INFINITY X3 Smart Chair Massage Chair Installation Guide
- June 6, 2024
- Infinity
Table of Contents
Smart Chair X3 Massage Chair
Assembly Guide
www.infinitymassagechairs.com/assemblytutorials to watch an assembly video.
http://www.infinitymassagechairs.com/assembly-tutorials
Step 1:
Carefully check box contents to the detail below, making sure all contents
are accounted for.
If anything is missing, please contact INFINITY at
603-910-5000. Do not return to the
place of purchase.
Step 2:
Connect the chair power cord to a grounded 110V electrical outlet and plug it
into the respective port on the backside of the base of the chair. Flip the
main power switch to on.
Step 3:
Plug the remote control cord into the remote control port also located on the
backside of the base of the chair. Ensure the arrow on the top of the remote
control cord is facing up . Screw on to fasten. Do not force.
Step 4:
Press the power button on the remote control once to turn it on, then once
more to bring the chair into an upright position. To protect you and the
remote control during assembly, unplug it from the chair and switch the main
power off.
Step 5:
Attach the back cushion by draping it over the top of the chair body and
zippering it to the zipper located on the top of the back of the chair body.
Step 6:
On the left-hip side, locate and connect the air hose to the air nozzle on the
body of the chair; also connect the power input to the chair body power cord
and fasten. On the right-hip side, locate and connect the three air hoses from
the back cushion to their corresponding air nozzles based on the numbers
labelled on each. Zipper the closure between the Seat Cushion and Back
Cushion.
Step 7:
Remove the outer components of the two white bushings located on the side of
the chair, leaving the inner components on the chair body. Set aside, take
note that the larger bushing goes in the upper rear position and the smaller
one goes in the lower front position.
Step 8:
Prepare Arm Panel for assembly by opening zipper on the bottom of the panel.
Pull flap open to reveal plastic cover panel. Remove the plastic cover panel
from the arm panel.
Step 9:
Position Arm Panels on the corresponding side of the chair, such that the Arm
Panel Lock is at the back. Locate and attach the two Arm Panel air hoses to
their respective air nozzles on the chair, making sure to match up numbers.
Step 10:
Align the two pins on the Chair Body with the slots on the Arm Panel, making
sure the air hoses are out of the way. Use your body for support to hold it in
place. Re-attach the outer components of the front bushing first, then the
rear. Hand screw into place.
Step 11:
Shimmy the arm panel upward and towards the front of the chair until the pin
on the side of the chair body secures into the arm panel lock.
Step 12:
Using the provided screwdriver, tighten both the front and rear bushings
firmly into place. Cover the opening using the provided plastic cover panel,
then zipper the faux leather cover flap shut.
Step 13:
Before attaching the shoulder panels, ensure the airbag is toward the front of
the chair. Connect the red plug until it clips then connect the white plug
until it clips.
Step 14:
Slide the metal joint pins into the opening on the chair body until the
Shoulder Panel secures into place.
Step 15:
On the inside of the shoulder panel, locate and open the small sliding door
where you will see a screw. Screw-in clockwise tightly and then close the
sliding door when the shoulder panel is fully secured
Step 16:
Remove the footrest from its packaging and position it in front of the main
chair body. Connect the footrest by attaching the electrical plug from the
footrest into the port on the body of the chair. Ensure the thumb release is
facing up and push in until it snaps. Slide the air hose onto the white air
nozzle.
Step 17:
Lift up and pull back flap on the footrest. Slide the footrest in and shift it
until the mounting bracket is properly aligned with the screw holes located on
the body of the chair. Insert the hex screws through the screw holes to fasten
the footrest to the body of the chair. Repeat on another side. Tighten with
Hex Key.
Final Check:
Plug the remote cord back into the input port located on the back of the base
of the chair. Ensure the arrow on the top of the input jack is facing up.
Remote Pouch
Attach remote pouch using velcro found underneath the right armrest
Review chair for smooth operation. If things are not operating correctly,
review all assembly steps. Call Infinity support at
1-603-910-5000 if you need live US-
based support.
If you wish to use an APP to control the chair, download it from the Apple or
Google app store and follow the pairing instructions found within the APP.
You are done; time for a Massage!
Go to
www.infinitymassagechairs.com/warranty
to register your chair
and enable full support for your warranty.
72 Start Road, Seabrook, NH 03874
603-910-5000
www.infinitymassagechairs.com
Version 1.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>