KRAMER TP-580CT 4K USB Transmitter User Guide

TP-580CT Quick Start Guide

This guide helps you install and use your TP-580CT for the first time.
Go to www.kramerav.com/downloads/TP-580CT to download the latest user manual and check if firmware upgrades are available.
Scan for full manual

https://de2gu.app.goo.gl/Q24mpJn3V63TuZqo9

Step 1: Check what’s in the box

• TP-580CT 4K USB Transmitter
• 1 Bracket set
• 1 Quick start guide
• 1 Power adapter and cord
• 4 Rubber feet

Step 2: Get to know your TP-580CT

Alternate Mode). Charges sources (that support USB Power Delivery 2.0) up to 60W.
While charging, the charging icon (to the right of the connector) becomes visible and lights orange.
2| IN LED| Lights blue when a USB-C input device is connected.
3| OUT LED| Lights blue when an HDMI output device is detected on the receiver side.
4| LINK LED| Lights green when the HDBT connection is active.
5| ON LED| Lights green when receiving power.
6| HDBT OUT RJ-45 Connector| Connects to the HDBT IN RJ-45 connector on a receiver (for example, TP-580R).
7| RS-232 3-pin Terminal Block Connector| Connects to a PC/serial controller to control the remote-controlled unit (for example, the display on the receiver).
8| IR 3.5mm Mini Jack| Bidirectional IR connection. Outputs a received IR signal (from the HDBT receiver) to
a connected IR emitter or transmits an IR signal (from IR sensor) to the HDBT receiver.
9| SETUP DIP-Switches| Set DIP-switches. By default, DIP switches are set to OFF (up). Changes in DIP-switch settings apply immediately.
DIP #| Description| State
1| IR output modulation| OFF (up) — default| IR pass-through is disabled (38KHz modulation to IR output signal is added).
ON (down)| IR pass-through is enabled.
2| | OFF (up) — default| Normal operation.
ON (down)| FW upgrade via RS-232 is enabled.
10| 20V DC| +20V DC 6A connector for powering the unit and charging the connected input device.

TP-580CT Quick Start

Step 3: Mount TP-580CT

Install TP-580CT using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

•  Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/TP-580CT).

• Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/TP-580CT).

• Ensure that the environment (e.g., maximum ambient temperature & airflow) is compatible with the device.

• Avoid uneven mechanical loading.

• Appropriate consideration of equipment nameplate ratings should be used for avoiding the overloading of the circuits.

• Reliable earthing of rack-mounted equipment should be maintained.

• The maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your TP- 580CT.

Wiring the RJ-45 Connectors

This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors.

For HDBT cables, it is recommended that the cable ground shielding be connected/soldered to the connector shield.

EIA /TIA 568B

PIN| Wire Color
1| Orange / White
2| Orange
3| Green / White
4| Blue
5| Blue / White
6| Green
7| Brown / White
8| Brown

Step 5: Connect the power

Connect the adapter to TP-580CT and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.

www.kramerav.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>