LANEY-F67 Active Loudspeaker User Manual

LANEY SOUND SYSTEMS

USER MANUAL

www.laney.co.uk

FEATURES

1. – PAIR BUTTON
2. – PAIR LED
3. – VOLUME CONTROL
4. – BASS
5. – TREBLE
6. – AUX IN
7. – USB CHARGING SOCKET
8. – POWER LED
9. – POWER SWITCH
10. – PSU SOCKET

OPERATION

POWERING ON

• Turn volume (3) down.
• Throw the power switch (9).
• Press the PAIR (1) button — follow the instructions detailed below.
• Connect to LANEY SOUND SYSTEMS-BT PLAYER on your device.
• Play Music.

PAIRING

• If the blue pair led is not illuminated then no device is connected to the LANEY SOUND SYSTEMS-BT PLAYER.
• In order to pair your device, follow the procedure detailed below.
• Press the pair button (1) for 1 second to activate pairing mode.
• The blue led will flash slowly. Pairing mode times out after one minute.
• 0n your device search for LSS-BT PLAYER and connect. The led will change to continuous blue when connected.
• Note, you cannot start a new pairing request whilst a device is already connected, you must first disconnect the first device and then start pairing.
• The LANEY SOUND SYSTEMS-BT PLAYER allows multiple devices to connect to it. If you have previously connected, it should accept a connection request.
• If you start playing a song, it will take over from the currently connected device. The pair led will change to an intermittent blue flash when multiple devices are connected.
• Pressing and holding the pair button for 10 seconds forces the LANEY SOUND SYSTEMS-BT PLAYER to forget all the devices currently connected.

PLAYING TRACKS

• When your device is connected. You can quickly tap the PAIR (1) button to play/pause the currently selected track. The led will briefly blink red/blue

• When there is a track playing. you can double-tap the pair button to skip to the next track.
  AUX IN (6)

• Use the provided 1/8″ aux cable to connect your device to your AUX-IN input.
  CHARGING YOUR DEVICE (7)

• You can use your LANEY SOUND SYSTEM-BT player straight out of the box. but it is recommended that you give it a full 8 hours charge before you use it the first time in order to get optimum battery life.

• You can also use the LANEY SOUND SYSTEMS-BT PLAYER as a powerbank to charge your device using the USB port.
  CHARGING YOUR BLUETOOTH SPEAKER

• Defaults to blue when powered on. The led will start flashing as the battery runs low to indicate it should be charged soon. The led flashes progressively slower as the battery is nearing exhaustion. The led changes to red when it is being charged from the external 12V PSU.

• Connect the supplied PSU to the charging socket (10) on the rear of the unit.

SPECIFICATIONS

Model|

F67-LIONHEART/F61-SUPERGROUP

---|---
Frequency response (-3)| 50Hz-20KHz
Sensitivity (1W/1M)| 88 dB
Max SPL (1M) (Peak)| 105 dB
Power Rating| 160W Peak 80W Continuous 40W RMS
Nominal System Impedance| 4Ω
Input Connector| Stereo 3.5mm Aux-In
Cabient Type| Bass Reflex, Dual front porting
Other| Bluetooth 4.1 A2DP
Controls| Bass, Treble, Volume. Pair Button, On/Off toggle switch.
HF Driver| 2x 3/4″ Dome Tweeter
LF Driver| 4″ dual-coil woofer
Enclosure| Wooden
Finish| 167- LIONHEART – Durable Blue vinyl finish with Lionheart Cream/Blue Front Fret F61-SUPERGROUP – Durable Black vinyl with Supergroup vintage front fret Integrated carry strap handle
Handle
Power supply| Comes with 12V/3A SMPS. Charges internal battery. PSU is -100-240V universal with separate mains lead
Unit dimensions (HWD)| 16 x 26.5 x 15.5 cm /6.3″ x 10.4″x 6.1″
Unit weight| 2.8Kg, 6.2 lbs
Carton dimensions (HWD)| 28 x 31.5 x 21.5 cm/11″ x 12.4″ x 8.5″. 0.019 M3
Packed weight| 3.5Kg, 7.7 lbs

SAFETY INFORMATION

GENERAL INSTRUCTIONS

In order to take full advantage of your new product and enjoy the long and trouble-free performance, please read this owner’s manual carefully, and keep it in a safe place for future reference.

1. Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the Laney factory to your dealer. In the unlikely event that there has been damage, please re-pack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to your dealer for rectification securely packed.
2. Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors, etc, BEFORE turning on your amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your bass amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loudspeakers. Wait till all system parts have stabilized, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your bass amplifier and then turn off its power before turning off other equipment
3. Cables: Never use a shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete system.
4. Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, that may cause undesired operation.
   Warning: Changes or modifications to the equipment not approved by Laney can void the user’s authority to use the equipment.

Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help

This product conforms to the requirements of the following European Regulations, Directives & Rules: CE Mark (93/68/EEC), LowVoltage 2014/35/EU, EMC (2014/30/EU), RoHS (201 I/65/EU), RED (2014/30/EU), ErP 2009/125/EU
SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Laney Electronics Ltd. declares that the radio equipment is in compliance with Directives 2014/53/EU, 201 I/65/EU, 2009/ I 25/EU Full text of the EU declaration of conformity is available at the following internet address: support.laney.co.uk/approvals
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste at landfill sites. It must be taken to an approved recycling center according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Headstock Distribution Ltd is under license. Other trademarks and trade names are those of their respective owners. Laney is a registered trademark of Headstock Distribution Ltd.

INCORPORATED RADIO EQUIPMENT DEVICE TECHNICAL SPECIFICATION:
Frequency Range: 2402-2480MHz
Transmit Power: +8dBm (6.3mW)
Receiver Sensitivity: -9I dBm

F67-LIONHEART
F67-SUPERGROUP
Manufacturer: Laney Electronics Ltd.
© 2018 Laney Electronics Ltd. May not be reproduced without prior written consent
In the interest of continued product development, Laney reserve the right to amend product specification without prior notice
www.laney.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>