BUTURE BR700 Jump Starter and Air Compressor User Manual

June 4, 2024
BUTURE

BUTURE BR700 Jump Starter and Air Compressor

Package Content

BR700 Jump Starter & Air Compressor


Smart Clamps

|

DC Cigarette Lighter Adapter

USB To Type-C Cable

|

Valve Adapter x 3

User Manual

|

Storage Box

Introduction

Thank you for purchasing SUTURE BR700 car jump starter kit.Please read the user manual carefully before you start to use the product.

Key Features

  • A Powerful Jump Starter: Car Jump Starter with 2500 amps peak current can jump start your flat battery (All Gas or 8.0L Diesel) in 1-3 seconds up to 30 times on a single charge.
  • A Powerful Tire Inflater: Auto start aid and 150PSI tire inflater 2 in 1. You can inflate your car tires anytime and anywhere.
  • A Compact Power Station: The massive 23800mAh capacity can fast charge your phone with dual USB ports and can also power your other car accessories using the 12V 1 0A DC port.
  • Safety Protection: The high quality and spray gold clamps with a built-in protection circuit provide over-current protection, short circuit protection, over-load protection, over-voltage protection, over-charge protection. Provide ultimate protection for your safety.
  • 5W Emergency LED Light: The latest 5W LED camping light to help you start your car in the dark or during night time emergencies.

Know Your Product



No.

| Function| Operation
---|---|---

1

| LCD Power Indicator| Show the charging process and remaining power

2

| Power Button| Press the Power Button to turn ON/OFF the device and show the remaining capacity.
(The device will automatically switch off after stopping operation or output for 10 minutes.)
Long press the button to turn ON/OFF the LED Light

3

| R Button| Activate the LCD Air Pressure Indicator. Switch the unit of output air pressure.

4

| LCD
Air Pressure Display| Display the air pressure of the connected tire.
Display the output air pressure.Pressurize

5

| + Button| Pressurize

6

| -Button| Decompress

7

| LED Light| Illumination

8

| ON/OFF Button| Turn ON / Turn OFF the air compressor(Use after setting the output air pressure)

9

| Air Hose| Connect car tires

10

| USB Output Port 2| Charge your phone, tablet, camera, etc.

11

| USB Output Port 1| Charge your phone. tablet, camera, etc.75% faster than a standard charge

12

| DC 12V-16V/10A Output Port| power your other devices

13

| Type-C Input| Recharge the jump starter

14

| EC5 Output Port| Insert the plug of the clamp completely

15

| Battery Clamp Plug| Insert the plug of the clamp completelylnsert the plug of the clamp completely

16

| LED Indicator| Show the work status of the battery clamp

17

| Red Battery Clamp| Connect to the positive terminal of the car battery

18

| Black Battery Clamp| Connect to the negative terminal of the car battery

Technical Specifications

Model BR700
Battery Capacity 23800mAh
Starting Current 1200A
Peak Current 2500A
Jump Start Output 12V
DC Output 12-16V/10A
USB C Input 5V/3A, 9V/2A, 12V/1.5A
USB Output 1 5V/3A , 9V/2A, 12V/1.5A
USB Output2 5V/2.1A
LED Light Power White: 5W
Recharging Time Quick Charging: 4-4.5hrs
Dimensions(LwH) 21517oasmm
Air Compressor Pump Maximum Air Pressure 150PSI
Operating Temperature -20 C~60 C / -4 1’~140 1′

Operation Guide

Recharge the Jump starter

NOTE: The wall charger or car charger is not included in the package, you can use a universal USB charger to recharge the unit, such as your phone or pad charger(2A above is suggested}
At Home:

  1. Plug the USB cable into any USB wall adaptor (5V 2Aabove, not included)
  2. Connect the USB C cable (included) to the unit

In Car:

  1. plug the USB car adapter(not included)into the car socket
  2. connecl the USB C cable (included ) lo the unit.
    Note: It is recommended to recharge the Jump starter every 3-4months to maintain the efficiency and prolong the service life of the internal battery even if the unit has not been used.
Charging your devices from the USB output

Use the original manufacturer’s USB cable that came with your device and plug it into one of the USB output ports.You can charge two devices at the same lime.One of the ports has a maximum output of 12V/1.5A while the other has a maximum output of 5V/2.1A.Press the power button once to begin charging your device.The power level indicator will show the battery level.To check the power capacity again, simply press the power button once.

LED Light

Please press&hold Power Button for 3 seconds to turn on/ off the LED light.

Safety Precautions

By owning a Jump Starter, you have everything you need to jump start a vehicle-no need to wait for help. BR?00 to the rescue!
We know you’re excited, but before jumping your vehicle, please be sure to take some precautionary steps:

  • Read your vehicle owner’s manual first as the manufacturer may have specific steps and precautions that pertain to your vehicle.
  • Be sure to turn off all electronics in your car (radio, lights, etc.) before jump starting.
  • Make sure you are in a dry, well-ventilated area. Never jump start a vehicle in an enclosed area.
  • Remove any moisture from your jump starter unit, accessories, and your vehicle’s battery. Never attempt to jump start a vehicle when moisture is present. Check that the vehicle’s battery terminals are dean to ensure the best conductivity.
  • Properly identify the vehicle battery’s positive (+, red) and negative (-, black terminals before connecting the clamps.
  • When using the damps, do not allow the metal teeth of the black clamp to touch the metal teeth of the red damp.
  • When using the damps, DO NOT connect the RED damp to the vehicle battery negative(-) terminal, or the BLACK damp to the vehicle battery’s positive (+)terminal.
  • When connecting smart damps to the battery terminals, ensure the copper teeth on each side of the clamp make good contact with the terminal. The better the connection, the easier it will be to start your vehicle.

