USER MANUAL
MODELS: TP-600TRxr
TP-600TR
4K60 HDMI/USB Extender

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

• Unpack the equipment carefully and save the original box and packaging materials for possible future shipment.
• Review the contents of this user manual.
  Go to www.kramerav.com/downloads/TP- 600TRxr or www.kramerav.com/downloads/TP600TR to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).

Achieving Best Performance

• Use only good quality connection cables (we recommend Kramer high-performance, high-resolution cables) to avoid interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality ables).
• Do not secure the cables in tight bundles or roll the slack into tight coils.
• Avoid interference from neighboring electrical appliances that may adversely influence signal quality.
• Position your Kramer TP-600TRxr / TP-600TR away from moisture, excessive sunlight, and dust.

Safety Instructions

Caution:

• This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building.
•  For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located  next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.
• To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which is located on the bottom of the unit.

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfills or incineration by requiring it to be collected and recycled. To comply with the WEEE Directive, Kramer electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of  Kramer’s recycling arrangements in your particular country go to our recycling pages at ww.kramerav.com/il/quality/environment.

**Overview

**

Congratulations on purchasing your Kramer TP-600TRxr/TP-600TR 4K60 HDMI/USB Extender.

TP-600TR is identical to TP-600TRxr except for ETH extension. TP-600TRxr, in this User Manual, refers to both devices unless specified otherwise.  TP- 600TRxr is a high-performance, long-reach HDBaseT 3.0 extender for 4K60Hz (4:4:4) HDMI, USB,  ethernet (TP-600TRxr only), RS-232, and IR signals over twisted pair, flexibly set as transmitter-side or receiver-side device. TP- 00TRxr transmitter-side converts all input signals into the transmitted HDBaseT 3.0 signal.

TP-600TRxr receiver-side receives the HDBaseT 3.0 signal and converts it back into the original input signals. TP-600TRxr extends video signals up to 100m (330ft)  ver CAT copper cables at 4K@60Hz (4:4:4) video resolution.
TP-600TR extends video signals up to 40m (130ft) over CAT copper cables at 4K@60Hz (4:4:4) video resolution and up to 70m  230ft) at 4K@30Hz (4:4:4).
TP-600TRxr provides exceptional quality, advanced and user-friendly operation, and flexible control.

Exceptional Quality

• High-Performance Standard Extender – Professional HDBaseT extender for providing extended-reach signals over twisted-air copper infrastructures. TP-600TRxr is a standard extender that can be connected to any market-available HDBaseT-compliant extension product. For optimum extension reach and performance, use recommended Kramer cables.
• HDMI Signal Extension – HDCP 2.3, EDID, and CEC signals are passed through from the source to the display. Supports  DR10, deep color, x.v.Color™, lip-sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS-HD, 2K, 4K, and 3D  s specified in HDMI 2.0.
• HDMI extension – Uncompressed 4K@60Hz (4:4:4).
• I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID handling, processing, and pass-through algorithm that ensures Plug and Play operation for HDMI source and display systems.

Advanced and User-friendly Operation

• HDMI Mirroring – Transmitter-side extender mirrors input HDMI signal to the loop output port for connecting a local monitor r an additional unit in a daisy chain.
•  Flexible USB 2.0 Extension – An active USB host is connected to the extender at either the transmitter or receiver sides.  SB 2.0 signals are extended between the extender transmitter and receiver sides, enabling connection of the active USB host o both local and remote USB devices, such as camera and audio devices, or HID (Human Interface Devices) mouse or keyboard devices.
• Cost-effective Maintenance – Status LED indicators for HDMI, Loop, HDBT, and USB active host ports, facilitate easy ocal maintenance and troubleshooting.
• Easy and Elegant Installation – MegaTOOLS™ fan-less enclosure for dropped-ceiling mounting, or side-by-side mounting f 2 units in a 1U rack space with the recommended rack adapter.

Flexible Connectivity

• Multi-channel Audio Transmission – Up to 32 channels of digital stereo uncompressed signals for supporting studio-grade surround sound.
•  Flexible USB 2.0 host and devices extension. Ethernet Extension (TP-600TRxr only)
• Ethernet interface data flows in both directions, allowing extension of up to 1 Gbps Ethernet connectivity for LAN  ommunication and device control.
•  Bidirectional RS-232 Extension – Serial interface data flows in both directions, allowing data transmission and device control.
•  Bidirectional Infrared Extension – IR interface data flows in both directions, allowing remote control of peripheral devices located at either end of the extended line.

