Shark RV1000 Series Robot Vacuum Owner’s Manual
- June 6, 2024
- Shark
Table of Contents
Robot Vacuum
Aspirateur Robot
RV1000 Series
OWNER’S GUIDE
GUIDE D’UTILISATION
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY
If the charging cable plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. DO NOT force
into the outlet or try to modify it to fit.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
GENERAL WARNINGS
When using an electrical appliance, basic precautions should always be
followed, including the following:
-
A robotic vacuum cleaner consists of a robotic vacuum and charging base with a power supply. These components contain electrical connections, electrical wiring, and moving parts that potentially present risk to the user.
-
Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use.
-
Use only identical replacement parts.
-
This robotic vacuum cleaner contains no serviceable parts.
-
Use only as described in this manual. DO NOT use the robotic vacuum cleaner for any purpose other than those described in this manual.
-
With the exception of filters, DO NOT expose any parts of the robotic vacuum cleaner to water or other liquids.
-
USE WARNINGS This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
a) Children shall not play with the appliance.
b) Cleaning and user maintenance shall not be made by children without supervision. -
Always turn off the robotic vacuum cleaner before inserting or removing the filter or dust bin.
-
DO NOT handle plug, charging base, charging cable, or robotic vacuum cleaner with wet hands. Cleaning and user maintenance shall not be made by children without supervision.
-
DO NOT use without a robot dust bin and filters in place.
-
DO NOT damage the charging cord:
a) DO NOT pull or carry the charging base by the cord or use the cord as a handle.
b) DO NOT unplug by pulling on the cord. Grasp the plug, not the cord.
c) DO NOT close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces. -
DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
-
DO NOT use if robotic vacuum cleaner airflow is restricted. If the air paths become blocked, turn the vacuum cleaner off and remove all obstructions before turning on the unit again.
-
Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.
-
DO NOT use if robotic vacuum cleaners not working as they should, or have been dropped, damaged, left outdoors, or dropped into water.
-
DO NOT place vacuum cleaners on unstable surfaces.
-
DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects (glass, nails, screws, or coins)
b) Cleaning and user maintenance shall not be made by children without supervision.
d) Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.
e) Smoking or burning objects (hot coals, cigarette butts, or matches) f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene)
g) Toxic materials (chlorine bleach, ammonia, or drain cleaner) -
DO NOT use in the following areas:
a) Wet or damp surfaces
b) Outdoor areas
c) Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)
d) Near fireplaces with unobstructed entrances.
e) In an area with a space heater. -
Turn off the robotic vacuum cleaner before any adjustment, cleaning, maintenance, or troubleshooting.
-
Allow all filters to air-dry completely before replacing them in the robotic vacuum cleaner to prevent liquid from being drawn into electric parts.
-
DO NOT modify or attempt to repair the robotic vacuum cleaner or the battery yourself, except as indicated in this manual. DO NOT use the vacuum if it has been modified or damaged.
-
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plugin anyway.
-
In case the self-empty base has a thermal shutoff the unit needs to have a hard power reset to restart.
BATTERY USE -
The battery is the power source for the vacuum. Carefully read and follow all charging instructions.
-
To prevent unintentional starting, ensure the vacuum is powered off before picking up or carrying the vacuum. DO NOT carry the appliance with your finger on the
power switch. -
Use ONLY the Shark® self-empty base XSKDOCK100 and use only battery VBAT850. The use of batteries or battery chargers other than those indicated may create a risk of fire.
-
Keep the battery away from all metal objects such as paper clips, coins, keys, ails, or screws. Shorting the battery terminals together increases the risk of fire or burns.
-
Under abusive conditions, liquids may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes seek medical help.
-
A robotic vacuum cleaner should not be stored, charged, or used at temperatures below 50°F (10°C) or above 104°F(40°C). Ensure the battery and vacuum have reached room temperature before charging or use. Exposing the robot or battery to temperatures outside of this range may damage the battery and increase the risk of fire.
-
DO NOT expose the robotic vacuum cleaner or battery to fire or temperatures above 265°F (130°C) as it may cause an explosion.
