CONAIR BTS7 Dual Jet Bath Spa Instruction Manual

CONAIR BTS7 Dual Jet Bath Spa Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be taken, including the following: Read all instructions before using this appliance.

DANGER – To reduce the risk of electric shock:

1. Always unplug this appliance from the electrical outlet immediately after using or before cleaning.
2. Do not place or store power pack where it can fall or be pulled into a tub or sink. Do not fully immerse in or drop into water or other liquids. Store in a dry place, out of reach of children.
3. Do not reach for an appliance that has fallen into water. Unplug immediately

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
2. This appliance is not a toy!
3. Consult your doctor before using in case of pregnancy, illness, medical condition, or persistent pain.
4. Do not use on any unexplained pain or swollen muscles, or following a serious injury, before consulting your physician.
5. Do not use appliance in close proximity to loose clothing or jewelry.
6. Keep long hair away from appliance while in use.
7. This appliance should not be used by, on, or near children or individuals with certain disabilities.
8. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Conair.
9. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or the power pack has been dropped or submersed in water. Return the appliance to a service center for examination and repair.
10. Do not carry this appliance by the supply cord or use the cord as a handle.
11. Keep the cord away from heated surfaces.
12. Never drop or insert any object into the product.
13. Do not use outdoors.
14. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
15. For use with the Conair-supplied adapter model: SW–110218 only.
16. Use the class 2 power supply in a dry location only.
17. This power unit is intended to be correctly oriented in a vertical or floor mounted position.
18. Do not handle plug with wet hands. Ensure that your hands are dry when operating the controls or removing the plug.
19. To disconnect, turn all controls to the OFF position, then remove plug from outlet.
20. This appliance is for household use only.
21. Never use while sleeping or drowsy.
22. Keep out of the reach of children.

IMPORTANT

Keep hair, fingers, skin, and loose clothing or articles away from suction openings located on sides of unit while Bath Spa is in operation. Otherwise, personal injury may result. Use of shower cap is recommended for persons with long hair. Discontinue use of any oils added to bath water that may affect performance of unit.

CAUTION

• This unit should not be used in the following cases unless directed by physician: tuberculosis, benign and malignant tumors, hemorrhages, inflammations of the skin, phlebitis and thrombosis, open and fresh wounds, bruises, broken skin or varicose veins, or undetermined calf pain.
• Consult your physician if you have any questions regarding therapeutic use of this Bath Spa.
• Do not use if you have any unexplained pain before consulting your physician.
• Discontinue use of unit if pain is present, increases or swelling occurs after use.
• Do not use on any part of the body that is anesthetized.
• Do not use if recent surgery has been performed.
• Never use without removable filter.
• If you are pregnant, consult your physician before use.
• Never run your Bath Spa without water.

FCC MARKINGS

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio  frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which  can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

HOW TO USE

1. With unit securely placed on tub (see “How to Attach Your Bath Spa to Your Tub”), place the power pack as far away from tub as possible so that it cannot easily be pulled into tub.

2. Bath Spa is connected to the power pack by a 15′ line cord. Insert plug into power pack with indexing tab facing down.

3. Plug power pack into 120V wall outlet. Make sure power pack is not on the floor of the bathroom to minimize Jet Stream Bubbles water exposure to the power pack. Fig. 1

4. Fill bathtub with warm water. Ensure water temperature is comfortable to avoid burns. Never use boiling water with your Bath Spa.

5. Adjust height of motor assembly so that outlet nozzles are beneath water. This can be done by moving the motor assembly up and down vertically; the housing employs detentes which will hold the motor assembly at the desired height. KEEP THE WATER LEVEL ABOVE THE FILL LINE.

6. Point the water output nozzles downward.

7. Adjust the bubble control switch on the side of the unit to either “Jet Stream” or “Bubbles” (see Fig. 1).

8. Turn the knob on the top of the Bath Spa to ON (see Fig. 2).

9. Adjust the water output nozzles to create customized water flow in your bathtub. The nozzles can be rotated to customize the direction of the water flow.

