Laney AH-Freestyle AudioHub Acoustic Guitar Combo Amplifier User Manual

Laney AH-Freestyle AudioHub User Manual

IMPORTANT SAFETY INSTRUCTIONS

1. Read & Retain these Instructions carefully before installing or operating this product.

2. Comply with Warnings: All warnings and instructions for these products should be adhered to.

3. Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the Laney factory to your dealer. In the unlikely event that there has been damage, please repack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification securely packed.

4. Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on source equipment, CD/MP3 players, mixers/recorders, etc, BEFORE turning on your guitar amplifier.Many products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your guitar amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loud speakers.Wait till all system parts have stabilised, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your guitar amplifier and then turn off its power before turning off other equipment

5. Servicing: Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the DC Power Supply is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

6. Placement: This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids, such as vases, upon the apparatus.
   Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not block any of the ventilation openings.
   Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

7. When using the DC power Supply: Only use the approved DC power supply provided by the manufacturer. Rating 12Vdc 500mA. Protected by a 125°C thermal fuse.
   Make sure that the line voltage at the installation matches the input voltage on the DC power Supply.
   Protect the power cord on the DC power Supply from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus. (See notes on using the DC Power Supply page 6).

8. Batteries: Use only alkaline batteries (LR6) in the product. (See notes on fitting and replacing batteries page 6-7).

9. Sound Levels: Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
   The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.

10. Maintenance: Clean only with a dry cloth.
    Care of your Laney amplifier will prolong it’s life…..and yours!

WELCOME

Dear Player,

Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family.

Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment.

Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parents’ garage.

Since then we have moved on from strength to strength developing an extensive range of guitar, bass, public address, multi instrument and keyboard amplification products along with a list of Laney endorses that includes some of the world’s most famous and respected musicians.

At the same time we believe we have not lost sight of the reason Laney was founded in the first place – a dedication to building great sounding amplification for working musicians.

Warm Regards,

Lyndon Laney
Chairman and Founder.

INTRODUCTION

The Audiohub range of multi instrument amplifiers is designed to be the centre of your audio world.

The portable AH-FREESTYLE, great for bedroom, practice or busking, features 3 independent channels allowing connection of balanced XL, line and Hi- Impedance/Instruments, as well as a dedicated Aux In.

The AH-FREESTYLE can be run from a wall mounted mains adaptor, or from batteries in the rear compartment. It is equipped with a delay unit with Time and Feedback controls, and an FX send switch on each channel.

Ideal for keyboards, vocals, electronic drums and playing recorded audio, the Audiohub series features custom drivers to ensure that whatever sound source you use is produced and projected correctly and clearly. Add to this ‘Road Ruggedness, solid construction, hard waring vinyl and a metal front Grille.

The AH-FREESTYLE is the ideal solution for all of your audio performance and rehearsal needs…..wherever you are!

QUICK START SECTION: – Powering up

DC Power Supply: Your AH-Freestyle comes supplied with a 12V DC Power Supply, this is easily fitted between the mains outlet and the amp. When using the amp with the power supply a few precautions should be followed:

1. Only use the DC Power supply that is supplied by the manufacturer. The use of other DC Power Supplies may cause  damage or other problems.
2. Turn the power switch to OFF and disconnect any other attached devices, before plugging in and turning ON the DC Power Supply.
3. When the DC Plug is connected to the socket, the battery compartment is isolated from the unit. Both the DC Power Supply and the battery tray are independent of each other.
4. Although no harm will come to the batteries if left in place whilst the DC Power supply is being used, it is recommended that they be removed. Use either one power source or the other.

Batteries: The use of a DC Power Supply is recommended as the units main power source, however, should you prefer to use batteries, use only Alkaline type (LR6).
Used continuously the batteries will last for approximately 40 hours. (This will vary greatly with the actual conditions of use).

As the batteries run down, the power indicator on the fascia panel will become dim when the battery power is too low. Replace the batteries or revert to the DC Power Supply.

Fitting Batteries: When installing or replacing batteries, always turn the power switch to the OFF position and disconnect any other devices you have may have connected. This prevents damage to your speaker and/or other devices. Follow the photo sequence to fit a set of batteries.

1. Turn the amplifier around to access the battery tray that is located on the back the chassis, place the amp on a piece of felt or cloth to avoid damage.
2. Push the catch to release, then lift out the lid of the battery tray and insert 6 AA batteries, ensure that the orientation is correct to the legend on the tray.
3. When closing the lid of the battery tray, insert the tabs opposite the catch first, then push the lid down until a click is heard.

If used incorrectly batteries may leak or explode and cause damage or injury, please take the following precautions.