BOTBOUNDARY™ STRIPS -
DO NOT put BotBoundary strips underneath the carpet or rugs.
-
DO NOT place BotBoundary strips on top of one another.
-
Always use BotBoundary strips around reflective flooring and surfaces.BotBoundary strips should always be used near carpeted stairs.
-
DO NOT place BotBoundary strips within 3 m (10 feet) of the dock.
-
For your robot’s cliff sensors to work properly, all runners, rugs, or carpets must be 20 cm (eight inches) from any stairs (or it must be continuous and extend over the edge of the stairs).
If a runner, rug, or carpet edge that is less than 20 cm (eight inches) from the stairs cannot be moved, you must use a BotBoundary strip to block off the stairs.
SAVE THESE INSTRUCTIONS
For the latest warnings and cautions, go to
sharkclean.com/robothelp
GETTING TO KNOW YOUR SHARK IQ ROBOT™
GETTING TO KNOW YOUR SHARK IQ ROBOT™
DOCK SETUP
NOTE: Select a permanent location for the Charging Dock, because every
time you relocate it, your robot will be required to completely re-map your
house.
NOTE : For best results, set up on the bare floor or thin carpet.
NOTE: Do not place dock against baseboards, heating elements, or in
direct sunlight.
Choose a level surface in a central area. Remove any objects that are closer
than 1 m (3 feet) from either side of the dock, or closer than 1.5 m (5 feet)
from the front of the dock. Place the dock with its back against the wall.
Plug the charging cord into an outlet. The indicator light on the dock will
illuminate green when the dock has power. The dock must be plugged in
continuously for the robot to find it.
INSTALLING THE SIDE BRUSHES
Snap the 2 included Side Brushes onto the square pegs on the bottom of the robot.sharkclean.com
CHARGING
IMPORTANT: The Shark IQ Robot™ has a pre-installed rechargeable battery. The
battery should be fully charged before use. It may take up to 6 hours to fully
charge.
To charge, the Power button on the side of the robot must be in the ON
position (I). The robot will beep when charging begins. When the cleaning
cycle is complete, or if the battery is running low, the robot will search for
the dock. If your robot doesn’t return to the dock, its charge may have run
out. 
If the robot has no charge and cannot return to the dock, manually place it on
the dock. The dock indicator light will flash blue and the robot will beep
when charging begins.
NOTE: When manually placing the robot on the dock, make sure the Charging
Contacts on the bottom of the robot are touching the ones on the dock. While
the robot is charging, both blue LED lights will flash. When charging is
complete, both blue lights will illuminate steadily.
NOTE: When picking up the robot, be careful not to place fingers between
the bumper and the base of the robot.
CHARGE INDICATOR LIGHTS
The blue indicator lights on the robot shows how much charge is remaining.
While the robot is charging, both blue LED lights will flash. When charging is
complete, both blue lights will illuminate steadily. It may take up to 6 hours
to fully charge your robot.
CLEAN BUTTON Press to begin a cleaning session. Press again to stop.
RECHARGE & RESUME
Press and hold the CLEAN button for 15 seconds to turn Recharge & Resume ON or
OFF.
The Recharge & Resume function is turned OFF by default. Turn ON Recharge &
Resume for complete coverage if your home’s floor plan is larger than 140 m 2
Your robot will return to the base, recharge, and can pick up cleaning where
it left off.
DOCK BUTTON Press to stop cleaning and send the robot back to the
charging dock.
CHARGE INDICATOR LIGHTS
Display the amount of charge remaining in the battery.
“!” ERROR INDICATOR
See the Troubleshooting section for a full list of error codes.
WI-FI INDICATOR
Blue
light: connected to Wi-Fi. Red light: not connected. Flashing blue: setup
mode. No light: not set up yet.
NAVIGATION MODULE
Please keep clear and do not cover. Upward-facing sensor aids advanced
navigation.
NOTE: If the low charge light is blinking red, there is not enough charge
for the robot to return to the dock. Manually place the robot on the dock.
