LASER T4P-4GPETTRAC 4G Pet Tracker User Manual

: June 6, 2024
: Laser

LASER T4P-4GPETTRAC 4G Pet Tracker

PACKAGE CONTENTS

1 x 4G Smart Pet Tracker
1 x Collar Case
1 x Charge Cable
1 x User Manual

Note: USB Adaptor and SIM Card are not included

SETTING UP THE TRACKER

Install a standard Nano SIM card (4G SIM for LTE network) according to the SIM card installation method. The SIM card needs to enable voice, SMS, data services and caller ID service.

Remove the 2 screws then you can use the SIM card pin tool to remove the cover (please be careful not to damage the coating).

SIM CARD INSTALLATION METHOD

Insert a suitable 4G Nano SIMcard with the gold side facing upwards and the diagonal corner facing the bottom right corner of the tracker.

Remove the 2 screws then you can use the SIM card pin tool to remove the cover (please be careful not to damage the coating).

Power On:
Press and HOLD the power button until the motor vibrates.

Power Off:
Tap the power button 10 times continously (within 5 seconds).

Reboot:
Press the power button for 15 seconds, the tracker will reboot

Charging the Battery:
Use the magnetic charging lead and attach to the back of the tracker, connect the other end of the cable to a USB charger 5V 1A / 5V 2A to charge.

Note:

| Please do not use a fast charger with a 9V output.
A voltage higher than 5V may damage the device.
---|---

APN SETTINGS

The APN settings are not required for most mobile providers but if you have just purchased a new SIM you may need to follow these instructions to set it
up:

To test you can send below SMS command to check if there is APN problem:
pw,123456,ts#
You will get SMS reply that includes following:
wifiOpen:
wifiConnect:
gprsOpen:
NET:OK(100)

To carry out the configuration, Google from the provider’s official website, or insert SIM card into an Android phone and check the network profile to find out:

APN name
Username:
(most operators in the world do not require it)
Password:
(most operators in the world do not require it)
MCC:
Mobile Country Code
MNC:
Mobile Network Code – Operator Code
For example, the MCC code for Australia is 505.

For mobile operators who do not require user name and password as authentication, the username and password values should be left blank (just replace with commas).

With this data, we can manually configure the APN by sending the following SMS message to the SIM number in the device (by entering the specific values of the Operator):

pw,123456,apn,APN name,username,password,PLMN#

Example 1:

APN name: telstra.internet
Username:
Password:
MCC:505
MNC: 01

The SMS command to be sent to the SIM number in the GPS Tracker is pw,123456,apn,telstra.internet,,,50501#

MNC needs to be no less than 2 digits, for example 02 instead of 2.

Example 2:

APN name: tmobil.cl
Username: wap
Password: wap
MCC:730
MNC: 2

The SMS command to be sent to the SIM number in the GPS Tracker is pw, 123456, apn,tmobil.cl,wap,wap,73002#

SMS command should all be lower case letters without spaces. After sending the sms command, you will get an sms reply ‘set apn.. is successful’. Now please restart the tracker.

TRACKER DIAGRAM

Note:
If the GPS tracker fails to turn on correctly, use the “Reset” button. After pressing the “Reset” button, the GPS tracker system will be forcibly turned off, and the settings will remain unchanged.Please charge the GPS tracker battery after the unit has turned off to get the tracker back to normal operation.

USING THE APP

Option 1

Scan the following QR code, download and install the App

Option 2

Search “SeTracker” in App Store – Apple or Google Play

Note:
During installation, the phone prompts whether to trust the APP or whether to allow prompt access to the phone’s location, etc. Please select trusted and allow all the time.

REGISTERING THE TRACKER AND LOGGING IN

Open the App; new users will need to register a new account by clicking on the bottom right “Register” button and complete the registration steps.

Please note that you will need to select the right area you are located in, for example if you’re in Australia, you need to select “Area” as “Asia and Oceania”.

You also need to input a correct email address to ensure you can reset your password if needed.

To avoid malicious registration, one mobile phone cannot register more than 5 accounts.

CONNECTING THE GPS TRACKER TO YOUR APP ACCOUNT After

successful registration, log in to the account, under Add Device select “Please Scan” option.
Use the phone’s camera to scan the QR code on the back of the Tracker.

TIP:
The Registration QR code is the 15-digit registration number found on the QR sticker on the back of the tracker (it is not the IMEI barcode number).

ADDING OR DELETING THE DEVICE

How to add the device to your account:
ME > Device list > Add device > put the registration code of Tracker.
How to delete the device from your account: ME > Device list > Edit > Delete > OK

ADDING A SECONDARY USER ACCOUNT

Follow previous steps on another phone to register a new account and scan the QR code on the back of the tracker to add the device. The original administrator account will receive a notification to add the second user.

Note:
One APP account can bind multiple GPS trackers. One GPS tracker can also be connected with numerous secondary accounts with authorization from the primary administrator.

APP FEATURES

LOCATION UPDATE SETTING

This setting determines how often data is updated from the Tracker to the APP. In the APP select ME > Location Update Schedule
NOTE: If the GPS tracker keeps still without movement, it will not update location to save battery. If GPS Tracker is not connected to a network then no location data can be sent to the APP.

LOCATION UPDATE SETTING

This feature helps track the location history of the tracker.
In the APP select MAP > HISTORY icon to check the location history.

GEO-FENCING

The Geo-fence feature sends a push notification if the tracker has left the safe zone. This feature requires GPS interval setting in mode 0, which is the standard mode.
In the APP select MAP > Geo-fence icon to check the location history.

Next tap the PLUS icon then tap the screen in the area you want to set the Geo-fence around.
Give the Geo-fence a name.
Set the Geo-fence perimeter.

SOS CALLING MODE

The SOS calling feature can help find a lost pet. In case of emergency, long- press the SOS button on the tracker to trigger the emergency call SOS. At this time, the tracker will call the 3 preset emergency numbers in order.
In the APP select
ME > SOS Number – Enter SOS phone numbers Tap Save
Medication Reminders:
In the Home screen of the APP you can set a medication reminder.

PRECAUTIONS

Do not immerse the product in liquid or chemicals such as salty water and detergents
Do not wear the product in the shower, in case of damage from products like shower gel, shampoo, conditioner, hot water etc.
Keep the product away from fire, heat and other extreme high- temperature environments.
Use only 5V chargers or USB ports, because higher voltage may damage the device.
Do not directly attach the magnetic charging lead to any metal or conductive objects except the GPS Tracker; otherwise, it may cause the charging head to short circuit
In the case of excessive heat of the battery during charging, immediately disconnect it from the power supply.
Before first use, fully charge the battery. · If the tracker heats up when wearing it, immediately take it off and power down the tracker via the App.
Never connect to a mechanically damaged charger or if the batteries are swollen. Do not use batteries in this condition due to risk of explosion.
When this product is in a de-energized state, and outside the service area, the location function

For more For more helpful guides visit us at

LASER www.youtube.com/LasercoAu