newair Evaporative Air Cooler Owner’s Manual

: June 6, 2024
: NewAir

newair Evaporative Air Cooler

SPECIFICATIONS

M ODEL N O :	NEC500SI00
P RODUCT D IMENSIONS :	16.1″ W x 11.1″ D x 35.0″ H
P RODUCT W EIGHT :	16.1 Pounds
V OLTAGE :	120V
W ATTAGE :	110W
C OVERAGE A REA :	250 sq. ft.
T ANK S IZE	1.45 Gallons
F AN S PEEDS :	3
N OISE L EVEL (D B ):	66
A IRFLOW :	470 CFM
O SCILLATION :	Yes
W ARRANTY :	1 Year Manufacturer’s Warranty

REGISTER YOUR PRODUCT ONLINE

Register Your NewAir Product Online Today!

Take advantage of all the benefits product registration has to offer:

| Service and Support
Diagnose troubleshooting and service issues faster and more accurately
---|---
| Recall Notifications
Stay up to date for safety, system updates and recall notifications
| Special Promotions
Opt-in for NewAir promotions and offers

newair.com/register

Alternatively, we recommend you attach a copy of your sales receipt below and record the following information, located on the manufacturer’s nameplate on the rear of the unit. You will need this information if it becomes necessary to contact the manufacturer for service inquiries.

Date of Purchase: ___
Serial Number: ___
Model Number: ___

SAFETY INFORMATION & WARNINGS

| These instructions are not meant to cover every possible condition and situation that may occur. Please read all instructions before using this evaporative cooler. Failure to carefully read all instructions may result in possible electric shock or fire hazard, and will void the manufacturer’s warranty.
---|---

Use this evaporative cooler only as instructed in this owner’s manual. Other uses may cause electric shock, injury or fire.
Use this evaporative cooler only as instructed in this owner’s manual. Other uses may cause electric shock, injury or fire.
Close supervision is required if this cooler is used near children or pets.
To protect against electric shock, do not immerse this cooler or its plug and cord in water.
If the cooler is being transported or will not be in use, disconnect it from the power supply by tightly gripping the plug and pulling it from the power outlet. Do not disconnect the power supply by pulling on the evaporative cooler’s power cord.
Avoid contact with any of the evaporative cooler’s moving parts.
Place the evaporative cooler on a level surface.
This evaporative cooler is intended to plug into a matching receptacle. Under no circumstances should the plug be altered in any way. An improper connection can result in electric shock.
If possible, avoid using extension cords with this evaporative cooler. If an extension cord is absolutely necessary, do not use more than one extension cord to operate more than one cooler.
Do not insert objects or allow fingers to enter into the cooler’s grills, as this may cause electric shock or bodily injury. Do not block or tamper with the evaporative cooler while it is in operation.
Do not run the power cord under mats or carpeting, and do not cover the power cord with runners. Arrange the power cord away from room traffic and where it can be tripped over.
Do not operate this evaporative cooler in the presence of flammable substances or explosives.
Do not place the cooler near an open flame or cooking/heating appliances.
If the evaporative cooler will not be in use, empty the tank of any remaining water.
If the cooler’s plug or power cord is damaged, do not attempt to repair the components yourself. Please contact customer service or have the unit examined by an authorized service provider.

Safety Warnings and Precautions

WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
(a) The cells shall be disposed of properly, including keeping them away from children; and
(b) Even used cells may cause injury.

SAVE THESE INSTRUCTIONS

PARTS LIST

Check to insure the following parts are included with your product:

Evaporative cooler
Ice Pack
Remote control
CR2032 3V battery

Fan head
Display panel
Water level indicator
Caster
Control panel
Remote control storage slot
Carrying handles
Cooling pad knob
Cooling pad slot
Dustproof air filter
Water tank
Power cord bracket
Power cord
Water tank knob
Ice pack
Remote control

PRODUCT BENEFITS

Designed for cooling small to medium size bedrooms, living rooms, sunrooms, patios and offices
Sleek, modern design makes it an attractive addition to your home
High-efficiency, rigid cooling pad holds more water
Removable water tank makes refilling and emptying easy
Powerful motor results in more powerful airflow, faster evaporation and cooler air
Consumes about as much electricity as your typical 100 watt light bulb
Eco-friendly evaporative cooling system cools the air by the natural process of evaporating water with no Freon or harmful chemicals
Adds moisture to dry environments and eliminates airborne dust particles
Covers up to 250 square feet

OPERATING INSTRUCTIONS

SET UP

Carefully remove all packaging materials and retain for future storage/use. Make sure there is no residual foam left in any of the components. No tools will be required to assemble this evaporative cooler.

