hama 00050562 Home and Office Laminator Din A3/250 Instruction Manual

: June 6, 2024
: Hama

hama 00050562 Home and Office Laminator Din A3/250 Instruction Manual

hama 00050562 Home and Office Laminator Din A3 250 Instruction
Manual

hama 00050562 Home and Office Laminator Din A3 250 -
overview

Operating Instructions

Machine setup

Laminate output (rear)
Roller unlocking (rear)
Connection cable
Laminate intake
On/Off switch
Ready status LED
Power status LED

Introduction

Foreword

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Note – Importance of the operating instructions

Failure to observe the operating instructions when using the product constitutes incorrect use or wilful misuse and is not permitted.

Explanation of warning symbols and notes

Risk of electric shock

This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

Package contents

“Home & Office DIN A3 / 250” Laminator
5 laminating pouches (DIN A3)
These operating instructions

Security

Correct use

This product is intended for the lamination of documents both in the home and in the commercial sector, provided the applications are comparable with typical household use (e.g. in offices, workshops and hotels, etc.).
Do not operate the product continuously, as it is not designed for this.
Use the product only for the intended purpose.
The product is intended only for use inside buildings.
Protect the product from dirt, moisture and overheating and use it in dry rooms only.
Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
Do not use the product in a damp environment and avoid splashing water.
Do not operate the product outside the power limits specified in the technical data.
Do not use the product in areas in which electronic products are not permitted.
Do not drop the product and do not expose it to any major shocks.
This product is not intended for use by persons, including children, with limited physical, sensory or mental abilities or lacking in experience or knowledge, unless they are supervised by a person responsible for their safety or have been instructed on how to use the product.
As with all electrical products, this device should be kept out of the reach of children.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately in accordance with the locally applicable regulations.
Do not modify the product in any way. Doing so voids the warranty.
Only use the article under moderate climatic conditions.

Note

The product is only intended for volumes generated by households.

Note – Commercial use

If the device is used commercially, increased duty of care requirements apply.
Therefore, please observe the accident prevention regulations of the German employer’s liability insurance association for electrical systems and equipment.
Please also observe all accident prevention regulations from other applicable employer’s liability insurance associations and accident insurance companies, as well as any legal regulations applicable to the particular industry and/or location.

Basic safety instructions

Please note the following safety instructions in order to use the device safely:

Check the device before use for any visible external damage. Do not put a damaged device into operation.
People who, as a result of their physical, mental or motor capacities, are unable to operate the device safely must only use the device under supervision or after instruction by a responsible person.
Faulty components must only be replaced with original spare parts. Only these parts are guaranteed to meet the required safety standards.
Protect the device against moisture and the penetration of liquids or objects. In the event of contact with liquid, disconnect the device from the power supply immediately

Warning – Danger of burns on the housing

Do not touch the housing.

Risk of electric shock

Do not open the device or continue to operate it if it becomes damaged.
Do not use the product if the AC adapter, adapter cable or power cable is damaged.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

Installation / Setup

Warning

Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
If you will not be using the product for a prolonged period, disconnect it from mains power.

Note

Set the product up on a level, horizontal and sufficiently stable and heat-resistant surface.
Route all cables so that there is no risk of tripping.
Do not bend or crush the cable.
Protect the connecting cable from hot surfaces and sharp edges.
Always pull directly on the plug when disconnecting the cable, never on the cable itself.
The product must only be operated on a supply network as described on the type plate.

• Connect the network cable to a properly installed and easily accessible network socket.

Operation

Note

Always set the correct temperature for the laminating pouch thickness being used.
When laminating thicker paper or multiple pages, we recommend using a thinner pouch.
Always wait until one laminating operation is finished before starting the next one.
Do not allow the device to run for more than two hours at a time.
Wait around 15 seconds between two laminating processes.
Laminating pouches of all sizes should be introduced into the centre of the opening on the front. Ensure that the sealed end is introduced first. (See Fig. 2)

Switching the device on

Move the On/Off switch (5) to the “COLD” or “HOT” position to switch the device on.
The Power status LED (7) lights up solid blue.

Cold lamination

Move the On/Off switch (5) to the “COLD” position for cold lamination.

Note

If hot lamination was carried out beforehand, it can take up to around 40 minutes before the device has fully cooled.
Special pouches are needed for cold lamination. The seal is created with pressure rather than heat. It is not permanent and does not offer one hundred per cent protection against oxygen and water. The process is suitable for heat-sensitive documents, such as thermal paper, till receipts, driving licences or laser copies. In other words, anything that would be damaged or altered by hot lamination.
Wait until the Ready status LED (6) lights up solid red. The device is cool or is not heating up.
Place the object to be laminated in the corresponding cold lamination pouch.
Guide the pouch into the middle of the front opening (4) on the device. Ensure that the sealed end (see Fig. 2) is introduced first.
The document is output again at the back (1).
If the document has not been fully laminated, repeat the initial steps.
To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller unlocking button (2) and correct the position of the pouch.

Hot lamination

For hot lamination, move the On/Off switch (5) to the “HOT” position.

Warning – Danger of burns on the housing

Do not touch the housing.
Be aware that laminated objects are hot.
Place the laminated object on a level surface to cool down in order to prevent it from curling up.

Note

Special pouches are needed for hot lamination. They are sealed using heat. This seal is permanent and cannot be undone. Only objects that are insensitive to heat should be laminated. From a pouch edge of around 4 mm, the objects are protected so they are virtually waterproof. The thickness of the pouch determines the object’s stability / kink protection.

The Ready LED (6) lights up solid red once the required temperature has been reached.
Place the object to be laminated in the corresponding hot lamination pouch.
Guide the pouch into the middle of the front opening (4) on the device. Ensure that the sealed end (see Fig. 2) is introduced first.
The document is output again at the back (1).
If the document has not been fully laminated, repeat the initial steps.
To interrupt the lamination process (e.g. if the intake angle is incorrect), press the roller unlocking button (2) and correct the position of the pouch.

Switching the device off

Move the On/Off switch (5) to the “OFF” position to switch the device off.
Both status LEDs (6/7) go out.
Remove the mains lead from the socket.
Allow the device to cool down completely before tidying it away.

Care and maintenance

Danger – risk of death from electric shock

Disconnect the mains plug from the socket before starting any cleaning work.

Warning – Danger of burns on the housing

Do not touch the housing.

Warning – damage to the device from moisture

Ensure, when cleaning, that no moisture penetrates the device in order to avoid irreparable damage to it.

The rollers on the laminator must be regularly cleared of dust and any glue residue. To do so, proceed as follows:

Switch the device on – as described in 4.1 Switching the device on.
Move the On/Off switch (5) to the “HOT” position.
Wait until the Ready status LED (6) lights up solid red.
Guide a piece of paper into the middle of the front opening (4).
Repeat the process if there isalot of dirt on the paper.
Clean the outside of the device with a slightly damp cloth.

Troubleshooting

hama 00050562 Home and Office Laminator Din A3 250 -
Troubleshooting

Technical data

hama 00050562 Home and Office Laminator Din A3 250 - Technical
data

Warranty Disclaimer

All of the technical information, data and instructions regarding operation contained in these operating instructions was up to date at the time of printing and is provided based on previous experience and to the best of our knowledge.

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country

This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations.
By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our environment.

Hama GmbH & Co KG
86652 Monheim/ Germany

Service & Support

www.hama.com
+49 9091 502-0

www.hama.com/nep

All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.