Typical Applications
TP-600TRxr is ideal for the following typical applications:

• Corporate – Hybrid and online meetings.
• Education – Hybrid and online learning and training.
• Any AV, Ethernet (TP-600TRxr only), and USB room extension applications such as conference rooms, boardrooms, and training facilities.

Defining TP-600TRxr 4K60 HDMI/USB Extender

This section defines TP-600TRxr and TP-600TR.
The extender device functions as a transmitter or receiver as defined by the SETUP DIP-switch 1 setting on the rear panel (see etting the DIP-Switches on page 11).

Connect to the USB peripheral devices (for on either the transmitter the 4K60 HDMI/USBhost (for example, a laptop) to communicate with the USB example, a smart board) connected to USB device ports or the receiver sides of the extender (see Connecting Extender on page 7).

2| ACTIVE HOST LED| Lights orange when the USB host side is active
3| ACTIVE Rx LED| Lights green when the extender receiver function is active
4| IN LED| Lights blue when an active HDMI input signal is detected on HDMI IN.
5| OUT LED| Lights blue when an output acceptor device is connected.
6| TX LOOP| Transmitter mode| Lights blue an active signal is transmitted on the Tx LOOP port.
Receiver mode| N/A
7| LINK LED| Lights green when the HDBT active link connection is established.
8| ON LED| Lights green when the device receives power.

| Feature| Function

---|---|---
9| ENTER Button| Press to move to the next level in the OSD screen or to accept a new parameter.
10| HDMI TX IN Connector| Transmitter mode| Connect to an HDMI source.
Receiver Mode| N/A
11| HDMI Rx
OUT/Tx LOOP Connector| Transmitter mode| Connect to a local acceptor.
Receiver mode| Connect to an HDMI acceptor.
12| USB A 2.0 Fast- Charging Connectors (3)| Connect to the USB local peripheral devices (for example, a USB camera, a soundbar, microphone and so on).
13| IR 3.5mm Mini Jack Connector| Connect to an external IR emitter to control a local IR-controlled device from the remote extender (for example, TP- 600TRxr).
Connect to an IR sensor to control a remote IR-controlled device connected to the remote extender side (for example, TP-600TRxr).
14| RS-232 3-pin Terminal Block| Connect to a controller device (for example, SL240C) to control a remote device via serial connection (for example, the remotely connected PTZ USB camera).
15| ETHERNET RJ-45 Connector| Connect to LAN.
16| SETUP 4-way DIP-switch| Sets the device behavior (see Setting the DIP- Switches on page 11).
17| 12V DC Power Connector| Connect to the power supply.

Mounting TP-600TRxr

This section provides instructions for mounting TP-600TRxr. Before installing, verify that theenvironment is within the recommended range:

• Operation temperature – 0° to 40°C (32 to 104°F).
• Storage temperature – -40° to +70°C (-40 to +158°F).
• Humidity – 10% to 90%, RHL non-condensing.

Caution:

•  Mount TP-600TRxr before connecting any cables or power.

Warning:

• Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be used for avoidingoverloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.

Mount TP-600TRxr in a rack:

• Use the recommended rack adapter (see www.kramerav.com/product/TP-600TRxr).
  Mount TP-600TRxr on a surface using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

• Fasten a bracket (included) on each side of the unit and attach it a flat surface. For more information go to www.kramerav.com/downloads/TP-600TRxr.

Connecting the 4K60 HDMI/USB Extender

You can use two TP-600TRxr units, define them as transmitter and receiver and then connect the transmitter to the receiver (as described in this section). You can also connect the device to a different unit. For example:

• Connecting TP-600TRxr that is set as a transmitter to the Kramer TP-590R receiver.
• Connecting a transmitter (for example, the Kramer TP-590T transmitter) to a TP-600TRxr that is set as a receiver.
•  Connecting the TP-600TRxr (defined as a transmitter or receiver to a switcher or other system, for example, the VS-84UT).

This section describes the following actions:

• Connecting TP-600TRxr on page 7.
• Connecting TP-600TR on page 9.
•  Connecting to TP-600TRxr via RS-232 on page 11.
•  Error! Reference source not found. on page Error! Bookmark not defined..
•  Setting the DIP-Switches on page 11.

