Aetertek AT-168F Electronic Fences Owner’s Manual

: June 6, 2024
: Aetertek

Aetertek AT-168F Electronic Fences Owner’s Manual

Brand Story of Aetertek

In the 1990s, when elder brother JACK and younger sister TINA were still teenagers, they lived in the Northridge, San Fernando Valley, Los Angels. One day, they saw a discarded puppy while playing outside the house. This puppy was very cute, which made the brother and sister fondle admiringly, so they took the dog back home.
They gave the puppy a hero’s name — Ryan and expected that one day, the puppy Ryan could be the soldier who saved the whole family. The brother and sister played with Ryan every day and regarded it as a part of the family, while Ryan also grew up in this happy atmosphere.
The peaceful and quiet life went on day after day until the early morning of January 17, 1994 when a strong earthquake occurred. A large number of houses collapsed along with landslide. The family members of the brother and sister were trapped under the house and could not get out. However, the heroical Ryan rushed out of the ruins to look for rescue opportunities. Finally, at dawn, the military heard the news and sent a helicopter. Due to the timely rescue, all the family were safe.
Afterwards, the brother, the sister and Ryan had been living happily for more than ten years. One year before the brother and sister graduated from university, Ryan passed away due to senility and illness. Both the brother and sister were very sad. So they created the brand AETERTEK with the gratitude and yearning for Ryan, and provided pet-friendly high-tech electronic products full of human care for the vast number of pet lovers all around the world.

AT-168F System Components

Transmitter Transmitter mouting screws Transmitter power adaptor Bandage Boundary wire Conductor connecting post Plastic Anchors

AT-168F System Components

Receiver
Test Kit
Collar
Flags
Receiver/Collar Charger
Charger Adapter

Quick Start

Step1: Removing 10mm length rubber peels of antenna and test wire, insert the antenna into antenna pedestal like above pictures.

Step2: Plugging in the transmitter to charge. Friendly Tips:Please kindly unplug power adapter and unload the antenna if your item is not going to be used for a long period of time.

Please use the original b wire(493 feet). Pet.Technology.Life If the boundary wire is shorter than the required or its impedance is out of required standard, the transmitter system would shut down signal output automatically. It’s suggested that use the right boundary wire with 328 feet length or above. Otherwise, the transmitter signal would be closed automatically.
If the boundary wire has been broken or the output terminal is not contacted correctly, the transmitter system would alarm automatically for reminding users to check the transmitter boundary wire.

The details of transmitter screen as shown.

Set u p(Transm itter part):

Open the package and take the transmitter out to make preparation like step1and step2.
Plug the charger into transmitter’s DC port and then the transmitter is in sending signal status. The flashing antenna icon in screen means transmitter is working now.
Press the up and down buttons to adjust the cover range of transmitter. The signal level and cover range would be shown in the middle of screen.
Press M button to enter or exit the function manual. After entered this manual, press right or left button to choose flashing icons for the related BEEP, vibrate or shock function. After chose, press the up or down button to turn those functions on/off. There are two shock modes, one is Auto mode, the other is manual mode. Under the auto mode, the shock level is determined by program. Under the manual mode, the shock level is determined by pressing buttons. Users could personalize the shock levels to train dogs.Under manual mode, shock function is not available at dog mode00. The shock level is available from 01 to 10, the higher level is, the stronger shock is. Users could set up the shock level as needed to protect dogs. After set up the related functions, press the M button again to save and exit the function manual.

Notice: According to your own request to adjust the needed modes and levels. Cover range is available from 00-10, the higher level is, the further distance is. The current cover range would be shown in the middle of screen.(Notice: In some special using circumstance, if there is a difference between the reference range and the actual range, users could adjust the signal cover range by increasing or decreasing the signal levels as they need)

Step 3: Charge the receiver. The RED LED light of the receiver will be on while the receiver is charging. When the receiver is fully charged, the BLUE LED will be on. Once you unplug the charger, the RED LED light will stay solid on-waiting for sync. At the same time, the Blue LED light will go off.
Tip 1: It is recommend to charge the transmitter and receiver for up to 3 hours at the first 3 times.

Step 4: Turn the receiver on/off. Bring the magnet on the transmitter near to the magnet switch on the receiver until the receiver vibrates. At that time, the red light will be on/off, indicating that the receiver is
started/off. If you just finish charging, unplug the charger, and the receiver is on already.
Tip 2: To do a self-test, place the magnet on the transmitter near to the ON/OFF area on the receiver for 3 times, and the receiver will beep, vibrate or shock with the blue light on, indicating the receiver works normally.
Tip 3:After 1 minute of inactivity, transmitter will go into sleep mode. You can wake it up by pressing any Junction keys.

