KRAMER DSP-62-AEC Digital Sound Processor User Guide

KRAMER DSP-62-AEC Digital Sound Processor User Guide

This guide helps you install and use your DSP-62-AEC for the first time.
Go to www.kramerav.com/downloads/DSP-62-AEC to download the latest user manual and check if firmware upgrades are available.

Check what’s in the box

• DSP-62-AEC Digital Sound Processor
• 1 Power adapter and cord
• 1 Kramer C-USB/AB-6 cable
• 1 Quick start guide
• 4 Rubber feet
• 1 Bracket set

Get to know your DSP-62-AEC

(default) for normal operation (other DIP-switches are reserved for future use).
2| HDMI IN 1 Button| Press to select HDMI IN 1 input (on the front panel).
3| HDMI IN 2 Button| Press to select HDMI IN 2 input (on the rear panel).
4| AUDIO LEDs| USB IN| Lights green when an audio source is received from the USB host port.
USB OUT| Lights green when an audio signal is sent to the USB host port.
5| IN (1 to 5)| Lights green when a signal is present, lights red when clipping is detected. For IN 2 to IN 5, when connecting a microphone and setting to Mic mode via the embedded Web pages, lights blue.
OUT| Lights green when a signal is present, lights red when clipping is detected.
6| AUDIO IN 3.5mm Mini Jack| Connect to an unbalanced audio source.
7| USB Type B Bi-Directional Host Port| Connect to an audio source or acceptor.
8| HDMI IN 1 Connector| Connect to an HDMI source.
9| ON LED| Lights green when the device is powered.
10| HDMI IN 2 Connector| Connect to an HDMI source.
11| HDMI™ OUT Connector| Connect to an HDMI acceptor.
12| AUDIO IN 3-pin Terminal Block Connectors (2 to 5)| Connect to up to 4 mono balanced audio sources (mono or mic level with selectable 48V).
13| AUDIO OUT 5-pin Terminal Block Connector| Connect to a stereo balanced audio acceptor.
14| I/O Terminal Block Connectors (1 to 2)| Connect to up to two sensors, switches, LEDs, or relays.
15| RS-232 (G, Rx, Tx) Terminal Block Connector| Connect to a PC/serial controller
16| ETHERNET RJ-45 Connector| Connect to a PC via a LAN.
17| RESET Recessed Button| Press and hold while powering the device to reset to factory default values, including IP settings.
18| 12V DC Power Connector| Connect to the power supply and to the mains electricity.

Mount DSP-62-AEC

Install DSP-62-AEC using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

• Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/DSP-62-AEC).

• Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/DSP-62-AEC).

• Mount the unit in a Kramer Table-Mount unit
  (see www.kramerav.com/product/DSP-62-AEC).

  • Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
  • Avoid uneven mechanical loading.
  • Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits.
  • Reliable earthing of rack-mounted equipment should be maintained.
  • Maximum mounting height for the device is 2 meters.

Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your DSP-62-AEC.

Connecting the audio output
To a balanced stereo audio acceptor:
To an unbalanced stereo audio acceptor:
To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/DSP-62-AEC. Using third-party cables may cause damage!

Connect power

Connect the power cord to DSP-62-AEC and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:

• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.

Operate the DSP-62-AEC

Operate DSP-62-AEC via:

• Embedded web pages via the Ethernet.
• RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller.

RS-232 Control / Protocol 3000

Baud Rate:| 115,200| Parity:| None
Data Bits:| 8| Command Format:| ASCII
Stop Bits:| 1| |
Example: (adjust analog audio output 1 to “-10dB”): #x-aud-lvl out.analog_audio.1.audio.1,-10
Default Ethernet Parameters
IP Address:| 192.168.1.39| UDP Port #:| 50000
Subnet mask:| 255.255.0.0| TCP Port #:| 5000
Gateway:| 192.168.0.1| User/Password| Admin/Admin
Factory Reset
Recessed Button| Press and hold while powering the device.
Protocol 3000:| “#factory” command.
Web Pages:| In the Settings page, click Reset.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>