PREP YOUR HOME
Your robot uses an array of sensors to navigate around walls, furniture
legs, and other obstacles while it cleans. To prevent the robot from bumping
into objects or navigating to areas you don’t want it to, use the included
BotBoundary™ strips. For best results, prepare your home as indicated below,
and schedule a daily cleaning to ensure all floor areas are regularly
maintained.
NOTE : Scheduling is one of many features that are only available in the
app.
OBSTRUCTIONS Clear cords and small objects from floors and open interior doors to ensure a complete map of your home.
THRESHOLDS ****
Your robot may have trouble clearing some thresholds higher than 2.2 cm (7/8″). Block off high thresholds with the included BotBoundary™ strips.
STAIRS
Your
robot’s cliff sensors will prevent it from falling off ledges. For the cliff
sensors to work properly, all runners, rugs, or carpets must be at least 20
cm (8 inches) from any stairs (or extend over the edge of the stairs.)
SCHEDULING
For a constant state of clean, set up a whole-home cleaning schedule in the
app.
AVOID MOVING THE ROBOT & DOCK
While your robot is cleaning, do not pick it up and move it to different rooms, or move the charging dock this could impact the robot’s navigation.
IMPORTANT: Before cleaning an entire room for the first time, we recommend that you first test your robot on a small section of the floor to ensure there is no scratching.
USING THE SHARK IQ ROBOT™Shark
IQ NAVIGATION™ Control Schedule History 
As it cleans, your robot will create a map of your home. It may take several cleanings for the robot to finish its mapping. Once the mapping is complete, an Interactive Map of your floor plan will be available on the app.
EDIT OPTIONS RUMPELSTILTSKIN
Interactive Map
The interactive map in the app allows you to name rooms, then select which
rooms to clean, and end the robot to immediately clean one specific location.
As cleanings continue, the robot will update and refine its path to provide
optimized cleaning coverage. After each use, a cleaning report will be
available in the app.
USAGE INSTRUCTIONS
1. You can cut BotBoundary strips to shorten them as needed. (.5 m/18-inch
minimum) If cutting a strip, make sure it’s still long enough to cover the
entire area you need to block off. Gaps may cause BotBoundary strips to
malfunction.
2. Make sure each BotBoundary strip lies completely flat against the floor,
with no overlapping. NOTE: DO NOT place BotBoundary strips on top of one
another.
3. For best results, place the strips between fixed objects like furniture
legs or door frames, or make a closed loop around an obstacle.
PREPPING YOUR HOME USING BOTBOUNDARY STRIPS
Use the BotBoundary strips to quickly and easily create no-go zones to keep
your robot out of the areas you would like it to avoid. These may include:
• Near power cords
• In front of thresholds higher than 2.2 cm (7/8″)
MANUAL CLEANING MODE
To manually start a cleaning cycle, press the Clean button on the robot or on
the mobile app. To stop the robot before it finishes cleaning and
automatically returns to the dock, press the Dock button.
NOTE: Be sure to charge the robot completely before its first cleaning so
that it can explore, map, and clean as much of your home as possible. It may
take up to 6 hours to fully charge your robot.
NOTE: Avoid picking up or moving the robot or dock. If either is
relocated, the robot may not be able to follow its intelligent cleaning path
or find its way back to the dock. If the robot is picked up or moved for any
reason, it should be returned to within 15 cm (6 inches) of its last location.
Please visit sharkclean.com/app or call
1-888-228-5531 for answers to all your
app questions.
USING THE SHARKCLEAN™ APP AND VOICE CONTROLS
Get the most out of your Shark IQ Robot™ with these app features:
Interactive Map Your robot knows where it is in your home. Identify rooms for
Room Select.
Room Select Immediately send your robot directly to any room on that floor.
Recharge and Resume Use Recharge and Resume to help ensure complete, multi-
room coverage in your home.
EDITOPTIONS RUMPELSTILTSKIN
Scheduling
Set whole-home cleanings for any time, any day.
Control From Anywhere
Wherever you are, you’re in control of your robot.
Cleaning Reports
Each time your robot cleans, your app will generate a cleaning report.
Volume Control
You can adjust the volume level of your robot’s audio notifications.