Always switch off the power to each device before connecting it to your TP- 600TRxr. After connecting your TP-600TRxr,  connect its power and then switch on the power to each device.

Connecting TP-600TRxr

To connect TP-600TRxr as illustrated in the example in Figure 5:

1. Use the DIP switches to define one device as a transmitter and the other as a 14 receiver (see Setting the DIP-Switches on page 11).

2.  Connect the HDBT port on the TP-600TRxr transmitter side to the HDBT port 9 on 9 the TP-600TRxr receiver side.

3. On the TP-600TRxr transmitter side, connect an HDMI source (for example, a laptop) to the HDMI Tx IN connector10.

4. On the TP-600TRxr transmitter side, connect the HDMI Rx OUT/Tx LOOP connector  11 to an HDMI acceptor.

5.  On the TP-600TRxr receiver side, connect the HDMI Rx OUT/Tx LOOP connector to 11 an HDMI acceptor (for example, a smart TV).

6. Connect the USB ports:
   ▪ Connect the HOST USB port to a laptop or room PC.
   The HOST USB port can be connected to either the transmitter or the receiver side, as necessary.
   ▪ Connect the USB DEVICE ports on the transmitter side to USB devices (for example, the room microphone, mouse, and keyboard).
   ▪ Connect the USB DEVICE ports on the receiver side to USB devices (for example, a smartboard, soundbar, and camera).
   USB devices can be connected to both the transmitter and receiver sides, as necessary.

7. To control the smart TV via IR, connect the following:
   ▪ On the TP-600TRxr transmitter side, connect an IR sensor cable to the IR 3.5mmmini jack 13.
   ▪ On the TP-600TRxr receiver side, connect the IR 3.5mm mini jack13 to an emitter cable and attach the emitter side to the IR sensor of the smart TV.
   Point the smart TV IR remote controller to the IR sensor to pass an IR command via HDBT to the smart TV.

8. To Control the smart TV via Ethernet, connect the following:
   ▪ On the TP-600TRxr transmitter side, connect a room controller (for example, the Kramer SL-240C with Kramer Control) to the Ethernet RJ-45 port15.
   ▪ On the TP-600TRxr receiver side, connect the Ethernet RJ-45 port15 to the smart TV.
   Send IP commands via the room controller to the smart TV via LAN.

9. To control the PTZ camera, connect the following:
   ▪ On the TP-600TRxr transmitter side connect a controller (for example, SL- 240C room controller) to the RS-232 port14 (and also to the ETHERNET RJ-45 port15.
   ▪ On the TP-600TRxr receiver side connect the RS-232 port14 to a PTZ camera.
   Send serial commands from SL-240C to the camera via RS-232.

10.  Connect the power adapter to TP-600TRxr and to the mains electricity (not shown in Figure 5).
    TP-600TRxr is connected.

Connecting TP-600TR

To connect TP-600TR as illustrated in the example in Figure 5:

1. Use the DIP-switches 14 to define one device as a transmitter and the other as a 14 receiver (see Setting the DIP-Switches on page 11).

2. Connect the HDBT port on the TP-600TR transmitter side to the HDBT port 9 on the TP-600TR receiver side.

3.  On the TP-600TR transmitter side, connect an HDMI source (for example, a laptop) to the HDMI Tx IN connector.

4. On the TP-600TR transmitter side, connect the HDMI Rx OUT/Tx LOOP connector 11 to an HDMI acceptor.

5. On the TP-600TR receiver side, connect the HDMI Rx OUT/Tx LOOP connector to 11 an HDMI acceptor (for example, a smart TV).

6. Connect the USB ports:
   ▪ Connect the HOST USB port to a laptop or room PC.
   The HOST USB port can be connected to either the transmitter or the receiver side, as necessary.
   ▪ Connect the USB DEVICE ports on the transmitter side to USB devices (for example, the room microphone, mouse, and keyboard).
   ▪ Connect the USB DEVICE ports on the receiver side to USB devices (for example, a smartboard, soundbar, and camera).
   USB devices can be connected to both the transmitter and receiver sides, as necessary.

7. To control the smart TV via IR, connect the following:
   ▪ On the TP-600TR transmitter side, connect an IR sensor cable to the IR 3.5mm mini-jack13.
   ▪ On the TP-600TR receiver side, connect the IR 3.5mm mini-jack to an emitter cable and attach the emitter side to the IR sensor of the smart TV.
   Point the smart TV IR remote controller to the IR sensor to pass an IR command via HDBT to the smart TV.

