BUTURE BR600 Jump Starter User Manual
- June 6, 2024
- BUTURE
Table of Contents
BUTURE BR600 Jump Starter
Package Content
BUTURE
BR600 Jump Starter| Smart Jumper Cables|
Type C
Cable
---|---|---
EC5
Cigarette Lighter| User Manual| Storage Box
Introduction
Thank you for purchasing BUTURE BR600 car jump starter. Please read the user manual carefully before you start to use the product.
Key Features
- A Powerful Jump Starter: Car Jump Starter with 2500 amps peak current can jump starts 12V cars, SUV, truck or van (All Gas or 8.0L Diesel) in seconds up to 30 times on a single charge.
- Power Bank & Wireless Charger:10W wireless charger function and large 23800mAh battery capacity can provide sufficient power to quick charge your smartphones.
- Dual USB Charger with QC3.0 & 5V 2.4A: It can full charge your laptops, smart phones, tablets, and other devices at the fastest speed possible.
- Safety Protection: The high quality and spray gold clamps with a built-in protection circuit provides over-current protection, short circuit protection, over-load protection, over-voltage protection, over-charge protection. Provide ultimate protection for your safety.
- A Life Saver: 4 modes LED light: flashlight, strobe light, SOS signal light, and warning light, built-in safety hammer for emergency.
Know Your Product
- Jump Starting Port
- LED Light
- QC3.0 USB Output
- 5V/2.4A USB Output
- TYPE C Input
- Power Switch
- Battery Indicator
- Wireless charger
- Safety Hammer
Powerful Circuit Protection System – Smart Clamps
- Red Jumper Cable (+)
- Black Jumper Cable (-)
- Smart Clamp Plug
Technical Specifications
No | Function | Operation |
---|---|---|
1 | ON/OFF Button | Press the button to charge your devices. Press the button to |
see the remaining capacity Long press the button to turn on/off the flashlight
2| Flashlight| Normal, SOS, Strobe, Warning Light, off
3| Charge indicator light| Shows the charging press:25%,50%,75% and 100%
4| USB C input| Charge the stater with Type c cable
5| Output 1 QC3.0| Charge your phone,tablet,camera,etc.75% faster than a
standard charge
6| Output 2 USB| Charge your phone,tablet,camera,etc. 5V/2.4A 12W output
7| Wireless charger| Charge your phone or other devices which can support
wireless charger
8| Jump starting port| Insert the plug into the jump starting port
9| Safety hammer| Use in emergency or dangerous situation
Technical Details
Mode | BR600 |
---|---|
Capacity | 23800mAh |
Starting Current | 1200A |
Peak Current | 2500A |
USB C Input | 9V/2A, 5V/3A |
Output 1 | 9V/2A, 5V/2.4A |
Output 2 | 5V/2.4A |
Wireless Charger | 10W |
Dimensions(LWH) | 18395.542.8 |
Overload/Discharge Fuse | ≤13V±0.3V |
Working Temperature | 20℃~60℃ / -4℉~140℉ |
Backflow Protection | ≥12.6V±0.3V |
Short circuit fuse protection | √ |
Reverse polarity protection | √ |
Operation
Power indicator light
Press the power button to check the capacity of the Jump starter.Indicator
Lights as below picture(25%,50%,75%,100%)
Recharge the Jump starter
NOTE: The wall charger or car charger is not included in the package, you can use a universal USB charger to recharge the unit, such as your phone or pad charger(2A above is suggested)
At Home:
- Plug the USB cable into any USB wall adaptor (5V 2A above, not included)
- Connect the UCB C cablecincluded to the unit
In Car:
- Plug the USB car adapter(not included)into an available 12v socket
- Connect the USB C (included ) to the unit.
Note: It is recommended to recharge the Jump starter every 3-4months to
maintain the efficiency and prolong the service life of the internal battery
even if the unit has not been used.
Charging your devices from the USB output
Use the original manufacturer’s USB cable that came with your device and plug it into one of the USB output ports.You can charge two devices at the same time.One of the ports has a maximum output of 9V/2A while the other has a maximum output of 5V/2.4A.Press the power button once to begin charging your device.The power level indicator will show the battery level.To check the power capacity again, simply press the power button once.
To Jump Start Your Car
To jump start the vehicle battery, put the vehicle in park(neutral if the
vehicle has a manual transmission)and engage the emergency brake. Locate the
battery for the vehicle and follow the steps listed below.
Jump cables are color-coded, RED for POSITIVE(+)and BLACK for NEGATIVE(-). Do
not mix up the cables or allow the metal ends to touch together because this
may damage the battery. charging system and/or electronics on a vehicle.
Note: This product is for 12V car only. Check to make sure that 3 or 4
indicator lights are illuminated(battery level is above 50%)before you use it
to start your car.
Step1: Insert the plug of the smart battery clamp completely into the
jump starter. If the green and red light indicators on the battery clamp are
flashing alternately, you are safe to move on to the next step.
Step 2: Connect the red clamp to the positive terminal(+)of the car
battery and connect the black clamp to the negative(-)of the car battery. If
the indicator light of the smart clamp is solid green, you can move on to the
next step.
However, if the red indicator light is on :
- The battery clamp may be connected in reverse. In this case, you need to disconnect the battery clamp from the vehicle and the jump starter. 2. Adjust the clamps for maximum contact with the battery terminals.
Step3: Start Your Car. If you failed to start your car, you need to disconnect the battery clamp from the vehicle and the jump starter.wait for at least 30 seconds, then try again.
Step 4: Once your car is started. Remove the battery clamp from the car-
battery and the jump starter within 30 seconds.
In any of the following situations, the smart clamp turns protection on:
LED indicator | Situations |
---|---|
The red/green led will flash | Ready to work |
The green light is always on | Work status |
The red light is always on |
- battery clamp is reversely connected –check whether the clip is reversely connected 2.the clamp is short-circuited —-check whether two clamps together connect or connect both cable clamps to the same piece of metal
The red light flashes slowly| Back charge protection, the voltage of the car
battery is higher than 12.6V. —No jump starter needed. The car battery is
enough to start your car
The red light LED flashes quickly| The temperature of the clamp exceeds
65±5degrees —-remove the clamp until the red-green led flash
The green light flashes slowly| The voltage of the starter is too low —-try to
replace the startup power supply or charge it in time
Warnings
- When jump-starting a vehicle, please ensure that the blue plug is securely fitted into the jump start socket on your jump starter
- Do not allow this product in water
- Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust
- Do not modify or disassemble the product
- Do not store in locations where the temperature may exceed 140 c60¥
- If battery leakage occurs, take it to your local battery recycling center for disposal, do not attempt to use it.
- This car jump starter is for use with 12V vehicles only.
Battery Disposal
The battery is self-contained and not consumer replaceable, The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product.
Battery Disposal
Issue | Cause | Remedy |
---|---|---|
Can not jump start | Wrong connection | Make sure to clamp the RED jumper cable |
to the Positive(+)post on the battery. And Black jumper cable to
Negative(-)post.
30-second timer to jump start has expired| Disconnect the cables from the
vehicle battery and reconnect it.
Low battery status| Recharge the unit until at least three solid lights
LED light keeps flashing| Protection is working| Refer to the LED Indicator
Table of the manual
No wall adaptor| Charge the unit via your phone charger| Plug the USB cable
into a universal wall adapter (2A above is suggested), such as your phone or
pad charger
Warranty
Our company provides customers with warranty of 24 months from the date of purchase.
Contact US
For additional assistance or warranty cover claim, please contact us:
E-Mail:support@ibuture.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>