Set up{Receiver part):

0pen the packge and take the receiver out to set up like step3. The first three times charging must be higher than 3 hours to sure the battery optimum performance.
Plug the charger into receiver’s charging port, beep and vibrate would be occurred, red light would be on at the same time while charging. After 3-4 hours, the blue light would be on and means this receiver has been fully charge to use. After unplugged the charger, there is a hint to inform the charging is stop.(Notice: please make sure the charging waterproof rubber cap is well when using this receiver or not being charged.)
Put the magnet of the receiver on the magnet of the transmitter for 3 seconds until beeps, vibrates and the red light on, that means this receiver is on. If the transmitter is on while turning the receiver on, the receiver would sync with this transmitter automatically. After synced successfully, you can use this system for your dog training.
After turned this receiver on, put the test kit on the prongs of receiver and then, use the magnet of the transmitter touch the magnet of receiver three times shortly to make a self test which could trigger a round of beep, vibrate and shock function. If all is well, this receiver could be wore.
5.Put the collar through the receiver. After adjusted to the right position, wear it on dog’s neck and make sure the prongs have been touched directly to dog’s neck skin so that the functions
could work normally.(Please kindly leave a finger width space between the collar and dog’s skin for comfortable wearing experience and well working function.)

AT-168F Dog E-Fence Wiring Sketch Map

AT-168F Dog E-Fence Training

Training the dogs to stay inside of the covered range:

First, set the transmitter level and move the receiver according to the reference covered range. And if the receiver is close to the boundary, the Blue light would start and the closer to the boundary, the faster the beep sound would be made, and then the vibrate would be triggered. If your dog is still getting close to the boundary, the shock would be activated. The shock degree is determinated by the transmitter controlling. If your dog has come back to the covered range, the warning functions would stop immediately. You can place the flags on the boundary and repeat training to let your dog learn this boundary. (If there is any environmental
factor which may be affected signals, please kindly adjust the signal level based on your own needs. And it is usual to meet such situation because different environments may cause different signals.) Therefore there is an error between the actual distance and displayed distance while using.

Trouble Shooting

A:The Transmitter /Receiver runs out of batteries quickly.
1:Make sure the charger and Transmitter/Receiver are securely connected.
2:Charge the Transmitter/Receiver for 3 hours or above.
B:The Transmitter can’t match the Receiver successfully.
1:Make sure the intensity level is not on ZERO.
2:Check whether the antenna is installed correctly.
3:Ensure the receiver is turned on and in sync waiting status.
C:The Receiver doesn’t respond to the Transmitter.
1:Make sure the intensity level is not on ZERO.
Q~®
Professional Dog E-Fence
AT-168F
2:Make sure the Receiver has been synced with the Transmitter and the Transmitter is in the correct dog system.
Never change the dog system after the system has been synced!
3:Make sure the Receiver and Transmitter have enough power.
D:The training system has no effect on my dog.
1:Make sure the Receiver is working and the shocking prongs touch dog’s skin closely.
2:Try increasing the intensity level.
E:The Transmitter can’t remotely control 1 or 2 Receivers.
1:Make sure you sync different Receivers separately.
2:Only in the correct dog system, can you operate the corresponding receiver or dog.
3:Whenever the Receiver/Transmitter is out of power and recharged, you need to sync them once again.
F:The training system is only available in short range.
1:Check whether the antenna is installed correctly.
2:Make sure there is no strong signal interference from your surroundings. The Transmitter’s control range could
fluctuate subject to surroundings, obstacles, or even the weather.

Trouble Shooting

G: What is the function of the rubber cap outside the charging port?
It prevents dust or water from coming into the charging port effectively. You need to plug the cap into the charging port tightly when charging is completed.
H:The Receiver beeps, vibrates or shocks by itself constantly or occasionally.
1:Make sure the Receiver has enough power, because the Receiver will alarm when it runs out of power.
2:Make sure any button of the Transmitter has not been touched.
3:Sync the Receiver with the Transmitter once again.
Q~!!!!:~®
Professional Dog E-Fence
AT-168F
l:After you unplug charger, the red LED light in the Receiver stays in solid to wait for sync, however it can never be synced with Transmitter.
Please turn off your Receiver and re-sync it.
J:My Receiver seems to work by itself without the operation of the Transmitter.
Check whether the auto anti bark function is on. If Yes, turn it off.
K:The Auto anti bark feature is not working properly.
-13-
1: Make sure the auto anti bark feature had been turned on, then you can test the function by scratching the shocking prongs on the surface of a desk, and the qualified Receiver will start to beep and vibrate.
2: Do an auto anti bark test onwww.aetertek.com.(http://www.aetertek.com/pages /Auto-anti-bark-feature-test.html).