8. To control the PTZ camera, connect the following:
   ▪ On the TP-600TR transmitter side connect a controller (for example, SL-240C room controller) to the RS-232 port (and also to the ETHERNET RJ-45 port 15).
   ▪ On the TP-600TR receiver side connect the RS-232 port 14 to a PTZ camera.
   Send serial commands from SL-240C to the camera via RS-232.

9. Connect the power adapter to TP-600TR and to the mains electricity (not shown in Figure 5).
   TP-600TR is connected.

Connecting to TP-600TRxr via RS-232

You can connect to TP-600TRxr via an RS-232 connection13 using, for example, a PC.
TP-600TRxr features an RS-232 3-pin terminal block connector to extend RS-232 signals viaTP-600TRxr transmitter and  receiver.
Connect the RS-232 terminal block on the rear panel of TP-600TRxr to a device, as follows:
From the RS-232 9-pin D-sub serial port connect:

• Pin 2 to the TX pin on the TP-600TRxr RS-232 terminal block
• Pin 3 to the RX pin on the TP-600TRxr RS-232 terminal block
• Pin 5 to the G pin on the TP-600TRxr RS-232 terminal block
  RS-232 Device TP-600TRxr
  

EIA /TIA 568B

PIN| Wire Color
1| Orange / White
2| Orange
3| Green / White
4| Blue
5| Blue / White
6| Green
7| Brown / White
8| Brown

Setting the DIP-Switches

All changes in DIP-Switches apply immediately, on the fly (no need to power cycle the device), except for DIP-switches 1 and 2.
All DIP switches are set to OFF (up) by default.

SETUP

ON (down) – Transmitter mode is active.
2| Active USB Host port| OFF (up) – Host is active.
ON (down) – Host is inactive (active on remote paired device).
3| Define IR Pass-through| OFF (up) – Pass through the IR signal to or from the IR cable.
ON (down) – Add IR modulation (38kHz) to the IR output signal (applies only when the IR port is connected to an IR emitter cable).
4| Programing RS-232| Off (up) – Normal operation mode is enabled (FW programming RS-232 is inactive).
On (down) – FW programming RS-232 is active.

