Shark NV105 Navigator Light Upright Vacuum Owner’s Guide

Shark NV105 Navigator Light Upright Vacuum

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK® NAVIGATOR™ VACUUM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK® NAVIGATOR™ VACUUM.

POLARIZED PLUG:

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. Do not force into the outlet or try to modify the plug to fit.

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY DO NOT USE OUTDOORS OR ON WET SURFACES.

GENERAL ELECTRICAL SAFETY:

1. Unplug from electrical outlet when not in use and before servicing.

2. DO NOT use vacuum with a damaged cord or plug.

3. DO NOT pull or carry vacuum by the cord.

4. DO NOT unplug by pulling on cord; to unplug, grasp the plug, not the cord.

5. DO NOT handle plug or vacuum cleaner with wet hands.

6. DO NOT run the vacuum over the power cord.

7. DO NOT close a door on the cord.

8. DO NOT pull cord around sharp edges or corners.

9. DO NOT leave appliance when plugged in.

10. Keep power cord away from heated surfaces.

11. Turn off all controls before plugging or unplugging vacuum cleaner.
    GENERAL USE:

12. Use only as described in this manual.

13. DO NOT put any objects into openings.

14. Keep your work area well lit.

15. Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers.

16. DO NOT place vacuum on unstable surfaces such as chairs or tables.

17. DO NOT allow young children to operate the vacuum or use as a toy.

18. Close attention is necessary when used by or near children.

19. DO NOT use vacuum cleaner if the appliance is not working as it should, has a damaged plug or cord, if the unit has been dropped, damaged, left outdoors or submerged in water. Return to EURO-PRO Operating LLC for examination, repair or adjustment.
    GENERAL CLEANING:

20. DO NOT run the vacuum over large-sized objects.

21. DO NOT pick up hard or sharp objects such as glass, nails, screws or coins that could damage the vacuum cleaner.

22. DO NOT pick up smoking or burning objects such as hot coals, cigarette butts or matches.

23. DO NOT pick up flammable or combustible materials such as lighter fluid, gasoline, kerosene or use in areas where they may be present.

24. DO NOT pick up toxic solutions such as chlorine bleach, ammonia or drain cleaner.

25. DO NOT use in an enclosed space where vapors are present from paint, paint thinner, moth-proofing substances, flammable dust or other explosive or toxic materials.

26. DO NOT vacuum up any liquids.

27. DO NOT immerse vacuum cleaner in water or other liquids.

28. DO NOT use outdoors or on wet surfaces; use only on dry surfaces.

29. Use extra care when cleaning on stairs.

30. Before turning on the vacuum:

    • Make sure that dust cup, and all filters are in place after routine maintenance.
    • Make sure that all components and filters are thoroughly dry after routine cleaning.
    • Only use filters and accessories provided by EURO-PRO Operating LLC [Failure to do so will void the warranty] HOSE ATTACHMENTS:

31. DO NOT put any object into openings. Do not use with any opening blocked. Keep free of lint, hair and anything that may reduce airflow.

32. DO NOT use if air flow is restricted; if the air paths, the hose or the extension tube become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.

33. Keep the end of the hose, wands and other openings away from face, body and loose clothing.

34. Keep rotating brush and suction openings away from hair, face, fingers, uncovered feet or loose clothing.

35. Only use manufacturer’s recommended attachments.

Getting Started

FIRST THING’S FIRST, YOU NEED TO KNOW WHAT’S IN THE BOX YOU JUST OPENED:

• A Handle
• B Extension Wand
• C Stretch Hose
• D Dust Cup
• E Hose Connector
• F Vacuum Body
• G Accessory Holder
• H Power Nozzle
  Optional tools are available for sale. To order additional parts or accessories go to www.sharkclean.com.

Assembly

YOUR SHARK® NAVIGATOR™ IS EASY TO ASSEMBLE:

1. Place your vacuum body upright on a level surface.

2. Insert the hose connector into the opening on the back of the vacuum body. (Fig. 1)
   NOTE: Once the hose connector has been inserted, it cannot be removed.

