CONAIR Number Cut 20 Piece Haircut Kit HC408 Instruction Manual

CONAIR Number Cut 20 Piece Haircut Kit HC408

Product Overview

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER

DANGER — any appliance is electrically live, even when the switch is off. To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquids.
4. Always unplug this appliance from the electrical outlet immediately after using. 5. Unplug this appliance before cleaning.

DO NOT REACH INTO THE WATER

WARNING– To reduce the risk of burns, electric shock, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.
2. This appliance should not be used by, on, or near children or by individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or dropped into water. Return the appliance to an Authorized Service Center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the appliance with the air opening blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair and the like.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, turn all controls to OFF, then remove plug from outlet.
10. Do not place appliance on any surface while it is operating.
11. Do not use this appliance with a damaged or broken comb or with teeth missing from the blades, as injury may occur.
12. Avoid skin contact with moving blades.
13. If the cord becomes tangled during use, turn the unit off and straighten cord before operating again.

OPERATING INSTRUCTIONS

This appliance is used on Alternating Current 120V (AC 60 hertz) only.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in the outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Your new Conair® haircut kit has everything you need to achieve professional haircuts at home. It features a powerful clipper with cutting precision. Also included are 8 numbercoded comb attachments for different hair lengths (including left and right ear combs). It also comes with 2 styling clips to assist you in cutting longer hair styles, a storage case, barber comb, barber scissors, barber cape, cleaning brush, lubricating oil and a blade guard for easy maintenance of the clipper blades.

THE CONAIR GUIDE TO CUTTING HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of hair and dirt, properly oiled, and running smoothly.
2. Place a towel or cape around the neck of the person whose hair is being cut.
3. Seat the person so that his or her head is at your eye level. This gives you greater visibility and control.
4. First, comb hair until it’s tangle-free. Then hold clipper in a comfortable grip. Now you’re ready to cut.
   Please note your [number] cut™ 20-piece haircut kit comes with easy-to-use number-coded combs, so you can easily remember your favorite comb once you start to use the kit on a regular basis.

MEDIUM TO LONG CUT

To begin with, cut only a small amount of hair until you become used to the length each attachment leaves the hair. Try the longest attachment on the clipper first. If you want a shorter cut, you can then use shorter combs.

• Short attachment comb (number 1) cuts hair to 1/8″.
• Medium-Short attachment comb (number 2) cuts hair to 1/4″.
• Medium-Long attachment comb (number 3) cuts hair to 3/8″.
• Long attachment comb (number 4) cuts hair to 1/2″.
• Long attachment comb (number 5) cuts hair to 5/8″.
• Long attachment comb (number 6) cuts hair to 3/4″.
• Long attachment comb (number 7) cuts hair to 7/8″.
• Long attachment comb (number 8) cuts hair to 1″.
• Left ear attachment comb lightly tapers over left ear.
• Right ear attachment comb lightly tapers over right ear.

Attach combs by holding them teeth up, then snapping onto the bottom of the clipper blade.

To remove comb attachments, place index finger and thumb as illustrated; then pull out and up.

NOTE: Never push or shove the clipper through the hair to make it move more quickly. Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed.

To begin cutting hair:

1. The hair should be combed in its natural direction.
   

2. Using the largest attachment comb, trim sides from the bottom upwards. Hold clipper lightly against the hair with teeth of the attachment comb pointing upward, yet flat against the head. Gradually lift the clipper upward and outward through the hair, trimming just a little at a time.

Repeat around sides and back of head.

If you want hair to be even shorter:

A) Apply more pressure to the head with the attachment comb that is in place. This takes a little practice, of course.

OR

B) Just switch to a shorter attachment comb. Remember, it’s better to leave too much hair than too little. For longer hair on top, use the barber comb and lift hair on the top of the head, cutting over the comb. Or, hold the hair between the fingers and cut to desired length. Always working from the front to the back of the head, gradually cut the hair shorter by reducing the space between the comb or fingers and the head. Comb often to check for uneven strands, and to get rid of trimmed hair.

OUTLINING:

Outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see above), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down (see Fig.

1. and, holding it against the skin at the length desired, move the clipper downward.
   

STOP. COMB CHECK.

For best results, do as the professionals do: comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc.

SHORT CUTS TO PERFECT FLAT TOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the crown, using the longest comb setting. Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of the head.

For the front to the crown, cut the hair against the direction in which it grows. Then even it up with the sides.

For a flat top, use the flat comb, not the attachment comb. Just cut hair on top of the head over the flat comb (see Fig. 2).

To taper hair down to the neckline, use attachment comb #1. Comb hair and check for uneven spots. Outline sideburns and neck areas (see “Outlining”).

USER-MAINTENANCE INSTRUCTIONS CARE OF YOUR CLIPPERS

MAINTENANCE OF THE BLADE

Always apply oil to the blades before, during and after use. This will ensure maximum cutting performance. Hold clipper away from your body in a downward position and apply oil on the front and sides of the cutter blade. Wipe excess oil off with a soft dry cloth.

Conair® hair clippers are carefully inspected to insure that the blades are in perfect alignment. You will need to realign the blades if they should be knocked out of alignment. How can you tell if the blades need realigning? Simply match them up, point for point, to conform with the drawing below.

To replace cutting comb and cutter after removal for cleaning, replacement or because they are out of alignment, slide the cutter back onto the black plastic oscillating head. Next, you must make sure that the cutter (small blade) and the cutting comb (large blade) are properly aligned. Line up the new or existing cutting comb with the two screw holes. Place the original screws, one in each hole, and lightly tighten with a Phillips head screwdriver.

