AIPHONE IXW-PBX PBX Interface User Guide

IXW-PBX
Programming Guide

Logging into the IXW-PBX

Access the IXW-PBX by entering its IP address and port in a browser. The IP address of the IXW-PBX will be shown on its LCD screen, and the port used is 8089.

Setup Wizard

Change Password
When first logging into the IXW-PBX, you will be prompted to create a new password and enter a valid email address for password recovery.

Network Settings
The network settings for the IXW-PBX will need to be changed in order for it to communicate with IX Series products. Change the Method to “Switch”. The LAN settings will need to match your local network.

Time Zone
Change the Time Zone to match the location of the IX Series system. The date and time format can be changed to match your own preference.

Extensions
Extensions are how the IX Series stations are assigned in the IXW-PBX. Once an extension is created the extension number cannot be edited. For this reason, select Disable Extension Range, and set the Create Number to 1. Set the Start Extension to your first station number, and use a custom SIP Password that will be assigned to all extensions.

Trunk / Routes
The Trunks / Routes will be assigned in later steps in this guide with more in-depth information. Skip this step by clicking next.

Summary
Review the information from each of the previous steps and click save to move on to the next step.

SIP Settings

From the menu bar on the left, expand PBX Settings and click SIP Settings. Adjust the following values pictured below.
General Tab

TCP/TLS Tab

NAT Tab

Editing Extensions

An extension is necessary for each IX Series station to be registered with the IXW-PBX. The extension number will be assigned to the station in the IX Support Tool in the following steps. To configure this, expand Extension/Trunk and click Extensions. Click highlighted below to make changes to the existing extension.

Set the CallerID Number to match the Station Name in the IX Support Tool for consistency. The SIP/IAX password was assigned in the previous steps. Make note that this password will be needed when registering the IXW-PBX.

Adding Additional Extensions
Click and copy the configuration above for each additional station to be registered.

VoIP Trunk Settings

The IXW-PBX will allow SIP Trunks to be used for outbound calls. To configure this, expand Extension/Trunk and click VoIP Trunks. At the top of the page click the Add SIP Trunk button.

Use the Type drop-down and select Register SIP Trunk and enter the Provider and Host Name of the SIP Trunk service provider. The username and password is also required to create a SIP trunk. Verify this information with the provider of the SIP Trunk.

Analog Trunk Settings

The IXW-PBX will also allow for Analog Trunks for outbound calls utilizing a POTS line plugged into one of the FXO Ports on the back of the device. To configure this, expand Extension/Trunk and click Analog Trunks.
At the top of the page click the Add Analog Trunks button. Once the Create New Analog Trunks page is open, select an FXO Port and enter a trunk name.

Note:
The FXO Delay(ms) may need to be adjusted to match the quality of the analog line being used for dial-out.

Registering a Phone Number

To call a phone number from an IX Series station using an analog trunk, the phone number will need to be registered as a VoIP Phone in the Support Tool. Open Support Tool and navigate to Edit > VoIP Phone List, and enter the phone number on the next available row.

Now assign the newly registered phone number to the door station that will be placing the call. From the menu on the left, expand Call Settings and click Called Stations (Door/Sub Stations). Scroll the window to the right and locate the registered “VoIP Phone”, and use the drop-down box to select U in the row of the designated door station.

Outbound Routes

For a station to call out to the registered phone number, it is required to create an outbound route rule for the analog trunk. Expand Extension / Trunk from the menu on the left and click on Outbound Routes. Once the Outbound Routes page opens click on the Add button.

Registering the IXW-PBX

The IXW-PBX must be registered to the IX Series stations for the stations to call out. From the menu on the left, expand Network Settings and click SIP. Enter the extension number in the ID column, the SIP password in the password column, and the IP address of the IXW-PBX in the IPv4 Address column.

Uploading the Settings

In this step, upload the newly configured settings to the IX Series stations. To test your system, press the call button on the door station. The phone extension that was programmed to ring should receive the call. Answer it and ensure that you have 2-way communication between the phone extension and the door station.

For more details about the features and information above, please contact Technical Support.
Aiphone Corporation
www.aiphone.com
tech@aiphone.com
800-692-0200

Documents / Resources

| AIPHONE IXW-PBX PBX Interface [pdf] User Guide
IXW-PBX, PBX Interface
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>