3. Insert the handle with the extension wand into the top of the vacuum until secure. (Fig. 2)
   

4. Insert the stretch hose into the hose connector on the back of the unit. Make sure that it snaps in place. (Fig. 3)

5. Store your on-board tools onto the accessory holder located on the back of the unit. (Fig. 4)
   NOTE: The accessory holder is removable. In order to remove or attach the accessory holder, you must remove the dust cup first. To remove the accessory holder, just hold the tab (a), rotate left and pull out. To replace, align the pins into the hinges (b) on the vacuum. Rotate it fully to secure. (Fig. 5)

6. When storing your vacuum, wind the power cord around the two cord holders and secure with cord clip. (Fig. 6)
   

7. There is a Quick Cord Release on the top cord holder. Simply turn to the left or right to release the power cord. To store the unit, the cord holder should be in the upright position.
   IMPORTANT: For suction to reach the power nozzle, the extension wand and stretch hose must be attached securely on the vacuum body.

8. TO CARRY THE VACUUM: With the unit in the standing position, lift by the Dust Cup Handle (carry handle).
   CAUTION: When lifting or carrying, DO NOT press Dust Cup release button ( ). 
   

Using the Vacuum

The height of your power nozzle has been optimized for easy pushing and superior cleaning on all floor types. There is no need to make any height adjustments as you transition to different floor & carpet types.

Note:

• Always hold the vacuum when using the hose to clean so that it does not tip over.
• DO NOT pull vacuum cleaner around by the hose.
• DO NOT over-extend the hose.

Your Shark® Navigator™ can be used to clean all surface types.

1. Plug in the vacuum.

2. Push the “Power” button. (Fig. 7)

3. Place your foot on the power nozzle and pull the handle back towards you. (Fig. 8)
   NOTE: This vacuum has a separate “Brushroll” button on the top of the vacuum. (Fig. 9)

4. CLEAN CARPETS: Engage the brushroll by pushing the “Brushroll” button to the “ON” position. The brushroll light will turn green. (Fig. 9)
   IMPORTANT: To protect your carpets, the brushroll will only turn on when you have pulled the handle back towards you and released the power nozzle.
   IMPORTANT: The brushroll indicator light on the power nozzle will illuminate solid red if there is a blockage. (Fig. 10) This feature is designed to protect your Lifetime Belt that powers your brushroll. See Checking for Blockages on page 10.
   

5. CLEAN BARE FLOORS: For cleaning bare floors or to clean with the hose, push the “Brushroll” button to the “OFF” position for suction only. The brushroll light will turn off. The brushroll will not spin in this mode. 
   

6. CLEAN ABOVE-FLOORS WITH HOSE:
   You can attach the accessories onto the handle or onto the extension wand for a longer reach.

   • a Stand the vacuum into upright position.
   • b To remove the handle only, press the handle release button. (Fig. 11)
   • c To remove the handle with the extension wand, press the extension wand release button on the back of the vacuum. (Fig. 12)
   • d Push the selected tool into the end of the handle or handle with extension wand for longer reach and begin cleaning.
     To order additional parts and accessories, go to www.sharkclean.com.
     

Emptying the Dust Cup Assembly

F or best results empty the Dust Cup Assembly after each use; or as needed during prolonged usage. or when it reaches the MAX fill line.
DO NOT OVERFILL.
Turn vacuum off before emptying.

TO EMPTY THE DUST CUP ASSEMBLY:

1. Press the Dust Cup release button ( ) and remove the dust cup from the vacuum. (Fig. 13)

2. Grip carry handle and press the bottom Dust Cup Door release button. (Fig. 14)

3. Option A: for Quick Empty: Insert Dust Cup Assembly deep inside trash receptacle to contain dust and debris. (Fig. 15)
   
   Press the bottom Dust Cup Door release button; tap container gently to dislodge and release dust and debris. Close the bottom door until it snaps in place.
   Important: If the Dust Cup Door does not swing open freely after pressing the release button, push the door open using the bottom door tabs.