Search for SharkClean in the app store and download the app to your iPhone TM
or Android TM
.
SETTING UP VOICE CONTROL WITH THE GOOGLE ASSISTANT OR AMAZON ALEXA
Visit sharkclean.com/app for setup instructions which include how to enable
Shark Skill for Amazon Alexa and using with Google Assistant.
Google Assistant:
“OK Google, tell Shark to start cleaning.”
“OK Google, tell Shark to pause my robot.”
“ OK Google, tell Shark to send my robot to the dock.”| Amazon Alexa:
“Alexa, tell Shark to start cleaning.”
“Alexa, tell Shark to pause my robot.”
“ Alexa, tell Shark to send my robot to the dock.”
---|---
WI-FI TROUBLESHOOTING
• To use the app, your phone must be connected to a 2.4GHz network. The app
will only work on a 2.4GHz network.
• Typical home Wi-Fi networks support both 2.4GHz and 5GHz.
• Do not use a VPN or a proxy server.
• Make sure Wi-Fi isolation is turned off on the router.
• If you cannot connect, call
1-888-228-5531.
STILL CAN’T CONNECT?
Restart your phone Reboot your robot
• Press the power button on the side of the ROBOT to the OFF position, for 10
seconds then press it again to turn the power back ON.
Reboot your router
• Unplug the router power cable for 30 seconds, then plug it back in. Allow
several minutes for your router to reboot completely. STILL CAN’T CONNECT?
ERROR CODE PROBLEM
(RED) * WI-FI Indicator (RED nestling)Wrong password for Wi-fi
I (Flashing red) • WI-Fl (RED)SSID cannot be found. try connecting again
t• WPM (Flashing RED alternately) Wrong user name or password for your Shark
account
1 • Wifi (EtasNag RED at the same time) Cannot connect to Wi-fi
MAINTENANCE
CAUTION: Turn off power before performing any maintenance.
EMPTYING THE DUST BIN
Press the Dust Bin Release Tab and slide out the dust bin. To avoid spills, be
sure to hold the dust bin in an upright position. Use the finger slots to open
the lid.
Empty debris and dust into trash. Look between the filter and plastic shield
and make sure there is no debris buildup. Remove the shield and clear any
debris buildup as needed with a dry cloth or soft brush.
NOTE: Make sure to insert the dust bin completely, until it clicks into place.
MAINTENANCE
CLEANING AND REPLACING THE FILTER
For optimal suction power, regularly clean and replace the filter inside the
robot’s dust bin. See sharkaccessories.com for replacement filters.
IMPORTANT: DO NOT use water when cleaning the filter.
Remove and empty the dust bin. Clean any hair or debris off the Anti-Tangle
Comb on the back of the dust bin. Pull the filter out of the dust bin by the
tabs. 
Lightly tap the filter to remove dust and debris Reinsert the filter into the
dust bin, then slide the dust bin back into the robot.
NOTE : Make sure to insert the dust bin completely, until it clicks into
place.
SELF-CLEANING BRUSH ROLL
the Self-Cleaning Brushroll actively removes hair wrap while your robot
cleans. If some debris remains wrapped around the brush roll, continue
cleaning to allow the brush roll to clean itself. 
To access the brush roll, push up on the tabs on the brush roll access door, then lift off the door. Lift out the brush roll and clean off any debris. Reinstall the brush roll, inserting the flat end first. Close the brushroll access door and press down until both sides click into place.
NOTE : Replace brushroll every 6 to 12 months, or when visibly worn. See
sharkaccessories.com for replacement parts.
NOTE: When cutting away debris, be sure not to cut the brush roll.
CLEANING SENSORS AND CHARGING PADS
CLEAN SENSORS AND CHARGING PADS AS NEEDED. With a dry cloth, gently dust
off the sensors and pads located on the bottom of the robot and on the
dock.
IMPORTANT : The robot uses cliff sensors to avoid stairs and other steep drops. Sensors may work less effectively when they are dirty. For best results, clean sensors regularly.