Then, match the two blades up, point to point, conforming with the illustration below in Fig. 4.

The top edge of the cutting comb should be 1/32″ to 1/16″ (.79 mm. to 1.59 mm.) higher than the top edge of the cutter. This is important so that the clipper does not cut too close or come in contact with the skin.
The extreme left tooth of the cutting comb must cover or be to the extreme left of the first small tooth of the cutter.
***** Be sure that the extreme right big tooth of the cutter touches the extreme right tooth of the cutting comb.

Any other servicing should be performed by an authorized service representative or that the appliance has no user-serviceable parts. The product is for household use. Do not pull, twist, or wrap line cord around appliance.

SPECIAL OIL

To maintain the blades of your Conair® clipper, always apply oil to the blades before, during and after use. Gently place a few drops of oil on the teeth of the blades, using the special Conair® oil included with your set. Turn the clipper on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair® high-speed clipper. Because it is the right oil to use, it will not slow down the blades. Never use any other product. There is no substitute for Conair oil.

POWER SCREW

The power screw permits you to adjust power to your clipper. You may need to make this adjustment if the power in your house is low. (The Conair® clipper was designed for household use.)

1. With a screwdriver or a dime, turn the power screw counterclockwise until the arm strikes a coil, making a clacking noise (Fig.1).
   

2. Turn the screw clockwise until the noise stops, and then turn about 45 degrees more. This is the maximum power setting (Fig. 2).

ADJUSTABLE TAPER LEVER

Just like professional clippers, the Conair taper lever is positioned at your thumb. You can hold the clipper in your hand and adjust the lever at the same time…while you’re clipping. This taper lever eliminates the need for an attachment comb because it lets you gradually adjust the closeness of the cut. For the closest cut and the shortest hair, push taper lever up as far as it will go. To increase cutting length, slowly push lever down. If you push to the lowest position, it will leave hair about the same length as the short attachment.

Because a different cutting edge is used in each setting, the taper lever lengthens the life of your blades.

Packed-in hair can slow down any clipper. To remove hair without removing the blades, use your cleaning brush to brush hair out of the blades. This should be done after each use. When blades are free of hair, apply a small amount of oil across them.

If you do this after every clipping, especially with heavy hair cutting, the blades should remain in good working condition. If clipper stops cutting and this action doesn’t help, check the blades. If they’ve become dull, replace them. For new blades, send check or money order for $6.50 (see order blank.) This price includes postage and handling, but $10.00 minimum must be met.

Conair Corporation 150 Milford Rd. East Windsor, NJ 08520

CAUTION: Never pull on the clipper cord. Never twist or wrap the cord around the clipper. Lay it flat with the cord coiled up when not in use.

WARNING: IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.
**KEEP AWAY FROM WATER

**

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically alive even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG SMALL APPLIANCES

LIMITED FIVE YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 60 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed below, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3660937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 60-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

© 2010 Conair Corporation SERVICE CENTER CONAIR CORPORATION Service Department 7475 North Glen Harbor Blvd. Glendale, AZ 85307

Once again, thanks for buying a Conair product.
Your Conair® clipper blades are made of high carbon stainless steel. They are engineered for precise, professional results. If blades feel like they are pulling or grabbing hair, it means they are losing their sharpness and should be replaced as soon as possible.
Attachment combs should also be replaced if they are lost or broken. It is easier to cut hair with the accuracy of a pro when the necessary tools are at your fingertips.
Conair makes a variety of accessories for different haircut kits. If your haircut kit does not include them, you may want to consider adding them to your professional haircutting tools.
Left and right ear attachment combs provide effortless, precise cutting around the ears. Styling clips hold hair in place when you are sectioning hair. A styling comb makes it easy to taper or cut hair at an angle. A barber cape ensures a comfortable and neat haircut and a convenient storage pouch keeps all your essentials in one place.
Last but not least, an easy-to-follow 30-minute “Haircuts at Home” video is available. It demonstrates basic haircutting techniques and follows four popular haircuts step by step. It will give you the confidence and instruction you need to give. great-looking haircuts to every member of your family.
To register your Conair product, please simply go to www.conair.com/registration and the site will guide you.

EXCITING ITEMS FROM CONAIR

PT1 Mighty Mini 15-Piece Clipper Kit

Powerful DC motor makes this unique, lightweight clipper/ trimmer a versatile cutting instrument, as it can also be used for detailing and bikini line trimming.

GMT189CGB 13-Piece Trimmer

Rechargeable Beard & Mustache trimmer with stainless steel blades and a 5-position attachment comb for a blended and tapered trim.

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through June 1, 2011. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order. All prices include handling and return postage. Prices are subject to change without notice. Prices are valid only for shipments within the continental United States. Please allow 4­6 weeks for delivery. To avoid delays, please print clearly. We must have a street address, as UPS cannot deliver to a P.O. box.

NAME__
ADDRESS____ APT.
CITY____STATE____ZIP____

TELEPHONE (        )___ (We call only if we have a question about your order.)

For information on other Conair ® haircut kit parts, call: 1-800-3-CONAIR.

Subtotal|
---|---
*Sales Tax|
TOTAL|

Mail to:
Conair Corporation Service Department 150 Milford Road East Windsor, NJ 08520-9730

www.conair.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>