PLANET GSD-2022P Gigabit PoE Switch User Manual

PLANET GSD-2022P Gigabit PoE Switch

Package Contents

Thank you for purchasing PLANET 16-Port 10/100/1000T 802.3at PoE+ Ethernet Switch, GSD-2022P. “802.3at PoE+ Switch” mentioned in this Guide refers to the GSD-2022P. Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should contain the following items:

If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Product Features

Physical Port

• 16-port 10/100/1000BASE-T Gigabit RJ45 copper with IEEE 802.3at PoE+ injector function
• 2 10/100/1000BASE-T Gigabit RJ45 copper interfaces
• 2 1000BASE-X SFP slot interfaces

Power over Ethernet

• Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE
• Up to 16 ports of IEEE 802.3af/802.3at devices powered (ports 1~16)
• Supports PoE power up to 32 watts for each PoE port, with a total PoE budget of 185W
• Each port supports 54V DC power to PoE powered device
• Auto detects powered device (PD)
• Supports PD alive function
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m in standard mode with 250m in extend mode

Switching

• Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/ MDI-X
• Supports IEEE802.3x flow control in full-duplex mode and backpressure in half-duplex mode
• Integrates address look-up engine, supporting 8K absolute MAC addresses
• 9K jumbo frame supports all speeds (10/100/1000Mbps)
• Hardware-based DIP switch for Standard, VLAN or Extend mode selection;
• VLAN mode: Ports 1 to 16 cannot communicate with each other, but can communicate with the uplink ports 17 to 18 and SFP ports 19 to 20
• Extend mode: Ports 1 to 8 have data rate of 10Mbps. The farthest transmission distance is up to 250 meters and all ports can communicate with each other.
• VLAN mode is to isolate ports to prevent broadcast storm and defend DHCP spoofing
• Automatic address learning and address aging
• Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

Hardware

• 12-inch desktop size, 1U height
• LED indicators for system power, per port PoE ready and PoE activity, speed, Link/Act
• 1 silent fan to provide stable and efficient power performance
• Supports contact discharge of ±6KV DC and air distance discharge of ±8KV DC for Ethernet ESD protection
• Supports ±6KV surge immunity

Product Specifications

Hardware Specifications
10/100/1000BASE-T

Copper Ports

| 18 auto MDI/MDIX
1000BASE-X SFP

Slots

| 2
---|---

DIP Switch

| Selectable operation mode

Ø Standard

Ø VLAN

Ø Extend

LED

| Ø System:

Power (Green)

Ø 10/100/1000T RJ45 Interfaces

10/100/1000 LNK/ACT (Green),

PoE-in-Use (Amber)

Ø 1000X SFP Interfaces

1000 LNK/ACT (Green)

Dimensions

(W x D x H)

| 280 x 180 x 44 mm (1U height)
Enclosure| Metal
Weight| 1810g
Power Requirements| 100~240V AC, 50/60Hz, 5A max.
Power Consumption/ Dissipation| Max. 201 watts/686 BTU
Thermal Fan| 1
ESD Protection| Contact discharge of ±6KV DC, Air discharge of ±8KV DC
Surge Protection| ±6KV
Installation| Desktop or rack-mount installation
Switching
Switch Architecture| Store-and-Forward
Switch Fabric| 40Gbps/non-blocking
Switch Throughput@64bytes| 29.76Mpps
---|---
MAC Address Table| 8K entries
Jumbo Frame| 9216 bytes
Flow Control| IEEE 802.3x pause frame for full duplex; back pressure for half duplex
Power over Ethernet
PoE Standard| IEEE 802.3at Power over Ethernet Plus/PSE
PoE Injector Ports| 16
PoE Power Supply Type| End-span/Mid-span: 1/2/4/5 (+), 3/6/7/8 (-)

PoE Power Output

| Per port 54V DC, 300mA. max. 15.4 watts (IEEE 802.3af)

Per port 54V DC, 600mA. max. 32 watts (IEEE 802.3at)