10. After use, turn the knob to the OFF position (see Fig. 2), drain water from tub, then remove Bath Spa.
    

11. Rotate your Bath Spa gently over the bathtub to remove excess water, and dry with a soft cloth before storage.

CAUTION: IF BATH SPA FALLS AND BECOMES COMPLETELY IMMERSED IN WATER IN TUB, DO NOT PANIC. UNPLUG FROM WALL OUTLET FIRST. THE BATH SPA HAS BEEN DESIGNED TO WITHSTAND SUBMERSION. ALWAYS REMOVE UNIT FROM BATHTUB. PRESS OFF BUTTON, DRAIN WATER FROM UNIT AND STORE IN A DRY PLACE.

NOTE
You may experience some water spray if the unit shifts during operation. Do not overfill your tub. For best results, get into your tub before filling (Note: Too much water can cause overflow). The Conair® Dual Jet Bath Spa can help you relax, relieve tension, and soothe sore muscles. Consult your physician or physical therapist for recommendations regarding Bath Spa use, including water temperature, duration, and frequency.

CARE AND MAINTENANCE

1. Keep your unit clean and clear of obstruction. Check the outflow control and water intake periodically to make sure they are free of obstruction, hair, lint, and other particles that could block air or water flow. Clean inlet filters by removing filter caps; clean by rinsing in a reverse water flow in a sink or tub. Reinsert on Bath Spa by using the provided alignment marks. See “Fitting and Removing Filter Caps.”
2. Store your Bath Spa in a cool, dry place. Loosely coil the charge cord and lay flat to store. Do not wrap cord around Bath Spa or power pack.

FEATURES

1. Dual multidirectional water jets
2. Telescopic housing
3. Jet stream or bubbles options
4. Removable filters
5. Compact convenience

CLEANING AND DISINFECTING YOUR BATH SPA

1. Your Bath Spa can be cleaned with any mild detergent or soap. After removing plug, cleaning is recommended after each use. Do not use strong chemical cleaners.
2. Disinfect your unit periodically to keep it bacteria free. With frequent use, disinfect weekly. With infrequent use, disinfect after each use.

RECOMMENDED MASSAGING TIMES

Spa massage should generally last 15–20 minutes.
Caution: Read safety rules and operating instructions carefully. This product is intended for indoor use on permanent, right-wall tubs. Do not use outdoors or on the walls of inflatable tubs or pools.

HOW TO ATTACH YOUR BATH SPA TO YOUR TUB

1. Make sure the power knob is in the OFF position. The tub should be clean and empty of water.

2. Extend the folding arm and position unit along edge of tub so the unit is inside the tub and the arm is resting on edge (Fig. 3).

3. Moisten suction cups on motor housing of Bath Spa to increase grip.

4. Secure suction cups by gently applying even pressure on Bath Spa against tub wall (Fig. 3).
   

5. Adjust suction cup on arm so that it adheres directly onto bathtub edge. See Fig. 4 and Suction Cup Position Adjustment section following (Fig. 6).
   

6. Adjust height of motor assembly to desired depth by moving motor housing up or down by hand. Built-in detentes will hold the position you desire (Fig. 5).
   

7. Water may spray if unit is not level when turned on.

SUCTION CUP POSITION ADJUSTMENT

Suction cup underneath the handle can be in one of two positions to suit different bathtubs.
(See Fig. 6) Push and slide the suction cup to the desired position.
Position A: The outermost position for thick-sided tubs.
Position B: The innermost position for thin-sided tubs.

FITTING AND REMOVING FILTER CAPS

TO REMOVE CAPS

1. Turn cap about 20° counterclockwise (Fig. 7). (Filter caps are located on either side of the motor assembly.)
   

2. Line up single hash mark on cap with the center seam on the back body of the unit.

3. Pull cap away from unit.

4. Rinse cap under water to remove hair, lint, etc.

TO REPLACE CAPS

1. Push cap into body so that single hash mark on cap lines up with the center seam on the back body of the unit.
2. Turn cap clockwise about 20° until the double hash marks on the cap line up with the center seam on the back body of the unit.

WARNING: To protect from excess lint, hair, etc., getting caught in motor, unit should never be used with the filter mesh removed. Injury or damage to unit could result.

LIMITED ONE YEAR WARRANTY

(U.S. and Canada Only)

Conair will repair or replace (at our option) your appliance free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed on back, together with your sales slip and $12.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period will be 12 months from the date of manufacture. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Please register this product at: www.conair.com/registration

SERVICE CENTER

Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
Visit us on the web at: www.conair.com

©2016 CONAIR CORPORATION
stock.image
BTS7
16PS020883

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>