JOH01 Wi-Fi Trail Camera User Manual

JOH0 1 Wi-Fi Trail Camera
USER MANUAL

Introduction

Features

•  3, 5, 8, 12, 14, 16, 20, 24 or 30 Mega-pixel high-quality resolution
• 480P, 1080P, 2K or 4K Video resolution
•  Wi-Fi connection and APP remote control
•  42Pcs 850nm Infrared LEDs
• Night flash range as far as 75 feet
•  2.4-inch color screen
• Pre-detection PIR sensor
• 0.2s fast trigger speed motion sensor
• Motion Detection and Time Lapse mode
• Multi-shot, max up to 10 shot
• 120° detection angle
•  Password protection
•  I P66 waterproof
• Timer setting
•  Date, timestamp, and moon phrase

Application

• Wildlife Scouting Hunting
•  Nature Watching Photograph
•  Surveillance & Security

Overview

Installation

Power Supply
Require 4x or Bx 1.5V AA Alkaline Batteries.
Recommend to use 8x AA Alkaline Batteries for best performance.

Note:
1. Not recommended using rechargeable batteries as the lower voltage may cause issues.
2. Do not mix battery type.
3. Install or remove batteries when the camera is in OFF mode.

Inserting SD Card

Required a Micro SD memory card, max capacity 512GB, Class 10 or above Recommend using SanDisk 32GB SDHC/Class 10 memory card to the
best performance.
Note : Format the SD card before using it.

Basic Operation

Switch Mode
OFF Mode
The OFF mode is the safe mode when any action needs to be taken (e.g Install or remove SD card, batteries). And the camera can be switched to off mode if the camera is not used for a short time, please remove the battery if it is not applicable for a long time.
SETUP Mode
The SETUP mode is for you to program the camera, you can check and change the settings of the camera by using the built-in LCD screen, e.g photo or video resolution, the interval between photos, etc.
ON Mode
The camera will work following your programming when in ON mode, which means entering a surveillance mode if you set it as ‘Motion Detection. The camera will automatically take photos or video when the PIR sensor is triggered by activity. If you set it as a ‘Time Lapse’, the camera will be ready to work following your time setting, PIR motion sensor will not work.

Note:
When the camera is in ON mode, the camera will enter the surveillance mode and the camera’s buttons will not work, if you want to reprogram your camera, just switch to the SETUP position again to wake it up.

Switch Mode

Motion Detection
The motion detection mode will enable the camera’s PIR sensor to work, detect signs of surrounding activities within a certain range, and take photos according to your programming, record videos or take photos and record videos at the same time if you want to adjust the PIR sensor parameters, Please refer to the following setting options.

PIR Interval| 5s-60m; Default 30s| PIR sensor will not work at this period, no photos and no videos
---|---|---
PIR Sensitivity| Low/Medium/High;
Default Medium| Temperature affects sensitivity. The High setting is suitable when the ambient temperature is warm; you want to capture distant objects or capture more, and the Medium/Low setting is helpful in cold weather. Note: This option is invalid if enable Time Lapse
IR LED| Auto/Economy/Off;
Default Auto| Auto option will work in the best performance. The Economy option will aim at saving power to extend the battery life. The Off option will turn off the IR LED light, and the effect of taking pictures at night is very poor.
Side PIR Setup| Off/On; Default On| The two side PR sensors provide wider sensing angle and enhance response time, However, in some situations, you might have difficulties removing the interfering thighs, or avoiding the sunlight. If so, have an option to turn off the side sensors
| | On option for you only want the camera to work at a specified period every day. For instance, if the starting time is set at 18:35 and the ending
---|---|---
Monitoring Period| Off/On; Default Off| time at 8:25, the camera will function from 18:35 the current day to 8:25 the next day. rest of the period the camera will not be triggered or take photos/videos

Time Lapse
Time Lapse mode disables the PIR sensor, instead, it takes photos of record clips automatically at your programing of intervals. This has an advantage
for the further distance that is out of the PIR sensor’s range, such as big open areas or monitoring the flowering, sunrise, and sunset.

Time Lapse| On( 5s-23:59.59)/Off;
Default 5s| When setting the On option, the camera will automatically take photos/videos according to the set interval, regardless of whether the PIR sensor has detected any game. This is helpful when observing cold-blooded animals like snakes, or the process of flowering, etc. When the setting is Off, it’s will work with the PIR motion sensor.
---|---|---

Wi-Fi Feature
There 2 options methods to connect the camera with your phone, please Built-in Wi-Fi has a limited range, the max distance is 45 FT.
Default W-Fi SSID: Hunting 4K, password: 12345678
Preparation
Download the “Hunting 4K” App and install it on your phone

https:[//ligohk1.oss-cn-hongkong.aliyuncs.com/app/Hunting4k/Hunting4K.html](//ligohk1.oss-cn-hongkong.aliyuncs.com/app/Hunting4k/Hunting4K.html)

Option A Method
Manually turning on the camera’s built-in Wi-Fi, means you need to touch the camera, good for debugging or testing work.