Place the cooler on a firm, level surface before proceeding. Before using the evaporative cooler for the first time, we recommend cleaning the tank with a solution of warm water and light detergent.

FILLING THE WATER TANK

Remove the water tank by turning the water tank knob counterclockwise 90 degrees.
Fill the tank with clean water. Pay attention to the water level indicator located on the front of the cooler to avoid overfilling the tank. The approximate tank size of the NEC500SI00 is 1.5 gallons (5.5 liters).
Replace the tank back onto the back of the unit. Turn the water tank knob clockwise 90°. This locks the water tank back into place.

USING THE ICE PACK

The NEC500SI00 evaporative cooler includes an optional ice pack for added cooling.

Place the ice pack in the freezer until frozen. Do not open the ice pack or ingest its contents.
Put the ice pack into one of the water tank’s chambers.
The ice pack is not necessary for operation, but will help enhance the cooling effect in higher temperatures.
The ice pack will last approximately 4 hours before melting.

THE CONTROLS & OPERATION

After the tank is filled with water, connect the evaporative cooler to a power outlet. The unit will beep twice, indicating that the power source is connected. The cooler will be in standby mode at this time.

ON/SPEED & OFF BUTTONS

Press the ON/SPEED button to turn on the evaporative cooler.
To adjust the fan speed, press ON/SPEED button again until your desired speed has been reached. The current fan speed will be indicated on the display panel. To turn the unit off and revert back to standby mode, press the OFF button.

Fan Speed Indicators:

COOLER/HUMIDIFIER BUTTON

| After the desired fan speed has been selected, press the COOLER/HUMIDIFIER button to activate the cooling/humidifying function. This powers the water pump, cools the air and adds moisture to your air at the same time. The blue cooling icon will also be visible on the display panel.
---|---

Please note that if the initial fan speed is set to 3, the unit will revert back to the second speed setting for 5 minutes. After 5 minutes, the unit will automatically switch to the third fan speed. This allows the cooling pad to absorb sufficient water for optimized cooling. The cooler will not revert back to other speeds if the initial fan speed was set to either 1 or 2.

MODE BUTTON

The NEC500SI00 has 2 different automatic airflow modes. Setting the airflow mode is optional.

To set the airflow mode, press the MODE button.

| Natural Mode – Indicated by the palm tree icon on the display panel, this setting will adjust the airflow speed between low, medium and high.
---|---
| Sleep Mode – Indicated by the moon icon on the display panel, this setting will gradually lower the speed at different intervals, depending on the selected fan speed. If the fan speed is set to 3, the cooler will run for 30 minutes on high speed, 30 minutes on medium speed, and then continue to operate on low speed. If the fan speed is set to 2, the cooler will run for 30 minutes on medium speed and then continue to operate on low speed. If the fan speed is set to 1, the cooler will continuously run on low speed
---|---

TIMER BUTTON

This evaporative cooler is equipped with a 7.5 hour programmable timer. To set the timer, press the TIMER button. Each press of this button will add 0.5 hours to the set time.
The set time will be indicated in the middle of the display panel.

SWING BUTTON

| To activate the oscillation feature, press the SWING button. The fan head will automatically oscillate counterclockwise, which directs cool air into a cyclone for a more focused cooling effect.
---|---

USING THE REMOTE CONTROL

The unit is equipped with a remote control. A CR2032 3V coin-type replacement battery is included for your convenience.

To put the battery inside the remote control, insert a cell into the slot located on the back of the remote control and turn it as directed on the remote control.
● The cells shall be disposed of properly, including keeping them away from children; and
● Even used cells may cause injury.
To use the remote control, aim it at the unit’s remote control receiver and select one of the functions on the remote control. The effective distance is about 24″.

ON/SPEED = Power ON and adjusts speed
OFF = Power OFF
TIMER = Timer function of up to 7.5 hours
SWING = Oscillating air louvers
COOLER/HUMIDIFIER = Controls cooling/humidification function
MODE = Adjusts the airflow mode

ADDITIONAL FEATURES

If the water level in the tank drops below the minimum level, the unit will produce an audible alert that will last for 10 seconds. After 10 seconds, the evaporative cooler will automatically turn off.
If the water tank is removed while the unit is on, it will automatically turn off.

CLEANING AND MAINTENANCE ATTENTION:

MAINTENANCE

Always unplug the evaporative cooler from the power supply before servicing or cleaning.

Regular cleaning and maintenance is an essential step in maintaining the longevity of your tower evaporative cooler and ensuring that it operates free of defects. Maintain your evaporative cooler by following these steps:

EXTERIOR CLEANING

Use a soft cloth and a mild soap and warm water solution to clean the unit’s exterior. Do not use harsh cleaners, gasoline, paint thinner, benzene, etc., as these substances can damage the evaporative cooler.
Thoroughly dry all of the cooler’s parts with a soft cloth before reconnecting the unit to the power supply.

