OFX PBX-100 Portable Speaker User Manual
- June 6, 2024
- OFX
Table of Contents
User Manual for PBX-100 Portable Speaker
THANK YOU FOR PURCHASING OUR SPEAKER. PLEASE READ THE MANUAL CAREFULLY BEFORE
OPERATING.
IMPORTANT SAFETY MEASURES
Before using this machine, please read all the safety and operating
instructions. Please adhere to all the instructions herein, and save this
information in a safe place for future use.
- Please ensure the power cord for this unit is out of the path of foot traffic. Do not place heavy objects on the power cord as it will cause damage to the cord. Always firmly grasp the plug and pull the plug from the power supply, never yank the cable in order to pull out the plug. Avoid the use of an extension cable.
- Ventilation: This unit should be placed in a well-ventilated space where it has no less than 10cm ventilation space on either side of it. Do not cover the unit with a cloth or blanket. Do not put it on a bed, sofa, or carpet as this will stifle the ventilation of the unit.
- Casing Dismantling: DO NOT dismantle the casing. There are no usable parts inside the unit. Make use of a service center in order to have your unit repaired.
- Should the unit emit any smell or smoke, immediately turn off the power supply? Take the unit to the service center from which you bought it for repairs.
FEATURES
- Bluetooth & TWS function
- Plays Mp3 files stored in SD card/USB drive/external audio device.
- FM radio, remote control
- Guitar/Microphone input
- 5 Band graphic equalizer
- Built-in 12V/7A rechargeable batter
- Microphone priority on/off switch
- Super dynamic sound speaker
CONNECTING
- This setting applies to AC 110V-240V, 50/60Hz
- AC power: the battery can be charged when connected to AC power. The red light on the battery is charging, it will change to green once the battery complete charge.
- The internal battery will be charged even device switch off when plugged into AC power
- Speaker battery can be charged using 12V external car battery as well (connect cable not included) by “DC 12V input”. Please make sure “+” and “-” are in the right connection.
- Adjust function keys to your personal audio preference.
BLUETOOTH INSTRUCTION
Change the mode into”BLUE”, the Bluetooth sign light twinkles, and the speaker will give an alarm. Ensure you enable the Bluetooth function on your Bluetooth device. Search for Bluetooth connection until you find the device model and pair
TWS CONNECTION
In Bluetooth mode, press the TWS button and hold it down for three seconds, the primary speaker will sound an alarm and the screen will show “BTST”. The secondary speaker switch to Bluetooth mode will automatically connect to the primary speaker and the screen will show “BT”.
BATTERY & CHARGING
- The units take approximately 8 hours to fully charge. It will automatically begin charging once the power cord is connected.
- If the battery power is low may cause sound distortion or stop play, pls charge the battery on time.
- To maximize the battery’s lifespan, please charge the battery immediately. When the unit is not used for prolonged periods of time, the battery will gradually lose its power. It is recommended to fully charge the battery at least every 30days.
- To save battery, please power off once stop using.
REMOTE CONTROL
CONTROL PANEL
-
POWER ON/OFF SWITCH
-
LED LIGHT ON/OFF SWITCH
-
POWER INPUT
-
VOLUME: MASTER VOLUME ADJUST
-
BASS: BASS ADJUST
-
MIC. ECHO: ECHO ADJUST
-
MIC BASS: MICROPHONE BASS VOLUME ADJUST
-
MIC TREBLE: MICROPHONE TREBLE VOLUME ADJUST
-
MIC VOL.: MICROPHONE VOLUME ADJUST
-
GUITAR VOL.: GUITAR VOLUME ADJUST
-
MIC PRI.: MICROPHONE PRIORITY ON/OFF SWITCH
-
GUITAR IN: GUITAR INPUT
-
MIC IN: MICROPHONE INPUT
-
FM ANTENNA
-
USB PANEL FUNCTION
MODE: MODE SELECT
REC: RECORD: INSERT THE USB MEMORY/SD CARD AND PRESS THIS BUTTON TO START RECORDING. PRESSING THE BUTTON AGAIN TO STOP. REP: REPEAT
PLAY/PAUSE; FM STATION AUTO SEARCHING TWS: ON/OFF SWITCH(PRESS AND HOLD)
PREVIOUS
NEXT -
EQUALIZER
-
12V EXTERNAL INPUT
-
AUX INPUT
TRUE WIRELESS STEREO
CONNECT
PAIR 2 PBX-100
STEP 1
MODE
Push the Mode Button on both speakers until speakers are in Bluetooth Mode. The screen will display the word “Blue”
STEP 2
When both speakers are in Bluetooth mode, push and hold the TWS button for 3 seconds. You will hear a beep. Next time you put both speakers in Bluetooth mode at the same time, speakers will connect automatically.
STEP 3
On your device, turn your Bluetooth settings “ON”, you will then select “QFX PBX-100”. Enjoy TWS (True Wireless Stereo) sound from your phone via Bluetooth.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>