Option B Method
Using the APP to active camera’s Wi-Fi, means you don’t need to touch the camera, just make sure the camera has power on and on “ON” mode.

Note:
• If you can’t find the Wi-Fi on your phone, try turning off your phone’s Wi- Fi and turn it on again, your phone will re-search the around Wi-Fi.
• The default setting of the camera’s Wi-Fi auto-off time is 1 minute, if there is no device connection within 1 minute after Wi-Fi is turned on, the Wi-Fi
will be automatically turned off. If you need more time to connect to the Wi- Fi, please update the Wi-Fi auto-off time settings in the camera and set a longer time.
• When the Wi-Fi connects successfully, if there is no operation during the set default Wi-Fi auto-off time, such as previewing photos, videos, etc., the camera will automatically disconnect after the default setting of Wi-Fi auto- off time.
• Once you don’t use the app, tap the “Exit” button on APP to disconnect and save the battery power.

Reset The Camera

if you need to change the default settings and cause issues, you can reset the camera recovery to the factory setting

Trouble Shooting / FAQs

The camera won’t take images

1. Please make sure that the SD card is not full, if the card is full, the camera will stop taking images.
2. Check the batteries to make sure that theyhave enough power for the camera to work.
3.  Make sure that the camera switch to the ON position.
4. Check the memory card can be used normally or not, it is recommended to format it the first time you use it.

The camera won’t power up

1.  Make sure that you have installed at least 4 batteries(1.5V) in the correct position.
2. Make sure that the switch is correctly in position, not OFF mode position
3.  Check the batteries has enough power, low power will cause it to fail to boot normally.

Battery life is shorter than expected

1. The battery power consumption rate largely depends on the surrounding environment and usage habits, such as insufficient light at night, frequent
   activities, long-term continuous photography, and video recording lights.

2. When the camera is working with full functions, such as infrared light, PIR motion sensor, lens sensor light assembly, etc., high-frequency activities will continue to activate the camera to work, accelerating power consumption.

3. You can try to adjust the PIR sensor settings and Time-lapse working mode to extend the use time.

Can’t find camera Wi-Fi when active built-in Wi-Fi via App

1. Check and make sure that you’re using the right app, this camera uses Hunting Camera”, you can download and install it on your phone, iOS, or Android.
2. The default setting of the camera’s Wi-Fi auto-off time is 1 minute, if there is no device connection within 1 minute after Wi-Fi is turned on, the Wi-Fi will be automatically turned off. If you need more time to connect to the Wi-Fi, please update the Wi-Fi auto-off time settings in the camera and set a longer time.
3. Try turning off your phone’s Wi-Fi and turn it on again, your phone will re-search the around Wi-Fi.

If your unit is still having trouble, please feel free to contact us via Email. Please be assured we will make things right for you.
Email: JOHCamService@gmail.com

Specifications

1920×1080@30pfs; 1280×720@30pfs; 720×480@30pfs; 600×360@30fps
Video Length| 5sec-3min
Shotting Numbers| 10-Jan
File Format| JPGIH.264 AVI
Lens| F=2.0, FOV=90°, Auto IR Cut
PIR Sensitivity| High/Normal/Low
PIR Sensing Angle| 120°
PIR Range| 850nm 75 feet (Below 77’F/25C)
Trigger Speed| 0.2s
Trigger Interval| 0sec–60min
IR Flash Range|  75 feet
Display| 2.4-inch color screen
External Memory| Max up to 512GB
Detection Angle| 120°
Password Protection| 4-Digit Code
---|---
Time Lapse Interval| 5sec-24h
Power Supply| 4x or Bx 1.5V AA Alkaline Batteries
Waterproof| IP66
Time Stamp Include| Serial No temperature and moon phrase
PC Interface| Mini USB2.0
Operation Temperature| -4’F-140F/-20’C-60’C
Operation Humidity| 5%-95%
Dimensions| 5.9×4.3×2.7 inch

Warranty and Disclaimers

Up to 1-year limited warranty, your product is warranted to be free of defects in materials and workmanship for 1 year after the date of purchase. This warranty does not cover damages caused by misuse, improper handling, and installation. In the event warranty service is needed, please contact JOHCamService@gmail.com
We hare no representations or warranties, either expressed or implied, by or concerning any content of these written materials or software, or for damages resulting from the use of the information contained therein. We reserve the right to alter the features and contents of this publication, hardware, or software without obligation or advance noticeWe are not responsible if you use the trail camera for illegal purchase We shall not be obligated to perform preventative maintenance installation, reinstallation, or maintenance. The illustrations in this manual are for instructions purposes only and may not represent the actual product exactly.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this  equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device does not contain any user-serviceable parts. Repairs should only be made by an authorized repair center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and will void your warranty and your authority to operate this device under Part 15 regulations. The shielded interface cable which is provided must be used with the equipment to comply with the limits for a digital device according to Subpart B of Part 15.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>