NOTE: When adjusting the clamps please be sure to disconnect your Jump Starter first. This will prevent the occurrence of minor sparks.

To Jump Start Your Car

Step 1: Insert the plug of the battery damps completely into the jump starter, the red and green lights flashing alternately.

Step 2: Connectthe red damp to the positive electrode(+) of the car battery and the black clamp to negative one(-)

Step 3: Start the vehicle.
If the engine does not start on the firsllry, disconnect ilfrom the car battery and wait for at least 20 seconds before reconnecting.

Step 4: When the vehicle is started, remove the battery clamp from the car battery and the jump starter within 30 seconds.

NOTE: After the green light of the smart clip is always on (work status), do not disconnected or change the connection between the clip and the car battery to avoid short circuits or reverse connection.

Inflating the Vehicle Tire

Please read safety instructions carefully before use:

  • For safety reasons, the device should be KEPT OUT OF REACH OF CHILDREN.
  • Inspect the SUTURE BR700 Jump Starter before each inflates, ensuring the valve and the air hose are not damaged.
  • Do not bend or restrict the air hose while the compressor is in use.
  • Avoid using in rainy or wet conditions as water entering the unit can cause internal damage and premature failure.
  • In case of an electrical or mechanical fault, immediately switch off and unplug the compressor.
  • Only use on tires and inflatable items.
  • Take extra care not to over-inflate when inflating other inflatable items such as sports ball, bike tires, air bed, etc
  • Please refer to your vehicle handbook for the correct tire pressure required for your vehicle.

Step 1: Press the Power Button to activate the device. Then press the R Button to activate the LCD Air Pressure Display and choose your preferred pressure type in psi, bar, kPa or kg/cm.

Step 2: Press the + Button/-Button to increase/decrease the air pressure value on the LCD Air Pressure Display until your desired pressure is reached.
NOTE: Check your car’s standard tire pressure before you set your desired pressure. The standard tire pressure is usually displayed in the vehicle users manual, the label next to the cab door (near the B pillar), the drawer next to the driver’s seat, the fuel door, etc.

Step 3: Remove the dust cap from the tire valve. Carefully remove the air hose from BR700 Jump Starter and connect it securely onto the tire valve, then press down the handle to fix the air hose. Once attached, your tire pressure will be displayed on the LCD Air Pressure Display.
NOTE: The high temperature will pressurize the tire, so please inflate when the tire cools.

Step 4: Turn the ON/OFF Button on to start the air compressor and inflate the tire.
Once the pre-set pressure has been met the device will automatically shut itself off.
Then please turn the ON/OFF Button off to shut the device completely, disconnect the air hose, and replace the dust cap you have taken off.
NOTE: To extend the service life, do not inflate for more than 8 minutes at any one time. If using for extended periods, after inflating for 8 minutes, please let the device rest for 5 minutes allowing for it to cool down.

In any of the following situations, the smart clamp turns protection on:

Step LED Indicator Situations Suggestion
Insert the plug of the smart clamps completely into the jump starter The red
light flashing and sound a long alarm Low power of the jump starter Please

check the jump starter or fully charge it
| |
The red/green light flashing alternately| Ready to work| Continue to the next step
Connect thesmart clamp to the flat battery| The red light is always on and sound a long alarm| The smart clamp is short-circuited. please check whether the red and black clamps together connector connect both cable clamps to the same piece of metal| Please disconnect it from the car battery and jump starter, then wait for at least 20 seconds before reconnecting
The smart clamp is reversely connected
The green light is always on| Work status| Continue to the next step
The green light is always on| The red light flashing and sound a long alarm| Fail to start the vehicle in 30s| Please disconnect it from the car battery and jump starter, then wait for at least 20 seconds before reconnecting .
The red light is always on and sound a short alarm| Starting current of the vehicle is too large| Please disconnect it from the car battery and jump starter, then wait for at least 20 seconds before reconnecting.
Start the vehicle| The red light is always on and sound a long alarm| Start the flat battery successfully, enter anti-recharge protection state| Please remove the battery clamp from the car battery and the jump starter

within 30s

Warnings

  • Always read all instructions carefully before using your Jump Starter
  • Do not submerge your Jump Starter in water, or expose it to rain or moisture.
  • Never open or disassemble your Jump Starter as ii will void your warranty.
  • Do not expose your Jump Starter to fire, intense heat, or flammable liquids.
  • Only charge the product at temperatures between -20″C-+75″C.
  • Keep away from and out of reach of children.
  • Do not insert foreign objects into ANY inputs or outputs
  • Do not allow the metal teeth of the red clamp to touch the metal teeth of the black clamp when connected to your Jump Starter.
  • Do not connect the black damp to the vehicle battery’s positive(+) terminal when connected to your Jump Starter. Do not connect the red damp to the vehicle battery’s negative(-) terminal when connected to your Jump Starter.
  • Do not open your Jump Starter to replace the internal battery. No user replaceable parts are inside your Jump Starter.
  • Always disconnect the jump start cables from your Jump Starter after use and store separately.
    Check the power of the product at least every three months, and charge the product in time.

Battery Disposal

The battery is self-contained and not consumer replaceable, The battery must be disposed of properly when it no longer holds a charge. Proper charging practices will increase the life of the product.

Warranty

Our company provides customers with warranty of 24 months from the date of purchase.

Contact US

For additional assistance or warranty cover claim, please contact us:
E-Mail: support@ibuture.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals