wwio TRINITY T2 TV Stick Instruction Manual

TRINITY T2 TV Stick

A complete version of the User Manual can be found here: www.wwio.de/support

Safety Instructions

• Before starting the device, please check the unit operating voltage.
  The correct voltage is printed on the identification plate.

• The T2 TV Stick is powered through a USB port. Make sure the USB port is able to provide the required output current printed on the T2
  TV Stick. In case you plug in additional USB devices to the supplied USB cable, the USB port needs to deliver additional power.

• The receiver shall not be exposed to dripping or splashing water, and no objects filled with liquids, such as a vase, shall be placed on the
  apparatus. Indoor use only!

• Plug out the receiver from the wall outlet before cleaning.

• Clean the receiver with a soft cloth (no solvents).

• In order to prevent damage to property or personal injuries and grant a smooth operation hire a specialized company to carry out the installation of outdoor antennas.

• Avoid heat build-up inside the receiver. (Free distance around the product: 10 cm min.)

• Never perform repairs and installations yourself. Refer all servicing to qualified service personnel.

• The unit heats up in service. This is normal and not a malfunction.

Usage
This device is designed to be used in private households and closed rooms.

Operating Conditions

USB Port
The USB port on the USB cable supplied enables you to attach a USB stick in order to update the receiver software. The USB port is not to supposed be used for other purposes.

Batteries for the Remote Controller

• Remove old batteries as leakage may damage the remote control.
• In case of the battery, leakage uses a cloth to remove the battery fluid be careful to avoid skin contact.
• In case the battery’s contents are ingested, drink water to dilute the battery material and seek immediate medical attention.
• If the eyes or skin come into contact with these substances immediately flush with water and seek immediate medical attention.
• Keep batteries and remote control away from children.

EC Declaration
Hereby, WWIO Elektronik GmbH declares that the following Radio Equipment:

• WWIO TRINITY T2 TV Stick is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.wwio.de/support

Contact Address in EU: WWIO Elektronik GmbH, Theodor Heuss Str. 14C, 21629 Neu Wulmstorf, Germany
Recycling of electronic devices
This product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling center. In the European Union, there are separate collection systems for used electrical and electronic products. Please, help us to conserve the environment we live in!

Recycling of paper and cardboard
The material recycling symbol on the package and user manual denotes that they are recyclable. Do not dispose of them with normal household waste.
Batteries
Every user is legally obliged to dispose of batteries at a local authority collection point or in a shop so that they can be disposed of in an environmentally-friendly way. Do not dispose of them in household waste.

WWIO-Customer Service
Please contact your Retailer for Service and Support.
You may also contact the WWIO-customer service in Germany.
E-Mail:support@wwio.de
Internet: www.wwio.de/support

Installation

1. Attach the adapter onto the antenna jack [5].

2. Connect the antenna cable with the antenna jack.

3. Connect the remote control IR-receiver with the jack [3]. Place the IR receiver in front of your TV.
   The receiver needs to be in direct line of sight of the remote control.

4. The HDMI stick [4] can be directly connected to the TV. If there is too little space use the HDMI extension cord supplied.

5. Insert the USB connection cable into the USB port [1]. Attach the other end with a free USB port on your TV. The stick is switched on as soon as power is supplied. The LED [2] switches on.

If the power supply LED stays dark there is no sufficient energy supply for the stick.

In that case, try to connect the USB cable with another USB port. In case your TV only has one USB port using an external power supply unit with a USB outlet (5 V, min. 1000 mA) instead. Appropriate power supply units are available from specialist stores.

Remote Control – Batteries

•  Insert the batteries (1,5V size AAA) in the compartment on the back of the remote control. Insert the batteries, taking care to match the polarity, as indicated in the battery compartment and on the batteries.
• If the receiver is not in use for a longer period of time, remove the batteries from the remote control.

Remote Control – Keys
POWER: Switches the device on/off (standby)
Mute: Mute audio
EPG: Display electronic program guide
TTX: Display Teletext
SUB-T: Subtitles on/off
PAGE: Scroll through lists page by page
AUDIO: Switch audio tracks
MENU: Display the main menu
EXIT: Cancel/exit
▲/▼/◄/►/CH+/CH- /VOL-/VOL+: Navigation keys, next/previous channel, Increase/decrease volume
OK: Confirm selection, Show channel list
FAV: Show favorite lists
TV/RADIO: Switch from TV to radio mode 0-9: Numeric keys
RECALL: Go to the previous channel
i/INFO: Display information
RED: Red function key
GREEN/V-FORMAT : Green function key, set HDMI resolution
YELLOW/ASPECT: Yellow function key, change the aspect ratio
BLUE: Blue function key

First Time Installation
If everything is connected properly, the right signal source has been selected and the power supply LED on the receiver stick lights up, you will see the following installation menu on the TV screen. Use the arrow keys ▲/▼ to navigate among menu items. If a menu item is highlighted you can use the ◄/► keys to make changes.

OSD Language:
Set the OSD language.
Country
Select the country in which the receiver is to be operated.
Antenna Power
In case your antenna needs to be supplied with power (e.g. an indoor antenna with an amplifier but no power supply unit) by your receiver you need to activate this function in the menu.
Channel Search
Initiate the scan mode by pressing OK. It can take a couple of minutes to complete the scan. In case not all channels appear in the list after the scan
you need to readjust the antenna or use a more powerful antenna and repeat the scan mode.
Note:

•  In Germany, no DVB-T/T2 radio channels are transmitted.
• After moving to another region you have to repeat the scan mode.

Daily Operation Switching Channels
You can switch between channels using the CH▲/CH▼ keys. Via the numerical keys 0-9 you can go to a specific channel directly.

Channel List
Open the channel list by pressing the OK button.

TV/Radio
For switching from TV to radio channels press the TV/ RADIO key.
Favorite groups
If you have specified any favorite groups, you can access them by pressing the FAV key.

Subtitles
To show subtitles press the SUB-T key.
Highlight the desired subtitle language using the ▲/▼keys. Confirm your selection by pressing OK. In case there are no subtitles available only „off“ will be displayed in the menu.
Close the subtitle menu by pressing the EXIT key.
Select Soundtrack/Language
Some TV channels transmit several soundtracks. Use the AUDIO key to open the soundtrack menu.
Highlight the desired language/audio track using the ▲/▼ keys. Confirm your selection by pressing OK.
Close the soundtrack menu by pressing the EXIT key.
Teletext
The Teletext is activated via the TTX key. Use the numerical keys 0-9 for entering the desired Teletext page.
Volume
Use the ◄/► (VOL+ / VOL-) keys for changing the volume.
In case you are using the HDMI outlet as a bitstream raw interface for surround sound formats, the volume cannot be controlled via the receiver‘s remote control.
ASPECT RATIO
While watching TV you have the option to change the aspect ratio without accessing the menu. Press the ASPECT (YELLOW) key and the aspect ratio will change every time you use the key.
Electronic program guide
Press the EPG key to open the program guide.

Password
The default password is 000000. If you have forgotten your password, use Super-Password 888888.
Program Edit
Open the main menu of the receiver by pressing the MENU key. The sub-menu enables you to move, delete, rename, lock/unlock the channels in the channel list conveniently.
Move

•  Use the ▲/▼ keys to highlight a channel you want to move to a different channel number. Press the RED key to flag the channel for moving it.
•  Use the ▲/▼ to select the new channel number for the flagged channel.
• Confirm the action by pressing OK, the channel will now be moved to the new channel number in the list.

Delete

• Use the ▲/▼ keys to highlight a channel you want
  to delete.

•  Press the BLUE key to flag the channel for deletion.
  A confirmation request appears.

• Confirm the action by pressing OK, the selected channel will now be deleted.

Lock/unlock
The receiver asks for a password before showing a locked channel.

• Use the ▲/▼ keys to highlight a channel you want to lock.
• Press the YELLOW key to flag the channel as locked
• Press the YELLOW key once more to unlock the channel.

Favorite groups
The receiver has 4 favorite groups. You can assign any channel to any group. A channel can be assigned to several groups.

• Use the ▲/▼ keys to select a channel you want to add to a favorite group.
• Open the favorite group’s menu by pressing the FAV key.
• Use the ▲/▼keys to highlight the group you want to assign the channel to.
•  After pressing the OK key a symbol appears in the front of the respective favorite group.

It is possible to select several favorite groups at this point. „Disable“ will clear the assignment to all groups.

You can change the name of the selected group by pressing the RECALL key.

• Press the EXIT key to close favorite groups menu.

Rename channel
Use the ▲/▼ keys to highlight the channel you want to rename and press the RECALL key. An on-screen keyboard will appear. Use the ◄/►/▲/▼keys to highlight the right letters and confirm your selection by pressing the OK key. After completing the name move to the OK field and press the
OK, key. The new name has now been assigned to the channel.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>