KRAMER KT-1010 / KT-1010RB User Guide
- June 6, 2024
- Kramer
Table of Contents
**KRAMER KT-1010 / KT-1010RB User Guide
**
This guide helps you install and use your KT-1010 / KT-1010RB for the first time.
Go to www.kramerav.com/downloads/KT-1010 or www.kramerav.com/downloads/KT-1010RB to download the latest user manual and check if firmware upgrades are available.
Step 1: Check what’s in the box
- KT-1010 Touch Panel or KT-1010RB Touch Panel (Reduced Bandwidth)
- 12V AC/DC power adapter
- Panel mount bracket
- 1 Quick start guide
- Tabletop mount
- On-wall mount bracket kit
- Installation screws
- 1 Allen key
Step 2: Get to know your KT-1010 / KT-1010RB
Top Slide View
Rear Panel View
Lower Side View
Left Side View
Front View
# | Feature | Function |
---|---|---|
1 | Volume setup button (+/-) | Press to increase/decrease KT-1010 **/KT- |
1010RB** speaker volume.
2| Up/Down (△/▽) Keys| Press to scroll through the menu options.
3| Exit Button| Press to exit the menu.
4| SD Card Slot and Cover| Add an external memory.
5| Power LED| Power on indication. Orange when loading, then turns green.
6| 3 Add-on USB Module Slots| For future use.
7| 2 Speakers| To output the sound.
8| 4 VESA Mounting Screw Holes (75x75mm)| Connect to a VESA kit to mount on
the wall.
9| 12V DC Input with Cable Security Lock| Connect to the AC/DC adapter and to
the mains.
10| Ethernet PoE RJ-45 Connector| Connect to a PC via a LAN.
11| USB Type A Port| Connect to USB peripherals (such as a keyboard, printer,
etc.).
12| Micro USB Port| Connect to USB peripherals (such as a keyboard, printer,
etc.).
13| 2 Control I/O Ports| For future use.
14| Power ON/OFF Switch| Press to turn power on or off.
15| Headphone 3.5mm Mini Jack| Connect to a headphone.
16| Camera| For video conferencing.
17| Microphone| For video conferencing or audio recording.
Step 3: Mount KT-1010 / KT-1010RB
This section describes KT-1010 but applies also to KT-1010RB.
To mount KT-1010 on a wall using the VESA kit:
- Unscrew the 2 security screws and separate the wall mounting brackets. Keep screws and rubber washers for later.
- Secure the on-wall mount to the wall using 2 installation screws and washers (use the built-in level for levelling).
- Attach the panel mount bracket to the VESA mounting holes on the rear side of the KT-1010 (safety screw openings on top).
- Slide the panel mount bracket to the on-wall bracket already mounted on the wall.
- Replace security screws with rubber washers.
To mount KT-1010 on a table:
- Remove the two panel screws on the rear lower-side panel of the tabletop mount.
- Pass the cables through the opening on the rear side.
- Connect the cables to KT-1010.
- Turn the power switch on the rear of the touch panel (14) to ON.
- Place KT-1010 into the tabletop mount.
- Reconnect the lower-side panel using the two panel screws.
Secure KT-1010 from the rear side, via the Tabletop Mount holes, to the VESA
mounting holes on the rear side of the KT-1010.
If required, lock the device using the Kensington lock slot on the right lower
side of the table-mount top.
Warning
- Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
- Avoid uneven mechanical loading.
- Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits.
- Reliable earthing of rack-mounted equipment should be maintained.
- Maximum mounting height for the device is 2 meters.
Step 4: Connect power
Connect the Ethernet port to a PoE Ethernet port, using a PoE-compliant Ethernet cable. Alternatively, or in addition to PoE powering, connect the power adapter to the 12V AC/DC power socket and to the mains electricity.
Safety Instructions
(Seewww.kramerav.com for updated safety
information).
Caution:
- There are no operator serviceable parts inside the unit.
Warning
- Use only the power cord that is supplied with the unit.
- Disconnect the power and unplug the unit from the wall before installing.
Step 5: Operate KT-1010 / KT-1010RB
-
Turn the power switch on the rear of the touch panel to ON.
Wait for Kramer Control log-in page to load.
-
Sign in as follows:
-
If the device is connected to the Internet via cable, click SIGN IN on the panel.
-
If the device is connected to the Internet via Wi-Fi:
-
Press the Exit button (on the KT-1010/KT-1010RB top side) and then
type the password (default: Kramer). -
Click Home Page>Settings>Wi-Fi and choose your SSID Network.
-
Reboot your device.
-
KramerAppUpdate automatically updates Kramer apps.
Tap Home-Page>App Icon>KramerAppUpdate to view installed and available app
versions and to change the Server Check Interval.
3. Operate the Kramer Control App.