beok TDR89 Wi-Fi Thermostat User Guide
- June 16, 2024
- BEOK
Table of Contents
beok TDR89 Wi-Fi Thermostat
THIS THERMOSTAT IS SUITABLE FOR WATER HEATING, ELECTRIC HEATING AND GAS BOILER
Welcome
Thank you for your trust and support. By adopting higher-end technology and
more perfect technology, your new thermostat will provide you with the right
temperature environment every day in the future, making your life more
comfortable and your living environment more stylish and beautiful. For
detailed instructions on the installation and use of this thermostat, please
read this manual carefully. Please contact a professional to install the
thermostat for you and install and use the product to the extent permitted by
law.
Application
An intelligent digital temperature controller is a floor heating system
suitable for room temperature control and household temperature control. It
controls the operating state of the floor heating equipment by comparing the
ambient temperature with the set temperature, which improves comfort and
achieves energy saving. This digital temperature controller adopts
microcomputer control technology and is equipped with full-screen display
touch buttons, which is elegant in design and easy to use. The thermostat has
manual automatic, programmable and state memory functions.
Product packaging
- Thermostat host 1 PC
- Qualification certificate 1 PC
- Sensing line (optional) 1 PC
- Manual 1 PC
- Screw 2 PCS
Product Model
- WP Plumbing 3A
- EP Electric Heating 16A
- WPB linkage, gas boiler 3A
User Notes
- Please read this manual carefully. Improper operation may damage the product or cause dangerous conditions.
- The installation personnel must be well-trained and experienced service technicians.
- After installation, please read this manual carefully and operate the product according to the instructions.
Caution: Risk of electric shock or equipment damage.
Wiring Diagram
Installation procedure
This product is installed with a standard 86 control switch (in compliance with European regulations).
- Connect the power box according to the wiring diagram.
- Separate the power supply from the control board cable.
- Screw the power supply into the box of 86.
- Connect the power board to the control board line, and align the buckle at 30 degrees to complete the installation.
Description of display & Icon
Operating Instruction
- Power on/off: press to turn on/off the thermostat.
- Press the key to switch between manual and automatic modes.
- In the automatic mode, press + or – to adjust the temperature to enter the automatic temporary mode. This mode runs for only one session.
- Press key to enter the clock setting, press the mode key to switch settings options, and press the + and – keys to adjust the value of each parameter.
- Simultaneously press and hold the + and – keys for 5 seconds to add or cancel the child lock.
- WIFI link: When the thermostat is turned on, press and hold the + button for five or eight seconds, the WIFI icon flashes on the thermostat display, and the thermostat enters the code matching state.
Time programming instructions
Long press the key to enter the programming setting, short press the key to
switch options, press the + or – key to adjust the parameters of each option,
and press the key to exit and save mode.
Advanced options
In the shutdown state, press the key and key. Press for 5 seconds to enter the advanced option settings. Press the key to enter the next option, then press the + and – key to adjust options, and press the key to exit the advanced option setting mode.
1
|
Temperature compensation
| The default value of the calibration room temperature is
-2 ℃. Press the up and down keys to adjust. The adjustable range is 9.9 °C to -9.9 ℃.
---|---|---
2
|
Sensor selection
| The temperature sensor is selected as IN by default.
Press the up and down keys to adjust as IN respectively, indicating that the internal.
3
| Modify the
temperature limit
| The default temperature limit value is 35 ℃. Press the up
and down keys to adjust the range from 5 ℃ to 60 ℃.
4
| Temperature
difference start
| The default temperature difference is set to 1 ℃. Press
the up and down keys to adjust the range to 1-10 degrees.
5
|
Antifreeze function
| Set the default anti-freeze function to OFF, display OFF,
press the up key to tum on anti-freeze and display ON.
6
|
Holiday option and turn off weekly programming
| Set the default rest day as double OFF. Press the up and down keys to adjust It to double OFF (1-5), single OFF
(1-6), no OFF (1 -7) and tum off week programming
(OFF).
7
|
Primary and secondary reverse selection
| Set the default main and auxiliary reversal to 0. Press the up and down keys to adjust 0 to tum off the main and auxiliary reversal. 01 means auxiliary reverse, 02 means auxiliary reverse, 03 means main and auxiliary reverse,
shutdown and antifreeze is not on, stop output.
8
| Passive linkage
output delay time
| Set the default passive linkage delay time to 0. Press the
up and down keys to adjust the range of 0-5 minutes.
9
| Set upper temperature limit| The default value of the set temperature upper limit is 60℃, and the adjustment range Is 35-95 ℃ by pressing
the up and down keys.
---|---|---
10
|
Restore Factory Defaults
| Set to restore the factory default setting to display “-”, Press the up button to adjust the display “—”, press the
enter button to restore the factory settings
About WIFI connection
Before using the WIFI thermostat for the first time, you should set the WIFI
signal and configuration through your smartphone or tablet to allow
communication between your connected devices. WIFI connection: When the
thermostat is turned on, press and hold the + button for 5 seconds, the WIFI
icon flashes on the thermostat display, and the thermostat enters the code-
matching state. WIFI connection: Bluetooth thermostat, please turn on the
phone’s Bluetooth
Download the APP
Search for “Tuya” in App market or scan below QR Code to download
Register Account If you don’t have an APP account yet, you can choose to
register or log in via SMS verification code. Click “Create a new account”,
you will enter the Tuya Smart Platform Privacy Policy page. After you click
Agree, you will officially enter the mobile phone registration page.
The system automatically determines the current country/region. You can also
select the country/region manually. After entering your mobile phone number or
email address, click “get verification code” . Enter the received verification
code, then enter the password, and click “finish” to register successfully
.
Add device
- (Bluetooth connection) Turn on the mobile phone’s Bluetooth, turn the device on, and enter the Tuya APP. Click “Add Device” or “+” on the top right of the APP homepage, and enter the “Add Device” interface. It will prompt: find the device to be added (Figure 2) and follow the prompts.
- “Automatic discovery”: Search for devices (Figure 3), and add widgets as prompted on the phone page.
- (WIFI connection) When the thermostat is turned on, press and hold the + button for 5 seconds, the thermostat display will show. Now the WIFI icon flashes (slow flashing), and the thermostat enters the status of code matching. Find the temperature control product (Bluetooth + WIFI model) in the (small household appliance). In the specified network configuration mode, click the confirmation button on the page, select the WIFI that can connect to the Internet in the working area of the device, and enter it. WIFI password, click Next, click according to the page prompt (Figure 2). “Go to connect”, and follow the instructions to find the prompt content (Figure 3), click “Prompt content” and then return to the Tuya APP to enter the network configuration process.
- In that case, the APP for the network configuration process is shown in Figure 1, and the network configuration successfully displays the interface shown in Figure 2. The device’s name with successful network configuration can be modified, and the room’s location can also be selected.
If the distribution network fails, the APP will display the page shown in the figure below. You can choose to add or view the help again. Note: if the connection fails, please confirm whether the temperature control device has entered the code matching state, refer to item 6 of the operation manual.
Display of temperature controller APP interface
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>