4. Option B: For Allergy Sufferers: Wrap a trash bag around the Dust Cup Assembly leaving space at the bottom for the door to swing open. (Fig. 16)
   Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris.
   Close the bottom door until it snaps in place.
   Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the Dust Cup Assembly and trash bag outside.
   Note: It may become necessary to occasionally clean the metal screen inside the dust cup. To clean, press the top dust cup release button (Fig. 17), pull out the metal screen and remove any excess dirt. Then replace the metal screeen inside the dust cup and close the top lid. (Fig. 18)
   

Proper Care of Your Shark® Upright Vacuum

DO NOT put the filters in the washing machine or dishwasher.
NOTE: The material in the filter will discolor over time. This is NORMAL and will not affect the performance of the filter.
IMPORTANT: Loss of Suction may occur if foam filters are not cleaned every month. Rinse and allow to air dry completely. Foam filters may appear dirty after use – this is normal.
CAUTION: Unplug the vacuum while cleaning filters; failure to do so might result in electric shock.

CLEANING THE PRE-MOTOR FILTERS

1. Remove the dust cup.
2. Pull the 2 filters out from the top of the motor base. (Fig. 19)
3. Rinse the filters thoroughly in lukewarm water until the water runs clear.
4. Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.
5. Place the felt filter in first, then the foam filter.
6. Replace the dust cup.

CLEANING THE POST-MOTOR FILTER

1. Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum. (Fig. 20)
   

2. Remove the filter from the frame and wash the filter under the tap using lukewarm water.

3. Allow the filter to air dry for 24 hours. Do not use a hair dryer or other heating methods to dry.

4. Once the filter is dry, replace it back into the vacuum.

5. Replace the cover by inserting the two tabs into the holes at the top and and then swinging the cover down until it clicks into place.
   NOTE: Filters may appear dirty but frequent cleaning of these is not necessary. See maintenance schedule above.

Troubleshooting

WARNING: To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks.

PROBLEM                                POSSIBLE REASONS & SOLUTIONS

Vacuum will not run.

| Check to see if the vacuum is plugged in properly. Check the circuit breaker/fuse.

Check the On/Off button.

Vacuum is not picking up dirt.

Airflow is restricted. No suction or light suction.

| ****

Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.)

Dust cup may be full; empty dust cup.

Check hose and hose connections for blockages; clear blockages if required.

If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)

Brush roll does not turn on.

| Press the “Brushroll” button to the “ON” position. The brushroll light near this button will illuminate green when “ON”.

Place your foot on the floor brush and pull the handle back to engage the brushroll.

If the red light on the power nozzle is illuminated, see the section on Checking for Blockages.

Vacuum turns off on its own.

| ****

This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, perform the following steps to restart the motor thermostat:

1. Press the “Power” button to the (Off) position.

2. Unplug the vacuum.

3. Empty the dust cup and clean filters. (See “Maintenance” sections for instructions.)

4. Check for blockages in hose, accessories and inlet openings. (See “Checking for Blockages” for instructions.)

5. Allow the unit to cool for a minimum of 45 minutes.

6. Plug in the vacuum.

7. Press the “Power” button to the (On) position to restart the vacuum.

Note: If vacuum still does not start, contact Customer Service at:

1-800-798-7398. 

Checking for Blockages

Blockages may cause your vacuum to overheat and shut down. If this occurs, clear the blockages, then follow the instructions for Resetting the Motor Thermostat on page 11.
IMPORTANT: Never insert sharp objects into any opening to clear an obstruction. Damages caused while clearing or attempting to clear blockages are not covered under your product’s limited warranty.
Unplug the vacuum before checking for blockages.

Reassemble all parts securely before operating vacuum.

1. DUST CUP AIR DUCT: Stand vacuum upright. Remove Dust Cup Assembly and empty Dust Cup if necessary. Check Air Duct behind Dust Cup for clogs; clear before replacing Dust Cup Assembly. (Fig. 21)
2. HOSE INTAKE OPENING: Hold the top of the hose access door and pull firmly to remove. Slide the knob to the center and pull out the hose. (Fig. 22) Remove any obstructions and push the hose back in. Slide the knob to the left and snap the hose access door shut.
3. HOSE: Disconnect the Stretch Hose by gently pressing the tabs together and pulling away from the hose connector. Remove hose from both the unit and handle ends. (Fig. 23) Inspect the length of the hose and remove any obstuctions.
   