CLEANING THE WHEELS CLEAN THE FRONT WHEEL PERIODICALLY.
See sharkaccessories.com for replacement parts. 
Clean the wheel housing. Periodically clean the drive wheels and the housing around them. To clean, rotate each drive wheel while dusting.
CLEANING SIDE BRUSHES CLEAN SIDE BRUSHES AS NEEDED.
Carefully unwind and remove any string or hair wrapped around brushes. Gently
wipe brushes with a dry cloth. To reinstall, snap the brushes over the pegs.
Spin the brushes
manually to make sure they are installed correctly.
NOTE: Remove and replace any side brushes that are bent or damaged. To
remove a brush, lift it off its peg. 
MAINTENANCE
CAUTION: Turn off power before performing any maintenance.
TROUBLESHOOTING
If any error lights are illuminated or flashing on your Shark IQ Robot™,
see the error code chart below:
ERROR CODE| ERROR
NUMBER| SOLUTION
---|---|---
CLEAN (RED) +! (RED) flashing| 3| Suction motor failure. Remove and empty
the dust bin, clean the filters. and remove blockages to ensure nothing is
reducing suction.
CLEAN (RED) flashing| 10| A robot may be stuck on an obstacle. Move the
robot to a new location on a level surface.
DOCK (RED) flashing| 6| The front bumper may be jammed. Clean the bumper
and make sure it moves in and out freely.
CLEAN (BLUE) + DOCK (RED) solid| 14| BotBoundary’s error. Move your robot
to a flat surface away from the magnetic boundary strip and try cleaning
again.
CLEAN (RED) + DOCK (BLUE) flashing| 7| Cliff sensor error. Move your
robot to a new location and clean its cliff sensors.
CLEAN (RED) + DOCK (RED) flashing| 9| The robot dustbin has been removed
and needs to be reinserted.
DOCK (RED) + ! (RED) flashing| 2| The side brush is stuck. Remove
any debris from around the side brushes.
CLEAN (RED) + DOCK (RED) + ! (RED) flashing| 2| A drive wheel is
stuck. Clean the wheels and remove any debris wrapped around the axles.
CLEAN (RED) + DOCK (BLUE) alternating| 16| The robot is stuck. Move your
robot to a new location and make sure the front bumper moves in and out
freely.
CLEAN (BLUE) + DOCK (RED) +! (RED) flashing| 2| Wheel motor encoder
failure. Please contact Shark Customer Care at
1-800-798-7398.
CLEAN (BLUE) +! (RED) flashing| 2| Blockage in the brush roll. Remove any
debris from around the brush roll.
CLEAN (RED) + DOCK (BLUE) +! (RED) flashing| 21| The robot has
encountered an error while booting. Please turn the power off and back on.
CLEAN (BLUE) + DOCK (RED) flashing| 23| The robot cannot locate the dock.
Please pick up your robot and place it on the dock.
BATTERY ICON (RED) flashing| 24| The battery is critically low and needs
recharging. Power may be turned off or the battery may need charging.
CLEAN (RED) +! (RED) alternating| 2| Blockage in the brush roll. Remove
any debris from around the brush roll.
NOTE : To order replacement parts and filters, visit sharkaccessories.com.
END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE
IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT
CAREFULLY BEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS
PRODUCT : SharkNinja Operating LLC’s (“SharkNinja”) End-User License
Agreement (“EULA”) is a legal agreement between You (either a single entity or
an individual) and SharkNinja for SharkNinja’s Software Applications,
including those installed by You onto your SharkNinja products or already
installed on your device, including all firmware(referred hereafter as “SN
APPS”). By installing, copying, checking a box, clicking a button confirming
your agreement to these terms, or otherwise continuing to use the SN APPS, You
agree to be bound by the terms of this EULA. This license agreement represents
the entire agreement concerning SN APPS between You and SharkNinja, and it
supersedes any prior proposal, representation, or understanding between the
parties. If You do not agree to the terms of this EULA, do not install or use
the SN APPS or this product. The SN APPS are protected by copyright laws and
international copyright treaties, as well as other
intellectual property laws and treaties.
