B Place the INSIDE COVER (13) over the MESH SEAT BACK (14) and mount the MESH SEAT BACK (14) to the SEAT FRAME
ASSEMBLY (9) with 4 BOLTS (C) and 4 SPRING WASHERS (I). Torque settings: 23.1 Nm / 17 lb-ft.
C Attach the OUTSIDE COVER (15) to the SEAT FRAME (9) and INSIDE COVER (13) with 3 SCREWS (J).
Hardware For Step 5

| Description| Qty
---|---|---
C| Bolt| 4
I| Spring Washer| 4
J| Screw| 3

NOTE: This step is for R50 models only.
A Open HARDWARE FOR STEP 5.
B Attach the MESH SEAT BACK (14) to the SEAT FRAME ASSEMBLY (9) using 6 BOLTS (I). Torque settings: 9.5 Nm / 7 lb-ft.
Hardware For Step 5

| Description| Qty
---|---|---
I| Bolt| 6

A Open HARDWARE FOR STEP 6.
B Connect the CABLES (1) to the CONSOLE (17) and carefully tuck the excess cable into the CONSOLE MAST (2).
C Attach the CONSOLE (17) to the CONSOLE MAST (2) using 4 BOLTS (K).
Note: Be careful not to pinch any wires while attaching the console.
Hardware For Step 6

| Description| Qty
---|---|---
K| Bolt| 4

R30 / R50 ASSEMBLY COMPLETE!
SEAT ADJUSTMENT
To determine proper seat position, sit on the seat and position the ball of your foot on the center of the pedal. Your knee should bend slightly at the furthest pedal position. You should be able to pedal without locking your knees or shifting your weight from side to side.
NOTE: It is recommended that you do not sit on the seat while adjusting its position. SEAT POSITION
To adjust, lift up on the adjustment lever and hold. Then, slide the seat to a position that puts you in a comfortable pedaling range (one that keeps a slight bend in your knee while your legs are in the extended position). Release lever to lock the mechanism.  SEAT BACK ADJUSTMENT (R50)
To adjust the tilt angle of the seat back, rotate the lever down (counterclockwise) and lean back on the mesh seat back until the desired position is achieved. When the position is set, rotate the lever upward (clockwise) until it is snug. The seat back comes equipped
with a spring return system to return the seat back to its original position when the adjustment lever is released and the user is not leaning against the seat back.A Open HARDWARE FOR STEP 1.
B Attach the SEAT (1) to the SEAT POST (2) using SEAT BRACKET (3) and 2 BOLTS (A). Torque settings: 9.5 Nm / 7 lb-ft.
Note: Tighten the bolts evenly by alternating between front and back until completely tightened.
Hardware For Step 1

| Description| Qty
---|---|---
A| Bolt| 2

A Open HARDWARE FOR STEP 2.
B Carefully pull the CABLES (4) through the RIGHT CONSOLE MAST (6) using the LEAD WIRE (5) located inside the CONSOLE MAST (6). Discard the lead wire.
C Attach the RIGHT CONSOLE MAST (6) to BIKE FRAME (8) using 5 BOLTS (B).
D Attach the LEFT CONSOLE MAST (7) to BIKE FRAME (8) using 5 BOLTS (B). Leave bolts loose until after step 3.
Note: Be careful not to pinch any wires while attaching the console mast.
Hardware For Step 2

| Description| Qty
---|---|---
B| Bolt| 10

A Open HARDWARE FOR STEP 3.
B Carefully feed the CABLES (4) under the CONSOLE BRIDGE (9).
C Attach CONSOLE BRIDGE (9) to the CONSOLE MASTS (6 & 7) using 8 BOLTS (B). Torque settings: 23.1 Nm / 17 lb-ft.
D Attach the WATER BOTTLE HOLDER (10) to the CONSOLE MASTS (6 & 7) using 4 SCREWS (C).
Hardware For Step 3

| Description| Qty
---|---|---
B| Bolt| 8
C| Screw| 4

A Open HARDWARE FOR STEP 4.
B Carefully feed the CABLES (11) through the HANDLEBAR BRACKET (13).
C Attach the HANDLEBAR (12) to the HANDLEBAR BRACKET (13) using 4 BOLTS (D) and 4 NUTS (E).
D Snap CONSOLE BRIDGE COVER (14) into position.
E Carefully feed the CABLES (11) through the CONSOLE BRIDGE (9).
F Attach the HANDLEBAR BRACKET (13) to the CONSOLE BRIDGE (9) using 4 BOLTS (F).
Hardware For Step 4

| Description| Qty
---|---|---
D| Bolt (20mm)| 4
E| Nut| 4
F| Bolt (12mm)| 4

A Open HARDWARE FOR STEP 5.
B Connect the CABLES (11) to the CONSOLE (15) and carefully tuck them into the CONSOLE BRIDGE (9).
C Attach the CONSOLE (15) to the CONSOLE BRIDGE (9) using 4 BOLTS (G).
D Attach the CONSOLE BACK COVER (16) to the console (15) and CONSOLE BRIDGE (9) using 6 SCREWS (H).
Hardware For Step 5

| Description| Qty
---|---|---
G| Screw| 4
H| Screw| 6

A Attach the RIGHT PEDAL to the RIGHT CRANK ARM, tightening it clockwise with the provided 13mm/15mm flat wrench.
B Attach the LEFT PEDAL onto the left crank arm, tightening it counter- clockwise with the provided 13mm/15mm flat wrench.
(NOTE: The left crank arm is reversed threaded so it is very important that it is tightened counter-clockwise. Tightening it the opposite way can damage the pedal or the crank arm or both.)

SEAT ADJUSTMENT

To determine proper seat position, sit on the seat and position the ball of your foot on the center of the pedal. Your knee should bend slightly at the furthest pedal position. You should be able to pedal without locking your knees or shifting your weight from side to side.
NOTE: It is recommended that you do not sit on the seat while adjusting its position. To adjust, loosen the adjustment knob by turning it two half turns counterclockwise. Pull out the knob to unlock the post, and adjust the post up or down to the desired setting. Release the knob to lock in place. Turn the knob clockwise until tightened. Please check to be sure seat post is locked in place before each use. To adjust, lift up on the adjustment lever and hold while sliding the post up or down to the desired setting. Release the lever to lock in place. Please check to be sure seat post is locked in place before each use. HANDLEBAR POSITION
To adjust, rotate the adjustment lever down and slide the handlebar set to a position that puts the handlebars within comfortable reach. Lock the mechanism by lifting up on the adjustment lever until tight.

© 2021 Johnson Health Tech
Rev 1.1 B

Documents / Resources

| MATRIX U50 R50 Recumbent Bike [pdf] User Manual
U50 R50 Recumbent Bike, U50, R50 Recumbent Bike, Recumbent Bike, Bike
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>