BUTURE BR400 Car Battery Jump Starter User Manual
- June 4, 2024
- BUTURE
Table of Contents
User Manual
Car Battery Jump Starter
support@ibuture.com
Package Content
Introduction
Thank you for purchasing the BUCHER BR400 car jump starter. Please read the
user manual carefully before you start to use the product.
Key Features
-
A Powerful Jump Starter: Car Jump Starter with 1600 amps peak current can jump-start 12V cars, SUVs, trucks,s or vans (8L petrol or 7L diesel engine) in seconds up to 25
times. -
Dual USB Charger with QC3.0 & 5V 2.4A: Ensures the fastest charging efficiency, 4x faster than a conventional charger. Backward compatible with QC 1.0 and 2.0
-
Safety Protection: Premium cells, circuitry, and safety features protect you and your device from surges or short circuits.
-
LifeSaver Kits: 4 modes LED light: flashlight, strobe light, SOS signal light, warning light, and built-in safety hammer for an emergency.
Know Your Product
Powerful Circuit Protection System – Smart Clamps
Getting Started
C harging your Jump Starter
- Please use the provided Type C Cable to charge the product. (Charging adapter is not included, 5V/2A or 9V/2A adapter is recommended )
- Using a 9V/2A adaptor, it will take approximately 4 hours to fully charge the unit. In order to extend the battery life, it is recommended to fully charge the unit every 3 months.
Turn On your Jump Starter
Short press the power switch to boot the system, and the battery indicator
lights will turn on. For energy saving, the system will turn to standby mode
if there is no operation
within 20 seconds.
4 Modes LED Light
Long press the power switch for more than 3 seconds to turn on the light mode.
There are 4 modes which are ON, SOS, Strobe, and Warning, simply short press
the power switch button to change the 4 modes or turn off the light mode. And
you can also press the power switch button for more than 3 seconds to turn off
the light mode.
QC3.0 & 5V 2.4A Dual USB Output
This portable jump starter is also equipped with two smart USB outputs that
provide the fastest charging speed(USB1 – QC3.0:5V3A/9V2A/12V1.5A; USB2 –
5V2.4A) for
your portable electronic devices, such as phones, tablets, Bluetooth
earphones, et c
12V/10A EC5 Cigarette Lighter
Power your devices such as Air Compressor Pump, Car Vacuum Cleaner, etc. Just
plug the adapter into the EC5 Output port and connect the other end with the
device(up to 12V/10A)
Start your Car
| 1. Insert the plug of the smart clip completely into the jump starter, the
green and red lights flash alternately.
---|---
| 2. Correctly clip the red and black clamps to the electrodes of the car
battery (red to positive and black to negative)(The green light stays on)
| 3. Start the vehicle.
| 4. When the vehicle is started, remove the jumper cable from the vehicle
battery immediately.
In any of the following situations, the smart clamp turns on protection mode:
| LED Indicator | Situations |
|---|---|
| The red/green led will flash | Ready to work |
| The green light is always on | Work status |
| The red light is always on | 1. battery clamp is reversely connected |
— check whether the clip is reversely connected 2. The clamp is short-
circuited
–check whether two clamps together connect or connect both cable clamps to the
same piece of metal
The red light flashes slowly| Back charge protection, the voltage of the car
battery is higher than 12.6V No jump starter is needed, the car battery is
enough to start your car
The red LED flashes quickly| The temperature of the clamp exceeds
65(+/-5)degrees — remove the clamp until the red-green led flash
The green light flashes slowly| The voltage of the starter is too low
–try to replace the startup power supply or change it in time
Security Indication
- Use the original smart clamp to start the car.
- DO NOT use this unit if any cable clamp or cord is damaged.
- Start only for 12V vehicles, or it will cause serious damage to the unit.
- Do not jump-start your car when the battery capacity of BR400 is lower than 30%.
- Do not connect two clamps together when the starter is powered on. And do not connect both cable clamps to the same piece of metal.
- If the engine does not start on the first try, disconnect it from the car battery and wait for at least 20 seconds before reconnecting. Maximize three attempts in two minutes.
- Once the engine is successfully started, disconnect the clamps within 30 seconds.
FAQ & Trouble Shooting
Q: Why the indicator is always flashing in red and green? Why the indicator
does not
turn into green light? Why can not start my car?
A: Please note this product only works with a dead/drained battery(12V).
Q: How to turn off this power pack?
A: This power pack will power off automatically when no load or charging is
complete.
Q: What kind of adapter should I use?
A: You can use the charger of your phone or tablet
Q: How many times can this product start the vehicle with full capacity?
A: Up to 25 times at 25℃ / 77℉.(The times may vary based on working
temperature )
Q: What is the working temperature range?
A: -20℃~60℃ / -4℉~140℉
Care and Maintenance
- DO NOT put the product under direct sunlight or in hot areas.
- DO NOT drop or knock your car jump starter.
- DO NOT disassemble the equipment, it may cause damage.
- DO NOT use chemicals or detergents to clean the product.
- DO NOT place the products in a high-temperature environment for long. The
- Check the power of the product at least every three months, and charge the product in time.
Warranty
Our company provides customers with a warranty of 24 months from the date of
purchase.
Contact the US
For additional assistance or warranty cover claim, please contact us:
E-Mail: support@ibuture.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>