GRANT OF LICENSE. The SN APPS are licensed as follows:
Installation and Use. SharkNinja grants You the right to download, install,
and use SN APPS on the specified platform for which the SN APP was designed
and in connection with SharkNinja products with which the SN APPS are designed
to operate (“SN Devices”).
Backup Copies. You may also make a copy of SN APPS downloaded and installed by
You for backup and archival purposes.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
Maintenance of Copyright Notices. You must not remove or alter any copyright
notices on any and all copies of the SN APPS.
Distribution. You may not distribute copies of the SN APPS to third parties.
Prohibition on Reverse Engineering, Decompilation, and Disassembly. You may
not reverse engineer, decompile, or disassemble SN APPS, except and only to
the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation.
Rental. You may not rent, lease, or lend SN APPS without written permission
from SharkNinja.
NOT FOR RESALE SOFTWARE. Applications identified as “Not for Resale” or “NFR,”
may not be resold, transferred, or used for any purpose other than
demonstration, test, or evaluation.
Support Services. SharkNinja may provide You with support services related to
SN APPS (“Support
Services”). Any supplemental software code provided to You as part of the
Support Services shall be considered part of SN APPS and subject to the terms
and conditions of this EULA.
Compliance with Applicable Laws. You must comply with all applicable laws
regarding the use of SN APPS.
UPDATES. SharkNinja may provide You with upgrades or updates to SN APPS.
This EULA will govern any upgrades provided by SharkNinja that replace and/or
supplement SN APPS unless such upgrade is accompanied by a separate EULA, in
which case the terms of that EULA will govern. If You decide not to download
and use an upgrade or update provided by SharkNinja, You understand that You
could put SN Apps at risk of serious security threats or cause SN Apps to
become unusable or unstable.
4. DATA AND PRIVACY. SharkNinja is committed to ensuring your privacy by
adhering to high standards of fairness and integrity. We are committed to
keeping our customers informed about how we use the information we gather from
You through the use of each of our websites or SN APPS. Our privacy practices
are described in SharkNinja’s Privacy Policy, as well as in separate notices
given when an app, product, or service is purchased or downloaded. By using SN
APPs or providing us with your personal information, You are accepting and
consenting to the practices, terms, and conditions described in SharkNinja’s
Privacy Policy. At all times your information will be treated in accordance
with the SharkNinja Privacy Policy, which is incorporated by reference into
this EULA and can be viewed at the following
URL:http://[www.sharkninja.com/privacypolicy.](http://www.sharkninja.com/privacypolicy.)
THIRD-PARTY APPLICATION LIBRARIES AND EMBEDDED SOFTWARE.
You acknowledge that Ayla Networks, Inc. (“Ayla”) has provided certain
application libraries that have been embedded into SN APPS (“Ayla Application
Libraries”) and enables SN Devices to connect to the Ayla Cloud Service (“Ayla
Embedded Software”).
You will not use the Ayla Application Libraries except as an incorporated
portion of SN APPS, unmodified from the form provided to You.
You will not use the Ayla Embedded Software except as an incorporated portion
of SN Devices, unmodified from the form provided to You.
You will not modify, adapt, translate, or create derivative works based on, or
decompile, disassemble, reverse engineer, or otherwise attempt to derive the
source code or underlying algorithms of, the Ayla
Application Libraries or the Ayla Embedded Software.
SharkNinja retains all ownership of SN APPS (and the Ayla Application
Libraries contained therein) and any software installed on SN Devices
(including the Ayla Embedded software) and only a license thereto is granted
to You for use in connection with the SN APPS and SN Devices.
END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE
You will not use the Ayla Application Libraries or Ayla Embedded Software to
attempt to gain unauthorized access to or use of the systems/services of
SharkNinja’s other licensors; nor will You transmitviruses, worms, Trojan
horses, time bombs, spyware, malware, cancelbots, passive collection
mechanisms, robots, data mining software, or any other malicious or invasive
code or program into the systems/services of SharkNinja’s other licensors.