1. Carefully follow the installation instructions for fitting new batteries, especially the polarity.
2. Avoid mixing new batteries with old or part used batteries.
3. Avoid mixing battery types.
4. Do not try to recharge or take apart alkaline batteries.
5. Remove the batteries from the unit if it is not going to be used for a long time.
6. If batteries have leaked in the battery tray, remove the batteries and all traces of the discharge from the tray. Use caution so that none of the  discharge gets near the skin or the eyes. Any affected areas should be immediately rinsed with cold running water seek medical advice,
7. Do not dispose of used batteries in fire or water systems. Batteries must not be exposed to excessive heat such as sunlight, fire or the like.
8. Used batteries should always be disposed of in compliance with the current regulations applicable to the country/region where you live.

Attaching the Strap: Attach the supplied strap to the buttons on each side of the cabinet securely, so that it does not become detached causing damage or injury.

FRONT & REAR PANEL CONTROLS

1. CH1 MIC/LINE INPUT: Combi Socket providing either a Balanced XLR input for low impedance microphone signals (200-600 Ohms), or an Unbalanced Jack input socket for connection of all line level signals (keyboard, signal processor, sample, drum machine, etc.).

2. CH1 LEVEL: Adjusts the channel level, enabling the user to balance levels across channels.

3. FX SEND: When pushed in, this switch routes the channel signal to the built in digital delay.

4. CH2 STEREO LINE INPUT: 2 x Unbalanced Jack sockets for connection of a stereo line signal. Sockets may also be used to connect a single mono source, or two individual sources.When connecting independent sources, use the output controls on your device to adjust the balance between the two signals.Active instruments may also be connected here.

5. & 6. CH2 LEVEL & FX: See CH 1 LEVEL & FX.

7. CH3 LINE/INSTRUMENT INPUT: Unbalanced high impedance input for connection of high impedance devices such as electric guitars/basses, or regular line devices.This channel features +6dB gain compared to the other line inputs, so take care if connecting a line level device here.

8. & 9. CH3 LEVEL & FX: See CH1 LEVEL & FX.As this channel has more gain than the other line inputs, don’t be surprised if you find that you need to set this control lower than the others when using line level devices.

10. DELAY TIME Controls the amount of time between repeats of the inbuilt delay.Turning this control clockwise will increase the delay time.

11. DELAY FEEDBACK This controls the amount of repeats in the inbuilt delay.Turning the control clockwise increases the amount of repeats.

SAMPLE SETUP

SPECIFICATIONS

SAFETY INFORMATION

In order to take full advantage of your new product and enjoy long and trouble-free performance, please read this owner’s manual carefully, and keep it in a safe place for future reference.

1. Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the Laney factory to your dealer. In the unlikely event that there has been damage, please re-pack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification securely packed.
2. Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc, BEFORE turning on your amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your bass amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loud speakers. Wait till all system parts have stabilised, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your bass amplifier and then turn off its power before turning off other equipment
3. Cables: Never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete system.
4. Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.

FCC COMPLIANCY STATEMENT

This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, that may cause undesired operation.

Warning: Changes or modification to the equipment not approved by Laney can void the user’s authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This product conforms to the requirements of the following European Regulations, Directives & Rules:
CE Mark (93/68/EEC), Low Voltage (2014/35/EU), EMC (2014/30/EU),
RoHS (2011/65/EU). ErP (2009/1 25/EU).

In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in our country.

WARNING: When using electrical products, basic cautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions safe.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

9. An apparatus with Class I construction shall be connected to a mains socket outlet with a protective connection. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.A grounding type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.

11. Only use attachments/accessories provided by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. The mains plug or appliance coupler is used as the disconnect device and shall remain readily operable. The user should allow easy access to any mains plug, mains coupler and mains switch used in conjunction with this unit thus making it readily operable. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.

16. If this product is to be mounted in an equipment rack, rear support should be provided.

17. Note for UK only: If the colours of the wires in the mains lead of this unit do not correspond with the terminals in your plug, proceed as follows:
    a) The wire that is coloured green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, coloured green or
    colored green and yellow.
    b) The wire that is coloured blue must be connected to the terminal that is marked with the letter N or the colour black.
    c) The wire that is coloured brown must be connected to the terminal that is marked with the letter L or the colour red.

18. This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids, such as vases, upon the apparatus.

19. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
    The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.

20. Symbols & nomenclature used on the product and in the product manuals, intended to alert the operator to areas where extra caution may be necessary, are as follows:
    Intended to alert the user to the presence of high ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical shock to persons.

Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.

Risk of electrical shock – DO NOT OPEN. To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified personnel.

To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this appliance please read the operating instructions.

If your appliance features a tilting mechanism or a kickback style cabinet, please use this design feature with caution. Due to the ease with which the amplifier can be moved between straight and tilted back positions, only use the amplifier on a level, stable surface. DO NOT operate the amplifier on a desk, table, shelf or otherwise unsuitable non-stable platform.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>