Training Tips

This product is intended to support behavioral training and is not designed to be used without necessary interaction. Always praise your dog for good behavior. Verbal commands with positive reinforcement will contribute to success of your training and will achieve the fastest and most desirable results possible.
Professional Dog E-Fence AT-168F
The recommended age for training is a minimum of 6 months, provided that dog has the attention span and capability to learn basic commands. And it should not be used on aggressive or elderly animals in poor health or animals otherwise unable to withstand the stimulus. Use verbal commands first, and supplement with a corrective stimulus only as needed. Be consistent with your verbal commands, using the same words every time. Work with your pet on one behavior at a time to avoid confusion and frustration. Use as little stimulus as possible and only to reinforce verbal commands when necessary. Do not over correct your dog. For example, use the beeps as warning by pressing Beep button. The dog will become conditioned to the beep preceding the corrective stimulus and will soon learn to recognize the beep as a warning along with your verbal
command. Do not rely on this product solely to train your dog. Some dogs will not respond to this product. Aetertek cannot guarantee the effectiveness of this or any trainer on your dog. If your dog shows signs of growling, snarling, biting or aggression while using the collar, discontinue use immediately and contact a professional trainer for advice.

Safety Guide

It is forbidden to open the receiver in case of breakage of the machine or harm the waterproof Feature; otherwise it will violate warranty rules.
Professional Dog E-Fence
AT-168F
In order to guarantee submersible feature, the waterproof rubber charging lid should be plugged in tightly.
Only use the supplied adaptor to charge the receiver, otherwise the receiver will probably be damaged.
Users are NOT suggested to touch the mental prongs on the receiver, otherwise it will harm human body in case of shocking operation. To test shock correction, please use the supplied test kit.
lf there is water in the charging hole, please dry it before charge the receiver
Any collar worn for extended periods can cause a condition similar to bedsores, know as Pressure Necrosis. To reduce the possibility, you must do the followings(VERY IMPORTANT):
a. Never leave the collar on dog for more than 12 hours per day;
b. Examine the dog’s neck daily for any signs of a rash or sore;
c. Supervise your dog during the first 2 days of training;
d. Check the fit to prevent excessive pressure. you should be able to insert one finger between the collar strap and your dog’s skin;
e. Wash the dog’s neck area and the correction poles as often as needed to keep the area and poles clean.
If signs of skin irritation are noticed, immediately discontinue use and apply antibiotic ointment to help and sooth the area.

Information on Terms of Use & Limitation of Liability

Terms of Use
This product is offered to you conditioned upon your acceptance without modification of the terms, conditions, notices contained herein. Usage of this product implies acceptance of all such terms, conditions, and notices.
Proper Use
Professional Dog E-Fence AT-168F
This product is designed for use with dogs where training is desired. The specific temperament of your dog may not work with this product. We recommend that you not use this product if your dog is less than 8 pounds or if your dog is aggressive. If you are unsure whether this is appropriate for your dog, please consult your veterinarian, certified trainer or contact our customer support.
3No Unlawful or Prohibited Use
This product is designed for use with dogs only. This dog training device is not intended to harm, injure, or provoke.
Using this product in a way that is not intended could result in violation of Federal, State or local laws.
Limitation of Liability
In no event shall Aetertek be liable for any direct, indirect, punitive, incidental, special or consequential damages, or any damages whatsoever arising out of or connected with the use or misuse of this product. Buyer assumes all risks and liability from the use ofthis product.
As agreed by related parts,
the seller is responsible for after-sale service, and Aetertek only provide technical support. So if you have any problems related to quality warranty, please contact the seller.
Modification ofTerms and Conditions
Aetertek reserves the right to change the terms, conditions, and notices under which this product is offered.

Warranty Card

Thank you for purchasing our dog trainer, one of the best training systems available for training your dog.
Aetertek warrants the product to be free from defects in material and workmanship, arising under normal use for a period of 1 year from the date of original purchase when brand new. Misuse, loss or improper handling is not covered.
Aetertek will not pay for transport/insurance costs incurred in returning the product to our authorized
Reseller, such as loss of time, inconvenience, loss of use of your product, loss of your product and any incidental or consequential damages.
To be entitled for 1 year international limited warranty of our dog trainer, please fill in the warranty card and keep it safe together with your proof of purchase.
Failure to provide documentation will void warranty.
This warranty extends only to original purchaser and is non-transferable.