You will not use the Ayla Application Libraries or Ayla Embedded Software to
interfere with, breach, or circumvent any security feature, authentication
feature, or any other feature that restricts or enforces limitations on the
use of, or access to, the systems/services of SharkNinja’s other licensors.
You will not probe, attack, scan or test the vulnerability of the
systems/services of SharkNinja’s other licensors.
SharkNinja’s other licensors of the SN APPS, Ayla Application Libraries, and
the Ayla Embedded Software are the express third-party beneficiaries of this
EULA, and the provisions of this Section of this EULA are made expressly for
the benefit of such licensors and are enforceable by such licensors.
TERMINATION. Without prejudice to any other rights, SharkNinja may
terminate this EULA if You fail to comply with the terms and conditions of
this EULA. In such an event, You must destroy all copies of SN APPS in your
possession.
COPYRIGHT. All titles, including but not limited to copyrights, in and to
SN APPS and any copies thereof are owned by SharkNinja or its suppliers. All
title and intellectual property rights in and to the content which may be
accessed through the use of SN APPS are the property of the respective content
owner and may be protected by applicable copyright or other intellectual
property laws and treaties. This EULA grants You no rights to use such
content. All rights not expressly granted are reserved by SharkNinja.
OPEN SOURCE SOFTWARE. You hereby acknowledge that SN APPS may contain
software that is subject to “open source” or “free software” licenses (“Open
Source Software”). The license granted by this EULA does not apply to Open
Source Software contained in the SN APPS. Rather, the terms and conditions in
the applicable Open Source Software license shall apply to the Open Source
Software. Nothing in this EULA limits your rights under, or grants You rights
that supersede, any Open Source Software license. You acknowledge that the
Open Source Software license is solely between You and the applicable licensor
of the Open Source Software. To the extent the terms of the licenses
applicable to the Open Source Software require SharkNinja to provide the Open
Source Software, in either source or executable form, or to provide copies of
applicable license terms or other required information, You may obtain a copy
of the software by contacting SharkNinja at the below physical address.
Additional information about the Open Source Software, and its terms of use,
may be found at www.sharkclean.com/opensource.
NO WARRANTIES. SharkNinja expressly disclaims any warranty for SN APPS,
Ayla Application Libraries, or Ayla Embedded Software. SN APPS, Ayla
Application libraries, and Ayla Embedded Software are provided ‘As Is’ without
any express or implied warranty of any kind, including but not limited to any
warranties of merchantability, noninfringement, the fitness of a particular
purpose, or title. SharkNinja does not warrant or assume responsibility for
the accuracy or completeness of any information, text, graphics, links, or
other items contained within the SN APPS. SharkNinja makes no warranties
respecting any harm that may be caused by the transmission of a computer
virus, worm, logic bomb, or another such computer program. SharkNinja further
expressly disclaims any warranty or representation to any third party.
LIMITATION OF LIABILITY. In no event shall SharkNinja or its suppliers be
liable for any special, incidental, punitive, indirect, or consequential
damages whatsoever (including, but not limited to, damages for loss of profits
or confidential or other information, for business interruption, for personal
injury, for loss of privacy, for failure to meet any duty including of good
faith or of reasonable care, for negligence, and for any other pecuniary or
other loss whatsoever) arising out of or in any way related to the use of or
inability to use SN Devices or SN APPS, the provision of or failure to provide
support or other services, information, software, and related content through
the product or otherwise arising out of the use of SN APPS, or otherwise
under or in connection with any provision of this EULA, even in the event of
the fault, tort (including negligence), strict liability, breach of contract,
or breach of warranty of SharkNinja or any supplier, and even if SharkNinja or
any supplier has been advised of the possibility of such damages. SharkNinja
shall have no liability with respect to the content of the SN APPS or any part
thereof, including but not limited to errors or omissions contained therein,
libel, infringements of rights of publicity, privacy, trademark rights,
business interruption, personal injury, loss of privacy, moral rights, or the
disclosure of confidential information.
APPLICABLE LAW. The laws of the Commonwealth of Massachusetts will govern
this EULA and You hereby consent to exclusive jurisdiction and venue in the
state and federal courts sitting in the Commonwealth of Massachusetts.