PoE Power Budget| 185 watts
Number of PDs, 7 watts| 16
Number of PDs, 15.4 watts| 12
Number of PDs, 30 watts| 6
Standards Conformance
Regulatory Compliance| FCC Part 15 Class A, CE

Standards Compliance

| IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3z Gigabit SX/LX

IEEE 802.3x flow control and back pressure IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy-Efficient Ethernet

---|---
Environment

Operating

| Temperature: 0 ~ 50 degrees C Relative Humidity: 5~ 95% (non-condensing)

Storage

| Temperature: -10 ~ 70 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Hardware Introduction

Front Panel
The Front Panel of the 802.3at PoE+ Switch consists of 18 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports and 2 1000BASE-X SFP slots. The LED Indicators are also located on the front panel of the 802.3at PoE+ Switch.

LED Indicators

System

Per 10/100/1000BASE-T Port

10/100/1000

LNK/ACT

| ****

Green

| Lights to indicate the link through that port is successfully established.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

PoE in Use

| ****

Amber

| Lights to indicate the port is providing

PoE DC in-line power.

Per 1000BASE-X SFP Interface

1000

LNK/ACT

| ****

Green

| Lights to indicate the link through that port is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

Multiple Functions of DIP Switch

The front panel of the 802.3at PoE+ Switch provides one DIP switch for Standard, VLAN or Extend mode selection. The detailed descriptions are shown in the following table.

Standard

VLAN

Extend

|

__

|  | This mode makes the 802.3at PoE+ Switch operate as a general switch and all PoE ports operate at 10/100/1000Mbps auto- negotiation. All ports can communicate with one another.

Standard

VLAN

Extend

|  |

| This mode makes the 802.3at PoE+ Switch operate as a VLAN isolation switch and

1.        Ports 1 to 16 will isolate respectively.

2.        Ports 1 to 16 can only communicate with ports 17~18 (uplink ports) and SFP ports 19~20

Standard

VLAN

Extend

|  |

| This mode makes the 802.3at PoE+ Switch operate as a Long Reach PoE switch and

1.  Ports 1 to 8 support farthest transmission distance of up to 250 meters

2.  Ports 1 to 8 have a data rate of 10Mbps

3.  All ports can communicate with one another.

Please adjust the DIP switch before powering on the 802.3at PoE+ Switch.

Rear Panel

The rear panel of the 802.3at PoE+ Switch indicates an AC power socket, which accepts input power from 100 to 240V AC, 50-60Hz, 5A.

AC Power Receptacle

• The device is a power-required device, which means it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.
• In some areas, installing a surge suppression device may also help to protect your 802.3at PoE+ Switch from being damaged by unregulated surge or current to the 802.3at PoE+ Switch or the power adapter.

Hardware Installation

Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below.

Step 1 : Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch with supplied screws attached to the package. Figure 5-1 shows how to attach brackets to one side of the 802.3at PoE+ Switch.

Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate the warranty.

Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 5-2.

Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at complied PDs and other network devices.
A. Connect one end of a standard network cable to the 10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at PoE+ Switch.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers, etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall outlet.
When the 802.3at PoE+ Switch receives power, the power LED should remain solid Green.

Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot of the 802.3at PoE+ Switch. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the 802.3at PoE+ Switch, as the Figure 5-3 shows.

Approved PLANET SFP Transceivers

PLANET 802.3at PoE+ Switch supports both single mode and multimode SFP transceivers. The website link of approved PLANET SFP transceivers is shown below: https://www.planet.com.tw/en/product/mgb-series-transceiver

Note: It is recommended to use PLANET SFP on the 802.3at PoE+ Switch. If you insert an SFP trans-ceiver that is not supported, the 802.3at PoE+ Switch will not recognize it.

1. Before we connect the 802.3at PoE+ Switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASESX; 1000BASE-LX to 1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
3. To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male duplex LC connector type.
4. To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male duplex LC connector type.

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address: support@planet.com.tw

Copyright © PLANET Technology Corp. 2020 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>