BUTURE Beta05 Jump Stater User Guide
- June 1, 2024
- BUTURE
Table of Contents
BUTURE Beta05 Jump Stater
Specifications
- Product: Beta05 Jump Starter
- Input: USB-C
- USB Outputs: USB1, USB2 (18W)
- Features: Jumpstart Port, LED Light, Power Button, Power Level Indicator, Force Start Button
- Compatibility: 12V vehicles
Product Usage Instructions
Jump Start Your Car
- Insert the jumper cable into the jump starter.
- Connect the clamps to the car battery (red to +, black to -).
- The jumper cable indicator turns solid green.
- Start your car engine.
Force Start Function
- If the car doesn’t start after three attempts, use the Force Start Function:
- Press the force start button for 5 seconds.
- The jumper cable indicator turns green.
- Start your car engine.
Recharge
- Insert the charging cable into the USB-C port.
- Connect to a corresponding adaptor (not included).
Charge Electronic Devices
- Plug the cable into any USB output port.
- Press the power button to start charging.
LED Lighting
- Press the power button for 3 seconds to cycle through lighting modes:
- Press shortly for a white strobe light.
- Press shortly for the orange strobe light.
- Press shortly for the SOS signal.
- Press shortly to turn off the light.
Precautions
- Do not use it with less than 10% power.
- Recharge every 3 months.
- Wait 30 minutes before recharging after starting the car.
- Allow at least 60 seconds between starts to prevent overheating.
Important Safety Warning
- Store in a cool, well-ventilated place away from children and pets.
- Do not use it if the clamp or cable is damaged.
- Avoid connecting red and black clamps during output.
FAQ
- Q: What should I do if the indicator shows a solid red light?
- A: Follow the specific instructions provided based on the pattern of beeps and lights. If unsure, contact support@ibuture.com with details.
PRODUCT OVERVIEW
- Jumpstart Port
- Display
- USB Output 1
- USB Output 2 (18W)
- Power Button
- USB C Input
- LED Light
- Power Level
- Port Using
- Charging
- Discharging
- Indicator
- Force Start Button
JUMP START YOUR CAR
- Insert the jumper cable into the jump starter and connect the clamps to the car battery (red to +, black to -).
- The indicator of the jumper cable turns solid green.
- Start your car engine.
ABOUT THE FORCE START FUNCTION
- If three attempts fail when you correctly connect the clamps to your car, you can use the Force Start Function to enter boost mode.
3 steps to fix the problem
- Press the force start button for 5 seconds.
- The indicator of the jumper cable is green.
- Start your car engine.
Warning: When using the Force Start Function, auto-detection and safety features will be disabled.
ABOUT THE TROUBLESHOOTING
In any of the following situations, the smart clamp will turn protections on:
Indicator | Situations |
---|
Solid red light
| · Jump starter battery is low and needs to be charged
· Startup Timeout Protection
—Press the force start button for about 3 until the indicator turns to steady green. It means that it returns to work
Solid red light with slow and brief beeps
| · Reverse Charge Protection
—Reconnect to try again
Solid red light with quick and brief beeps
| · High-Temperature Protection
—Remove the clamps to let it cool
· Relay Short-circuit
—Jumper cable failure. Contact
support@ibuture.com with details
Solid red light with regular long and short beeps
| · Short-circuit Protection
— Do not connect smart clips or to the same metal
· Reverse-connection Protection
— Reverse smart clip to ensure the right connection
· Over Limit Protection
—Reconnect to try again
The green light flashes 5 times, then the red light is always on
| · Five Intervals of Start-up Protection
—Press the force start button for about 3 until
the indicator turns to steady green. It means that it returns to work
Other
|
Please contact support@ibuture.com with details
RECHARGE
- Insert the charging cable into the USB C port.
- Connect to the corresponding adaptor (adaptor not included).
CHARGE ELECTRONIC DEVICES
- Plug the cable into any USB outlet.
- Press the power button.
LED LIGHTING
PRECAUTIONS
- The product is for 12V vehicles only.
- Do not use the product with less than 10% power as this will damage the product.
- Recharge every 3 months to prolong the lifespan.
- Wait at least 30 minutes before recharging after starting the car.
- 60s is recommended between starts, otherwise, it will overheat.
IMPORTANT SAFETY WARNING
- Store in a cool and well-ventilated place out of reach of children and pets.
- Do not place the product in a high-temperature environment for a long time. The operation temperature of this product is -20~60℃. The storage temperature should not exceed 50℃/122℉.
- Only start vehicles with the smart jumper cable supplied by the manufacturer.
- Do not use the product if the clamp or cable is damaged.
- Do not connect the red and black clamps when the product is outputting.
- Do not connect the red and black clamps to the same piece of metal.
- Do not disassemble or modify this product.
- Do not use detergent to clean this product.
- Do not abuse this product and avoid heavy dropping or repeatedly hitting it.
- Do not operate the product in explosive environments such as flammable liquids, gases or dusts.
- Do not immerse the product in water.
- Do not litter the product and it should be safely recycled.
- Do not incinerate the product or be exposed to high temperatures, as they may explode.
- Only use replacement parts or accessories provided or recommended by the manufacturer.
CONTACT
WHERE TO GET MORE HELP
- Scan And Download the PDF Version Of the User Manual
- https://ibuture.com/pages/user-manuals.
- Support@ibuture.com.
- https://ibuture.com.
- @buture.official
- @buture.official
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>