Intermec PM23c Barcode Label Printer Installation Guide
- June 6, 2024
- Intermec
Table of Contents
PM23c
|PM43|PM43c
UART+Industrial Interface
Installation Instructions
Intermec Technologies Corporation
Worldwide Headquarters
6001 36th Ave.W.
Everett, WA 98203
U.S.A.
www.intermec.com
The information contained herein is provided solely for the purpose of
allowing customers to operate and service Intermec-manufactured equipment and
is not to be released, reproduced, or used for any other purpose without the
written permission of Intermec Technologies Corporation.
Information and specifications contained in this document are subject to
change without prior notice and do not represent a commitment on the part of
Intermec Technologies Corporation.
© 2012–2013 by Intermec Technologies Corporation. All rights reserved. The
word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook,
CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, INCA
(under license), i-logistics, Intellitag, Intellitag Gen2, JANUS, LabelShop,
MobileLAN, Picolink, Ready-to-Work, RoutePower, Sabre, ScanPlus, ShopScan,
Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista
Powered are either trademarks or registered trademarks of Intermec
Technologies Corporation. There are U.S. and foreign patents as well as U.S.
and foreign patents pending.
Install the UART+Industrial Interface Board
Use these instructions to install the UART+Industrial interface board in Intermec PM23c, PM43, and PM43c printers. You will find these items in the shipping box:
You will need the following tools to install the interface board:
- T20 Torx screwdriver
- Small wrench
To install the UART+Industrial interface board, you need to open the printer and physically install the board in the printer.
This board must only be installed by an authorized service technician.
Follow standard ESD guidelines to avoid damaging the equipment you are servicing.
Before you begin, turn off the printer and disconnect the power cord and communication cables.
The electronic compartment contains wires and components with dangerous voltage. Make sure that the printer is switched off and the power cord is disconnected before the cover is removed.
Open the Printer
You need to remove both the media coverage and the electronics cover to install the UART+Industrial interface board.
To remove the media cover
-
Open the media cover.
-
Use the small wrench to loosen the nut that secures the media cover latches in place.
-
Slide the latches counterclockwise into the open position.
-
Close the media cover and lift it off the hinges.
-
Put the media cover aside on a soft cloth to avoid scratches.
To remove the electronics cover
-
Use a T20 Torx screwdriver to remove the two screws that secure the electronics cover to the inside of the printer base.
-
Use a T20 Torx screwdriver to remove the two screws located on the outside of the electronics cover.
-
Remove the electronics cover, and put the cover aside on a soft cloth to avoid scratches.
To install the UART+Industrial interface board
-
On the back of the printer, remove the two screws that secure the cover plate to the printer, and remove the cover plate.
-
Attach the spacer screw to the center of the printer mainboard.
-
Insert the UART+Industrial interface board into the printer and use the T20 Torx screwdriver to secure the board assembly to the printer with the two Torx screws removed in Step 1.
-
Use the T20 Torx screwdriver to secure the interface board assembly to the spacer screw with a Torx screw.
-
Insert the single or dual option board cable into the 80-pin connector on the printer mainboard.
-
Insert the other end of the option cable into the 80-pin connector on the UART+Industrial interface board.
Note: You may need to use the dual option cable to connect to the mainboard depending on which slot you use for the UART+Industrial interface option board. -
Install the jumpers and ICs on the board to configure it for the type of serial communication you want to use:
To configure the board as Install these jumpers and ICs:RS-232| 1 Install a jumper on P3 so that the A is in the middle of the jumper.
2 Install IC, 360-028-001 (MAX238) on SKT3 with pin 1 located where the arrow points to SKT3 toward the bottom of the board.
RS-422| 1 Install jumpers on P4 and P5.
2 Install IC, 360-027-001 (MAX1490), across sockets SKT1 and SKT4 with pin 1 located where the arrow is pointing to SKT1 toward the bottom of the board.
RS-485| 1 Install a jumper on P2.
2 (Optionally) Install a jumper on P5 if this printer is going to be connected to the end of the cable.
3 Install IC, 360-026-001 (MAX1480), across SKT2 and SKT5 with pin 1 located where the arrow is pointing to SKT2 toward the bottom of the board.
- Replace the electronics cover.
- Replace the media cover.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
© 2013 Intermec Technologies
Corporation. All rights reserved.
PM23c, PM43, PM43c UART+Industrial Interface Installation Instructions
Documents / Resources
|
Intermec PM23c Barcode Label
Printer
[pdf] Installation Guide
PM23c, PM43, PM43c, Barcode Label Printer
---|---
|
Intermec PM23c Barcode Label
Printer
[pdf] Installation Guide
PM23c, Barcode Label Printer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>