Maintenance

Resetting the Motor Thermostat Your Shark® Navigator™ is equipped with a protective Motor Thermostat. If the motor should overheat, the thermostat shuts off the power.

TO RESET THE MOTOR THERMOSTAT:

• Press the Power Button to turn the unit “Off”.
• Unplug the vacuum.
• Check for clogged hose or filter; unclog hose and replace filter.
• Refer to Checking for Blockages on page 10.
• Wait 45 minutes for vacuum to cool; then plug in the vacuum.
• Press the Power Switch to start the vacuum.
  NOTE: If vacuum still does not start, contact Customer Service at: 1-800-798-7398.

Get even more cleaning from your Shark® Navigator™ by checking out our cleaning accessories assortment at www.sharkclean.com.
Bookmark the page and check back often to take advantage of the latest products, promotions and prices!

ADDITIONAL ACCESSORIES (AVAILABLE FOR PURCHASE):

• MULTI-TOOL
  Convenient crevice tool and dusting brush in one.

• PET/UPHOLSTERY TOOL
  Removes hair from upholstery and stairs.

• CREVICE TOOL
  Reach deep into narrow spaces and clean between cushions, under radiators and baseboards and in hard to reach crevices and corners.
  NOTE: Some accessories may be included with your purchase.

To order Additional Parts & Accessories go to www.sharkclean.com.

Euro-Pro Three-Year (3) Limited Warranty

EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of three (3) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to:

• U.S: EURO-PRO Operating LLC For customer service support call 1-800-798-7398 or visit www.sharkclean.com
• Canada: EURO-PRO Operating LLC 4400 Bois Franc, St. Laurent, Québec H4S 1A7 If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $16.99 to cover the cost of return shipping and handling must be included.* Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC. This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

Product Registration

Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address. The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

FAQs

What is the difference between Shark NV105 Navigator Light Upright Vacuum and NV100 Navigator Light Upright Vacuum?****

The only difference between Shark NV105 Navigator Light Upright Vacuum and NV100 Navigator Light Upright Vacuum is the color.

What kind of warranty comes with the Shark NV105 Navigator Light Upright Vacuum?****

Shark NV105 Navigator Light Upright Vacuum comes with 2 year warranty.

How do you use a Shark Navigator vacuum?****

To remove the handle, press the handle release button (or handle with extension wand). 2 Place your foot on the nozzle, press the red nozzle release button (h), and then raise the canister. 3 Attach the necessary cleaning tools.

Does the Shark Navigator vacuum have a belt?****

The belt for the vacuum is meant to endure for roughly 7 years. To keep the vacuum in top functioning condition, the belt must be replaced. This replacement manual provides instructions for changing the vacuum’s belt.

Does Shark Navigator need a filter?****

The Shark Navigator’s user guide suggests cleaning the post-motor filter once a year and the pre-motor filters every three months.

Can Shark Navigator vacuum water?****

None at all. The motor will be completely submerged in water, thus it doesn’t work like a wet vacuum. With water, you’ll need a wet vacuum.

Does the Shark Navigator have good suction?****

For low-pile carpet, the Shark Navigator Lift-Away Speed works quite well. It effortlessly removes pet hair and does a fantastic job sucking up both small and huge detritus. As long as you clean its filters in accordance with manufacturer guidelines, its bagless design incurs very little ongoing expense.

When did the Shark Navigator vacuum come out?****

In the fall of 2010, the initial Navigator was released. Although it wasn’t the first Shark vacuum, the company was still not well-known.

What causes a vacuum to lose suction?****

Cleaners are rather straightforward machines. For the vacuum to generate a suction force that lifts debris, they need to provide power. Thus, incorrect height settings, stuck rollers, bad gaskets, damaged vacuum belts, packed bags, and blocked hoses are the typical culprits of suction loss.

How many filters are in a Shark Navigator vacuum?****

One HEPA filter, three foam filters, and three felt filters are included in the box.

Video

Download PDF Link;Shark Navigator Light Upright Vacuum pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>