ASSIGNMENT. SharkNinja may assign this EULA without notice to Licensor.
ENTIRE AGREEMENT. This EULA (including any addendum or amendment to this
EULA which is included with the SN Devices) is the entire agreement between
You and SharkNinja relating to the SN APPS and supersedes all prior or
contemporaneous oral or written communications, proposals, and representations
with respect to the SN APPS or any other subject matter covered by this EULA.
To the extent, the terms of any SharkNinja policies or programs for support
services conflict with the terms of this
EULA, the terms of this EULA shall control. If You have questions regarding
this EULA, please contact SharkNinja at 89 A Street, Suite 100, Needham, MA
02494.
ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja Operating LLC. Warranty coverage applies to the
original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of one (1) year from the date of purchase when it is
used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable components deemed defective, in
SharkNinja’s sole discretion, will be repaired or replaced up to one (1) year
from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six
(6) months following the receipt date of the replacement unit or the remainder
of the existing warranty, whichever is later. SharkNinja reserves the right to
replace the unit with one of equal or greater value.
What is not covered by this warranty?
- Normal wear and tear of wearable parts (such as foam filters, filters, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
- Any unit that has been tampered with or used for commercial purposes.
- Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit.
- Consequential and incidental damages.
- Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja
- Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty period, visit sharkclean.com/support
for product care and maintenance self-help. Our Customer Service Specialists
are also available at 1-888-228-5531 to
assist with product support and warranty service options, ncluding the
possibility of upgrading to our VIP warranty service options for select
product categories. Please register your product and have it with you when
contacting Customer Service. SharkNinja will cover the cost for the customer
to send in the unit to us for repair or replacement. A fee of $24.95 (subject
to change) will be charged when SharkNinja ships the repaired or replacement
unit.
How to initiate a warranty claim
You must call 1-888-228-5531 to
initiate a warranty claim. You will need the receipt as proof of purchase. A
Customer Service Specialist will provide you with return and packing
instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you.
REGISTER YOUR PURCHASE registeryourshark.com
FCC WARNINGS
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to parts 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following conditions:
1 This device may not cause harmful interference
2 This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
RECORD THIS INFORMATION
Model Number:
Date Code:
Date of Purchase:
Store of Purchase
TIP: You can find the model and serial numbers on the QR code labels on the
bottom of the robot and battery.
EXPECTED PERFORMANCE
Expected Runtime: 60 minutes
Expected charging time: 6 hours
BATTERY REMOVAL AND DISPOSAL
This product uses a battery. When the battery no longer holds a charge, it
should be removed from the vacuum and recycled. DO NOT incinerate or
compost the battery.
When your lithium-ion battery needs to be replaced, dispose of it or recycle
it in accordance with local ordinances or regulations. In some areas, it is
illegal to place spent lithium-ion batteries in the trash or in a municipal
solid waste stream. Return spent battery to an authorized recycling center or
to the retailer for recycling. Contact your local recycling center for
information on where to drop off the spent battery.
For more information on battery removal for disposal, please visit
sharkclean.com/batterysupport.
The RBRC™ (Rechargeable Battery Recycling Corporation) seal on the lithium-ion
battery indicates that the costs to recycle the battery at the end of its
useful life have already been paid by SharkNinja. In some areas, it is illegal
to place spent lithium-ion batteries in the trash or municipal solid waste
stream and the RBRC program provides an environmentally conscious alternative.
RBRC, in cooperation with SharkNinja and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent
lithium-ion batteries. Help protect our environment and conserve natural
resources by returning the spent lithium-ion battery to an authorized
SharkNinja service center or to your local retailer for recycling. You may
also contact your local recycling center for information on where to drop off
the spent battery, or call
1-800-798-7398.
PLEASE READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you keep your Shark IQ Robot™ running
at peak performance.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-888-228-5531
sharkclean.com
Illustrations may differ from the actual product. We are constantly striving
to improve our products; therefore the specifications contained herein are
subject to change without notice. For SharkNinja U.S. Patent information,
visit sharkninja.com/uspatents
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>