CLEANING THE DUST FILTER & COOLING PAD

To prevent the cooling pad and filter from becoming clogged with dust, mineral deposits and other buildup, we recommend that it be cleaned at least once a month.

Remove the dust filter from the back of the unit by pushing down on the two tabs located above the filter and pulling it out. Gently scrub it with a soft brush and rinse with water.
While the dust filter is off, turn the knob on the pad clockwise and pull it out from the back of the unit. Rinse the pad with clean water to remove dust. For a more thorough cleaning, use a diluted vinegar solution to wash the pad. If necessary, immerse the pad in the diluted vinegar solution for 30 seconds to remove hard water buildup. Be sure to rinse the pad thoroughly with clear water to remove vinegar residue.
Allow the filter and the cooling pad to air dry completely before replacing them in the unit.

CLEANING THE WATER TANK

The water tank should be emptied regularly to ensure hygienic use. To clean the tank, rinse it with warm water and a light detergent solution. Rinse with clean water and allow it to dry completely before placing it back into the cooler.

WATER PUMP MAINTENANCE

Hard water buildup can affect the performance of the cooler’s water pump. To prevent malfunctions, clean the pump and internal tubing with a calcium and lime cleaning product (such as CLR) at least once a season.

Empty any water from the tank.
Pour the cleaner into the water tank and close it. Be sure to push the tank in completely to ensure the water pump is lowered into the tank full of cleaner.
With the tank closed, allow the pump to soak for 10 to 20 minutes.
Remove the cooling pad from the back of the unit.
Run the cooler for 30 seconds. This will circulate the cleaning solution through the pump and tubing to remove any leftover mineral deposits. Do not operate longer than 30 seconds, or damage might occur to other parts of the cooler
Rinse the tank and fill it with clean water. Run it for several minutes without the cooling pad in place to ensure the cleaning solution has been rinsed away.
Replace cooling pad and dust filer and operate unit as normal.
If the evaporative cooler will not be in use for an extended period of time, place the unit back in its original carton and keep it stored in a clean, dry place.

TROUBLESHOOTING

Problem	Possible Causes	Solution
There is no airflow.	The power cord is not plugged in.	Check to

make sure the plug is plugged into an outlet. The unit should beep twice once the power supply is connected.
The water tank is not locked into the unit.| Make sure the water tank is locked into the back of the

unit.

The unit does not cool at all.| There is insufficient water in the tank.| Check the water level in the tank and make sure there is enough water.
The cooler/humidifier button was not pressed.| Press the COOLER/ HUMIDIFER button.
The pump is defective.| Contact customer service if there is an issue with the water pump.
The unit does not sufficiently cool.| The cooling pad is not sufficiently saturated with water.| If speed 3 is selected when in cooling mode, the unit will automatically revert to speed 2 for 5 minutes to allow the pad to be fully soaked. The will automatically turn to speed 3 when the pad is soaked.
Water is coming out of the vents.| The cooling pad may be clogged with debris.| Clean the cooling pad by rinsing it in water and allowing it to thoroughly dry. If the problem persists, contact customer service.

LIMITED MANUFACTURER’S WARRANTY

This appliance is covered by a limited manufacturer’s warranty. For one year from the original date of purchase, the manufacturer will repair or replace any parts of this appliance that prove to be defective in materials and workmanship, provided the appliance has been used under normal operating conditions as intended by the manufacturer.

Warranty Terms:
During the first year, any components of this appliance found to be defective due to materials or workmanship will be repaired or replaced, at the manufacturer’s discretion, at no charge to the original purchaser. The purchaser will be responsible for any removal or transportation costs.

Warranty Exclusions:
The warranty will not apply if damage is caused by any of the following:

Power failure
Damage in transit or when moving the appliance
Improper power supply such as low voltage, defective household wiring or inadequate fuses
Accident, alteration, misuse or abuse of the appliance such as using non-approved accessories, inadequate air circulation in the room or abnormal operating conditions (extreme temperatures)
Use in commercial or industrial applications
Fire, water damage, theft, war, riot, hostility or acts of God such as hurricanes, floods, etc.
Use of force or damage caused by external influences
Partially or completely dismantled appliances · Excess wear and tear by the user

Obtaining Service:
When making a warranty claim, please have the original bill of purchase with purchase date available. Once confirmed that your appliance is eligible for warranty service, all repairs will be performed by a NewAir™ authorized repair facility. The purchaser will be responsible for any removal or transportation costs. Replacement parts and/or units will be new, re-manufactured or refurbished and is subject to the manufacturer’s discretion. For technical support and warranty service, please email support@newair.com

newair.com