Technical Specifications

TP-600TRxr Specifications

Receiver Side
1 I-IDBT| On a female RJ-45 connector
Outputs| Transmitter Side
1 I-IDBT| On a female RJ-45 connector
1 LOOP| On a female HDMI connector
Receiver Side
1 HDMI| On a female HDMI connector
Ports| 1 USB 2.0 Host| On a USB-B female connector
3 USB 2.0 Device| On USB type-A female connectors
1 1000BaseT Ethernet| On an RJ-45 female connector for LAN extension
1 IR| On a 3.5mm mini-jack for IR link extension
1 RS-232| On a 3-pin terminal block for serial link extension
Extension Line| Reach| Up to 100m (330ft), when using Kramer HDBaseT cables
Standards Compliance| HDBaseT 3.0
Video| Max Data Rate| 18Gbps bandwidth (6Gbps per graphic channel)
Max Resolution| 4K©60Hz (4:4:4) 24bpp resolution
Content Protection| HDCP 2.3
HDMI Support| 4K as specified in HDMI 2.0b
Extended USB| Data Rate| Up to 480Mbps
Transmitted Data Bandwidth| Up to 300Mbps
Standards Compliance| 1.1 and 2.0 USB
Extended Ethernet| Max Data Rate| 1Gbps
Extended RS-232| Baud Rate| 300 to 115200
Power| Consumption| 12V DC, 3200mA
Source| 12V DC, 5A
Environmental Conditions| Operating Temperature| 0° to +40’C (32° to 1047)
Storage Temperature| -40° to +70°C (-40′ to 1587)
Humidity| 10% to 90%, RHL non-condensing
Regulatory Compliance| Safety| CE
Environmental| RoHs, WEEE
Enclosure| Size| Mega Tool
Material| Aluminum
Cooling| Convection Ventilation
General| Net Dimensions (W, D, H)| 19cm x 11.6an x 2.7cm (7.5′ x 4.6′ x 1.11
Shipping Dimensions (W, D, H)| 34.5cm x 16.5cm x 5.2cm (13.6′ x 6.5′ x 2′)
Net Weight| 0.56kg (1.2Ibs)
Shipping Weight| 1.15kg (2.5Ibs) approx.
Accessories| Included| Power adapter and cord
Specifications are subject to change without notice at www.krameray.com
Inputs| Transmitter Side
---|---
11-IDMI I On a female HDMI connector
Receiver Side
1 HDBT On a female RJ-45 connector
Outputs| Transmitter Side
11-IDBT| On a female RJ-45 connector
1 LOOP| On a female HDMI connector
Receiver Side
1 HDMI| On a female HDMI connector
Ports| 1 USB 2.0 Host| On a USB-B female connector
3 USB 2.0 Device| On USB type-A female connectors
1 IR| On a 3.5mm mini-jack for IR link extension
1 RS-232| On a 3-pin terminal block for serial link extension
Extension Line| Reach| Up to 40m (1308) at 4)0260Hz (4:4:4), when using Kramer I-TD based cables
Up to 70m (2308) at up to 4K@3OHz (4:4:4), when using Kramer I-IDBaseT cables
Standards Compliance| HDBaseT 3.0
Video| Max Data Rate| 18Gbps bandwidth (6Gbps per graphic channel)
Max Resolution| 4K©60Hz (4:4:4) 24bpp resolution
Content Protection| HDCP 2.3
HDMI Support| 4K as specified in HDMI 2.0b
Extended USB| Data Rate| Up to 480Mbps
Transmitted Data Bandwidth| Up to 300Mbps
Standards Compliance| 1.1 and 2.0 USB
Extended Ethernet| Max Data Rate| 1Gbps
Extended RS-232| Baud Rate| 300 to 115200
Power| Consumption| 12V DC. 600mA
Source| 12V DC. 2A
Environmental Conditions| Operating Temperature| 0° to +40°C (32′ to 1047)
Storage Temperature| -40° to +70’C (-40′ to 1587)
Humidity| 10% to 90%, RHL non-condensing
Regulatory Compliance| Safety| CE
Environmental| RoHs, WEEE
Enclosure| Size| Mega Tool
Material| Aluminum
Cooling| Convection Ventilation
General| Net Dimensions (W, D, H)| 19cm x 11.6cm x 2.7cm (7.5″ x 4.6′ x 1.11
Shipping Dimensions (W, D, H)| 34.5cm x 16.5cm x 52crn (13.6′ x 6.5″ x 2′)
Net Weight| 0.55kg (1.2lbs)
Shipping Weight| 1.12kg (2.5Ibs) approx.
Accessories| Included| Power adapter and cord
Specifications are subject to change without notice at www.kramerav.com

The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:
What is Covered
This limited warranty covers defects in materials and workmanship in this product.
What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product. Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used.
How Long this Coverage Lasts

The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:

1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year warranty for firmware and software updates; all Kramer VIA accessories, adapters, tags, and dongles are covered by a standard one (1) year warranty.

2. Kramer fiber optic cables, adapter-size fiber optic extenders, pluggable optical modules, active cables, cable retractors, ring-mounted adapters, portable power chargers, Kramer speakers, and Kramer touch panels are covered by a standard one (1) year warranty. Kramer
   7-inch touch panels purchased on or after April 1st, 2020 are covered by a standard two (2) year warranty.

3. All Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all streaming, and all wireless products are covered by a standard three (3) year warranty.

4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.

5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for three (3) years).

6. K-Touch software is covered by a standard one (1) year warranty for software updates.

7. All Kramer passive cables are covered by a lifetime warranty.

Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or owners of this product.
What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty:

1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product. If a direct or similar replacement product is supplied, the original product’s end warranty date remains unchanged and is transferred to the replacement product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty.

What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re-installation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any adjustment of  user controls or any programming required for a specific installation of this product.
How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service providers, visit our website at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be required (RMA number).
You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original carton, for shipping. Cartons not bearing a return authorization number will be refused.
Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR  UNDER ANY OTHER LEGAL THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.
Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES, AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,  WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW. IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY ACT (15 U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU, AND ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF  MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE, SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.
Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state. This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an authorized Kramer Electronics reseller, visit our website at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this document. Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of satisfaction.

SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our website where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All brand names, product names, and trademarks are the property of their respective owners.
www.KramerAV.com
info@KramerAV.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>