Tiinlab EO002-I omthing AirFree Plus TWS Headphones User Guide

Tiinlab EO002-I omthing AirFree Plus TWS Headphones

AirFree Plus TWS Headphones User Guide

Please read the user guide thoroughly before use of this product and retain it properly for future reference.

Package Contents

• AirFree Plus TWS Headphones

• Type-C Charging Cable

• Silicone Ear Tip 3 Pairs ( S/M*/L )

• User Guide

Pre-installed with the earbuds
The illustrations of products, accessories and UI in the user manual are for reference only. Actual product may vary due to product updates and upgrades, please refer to the actual product.

Charging

• Charge the earbuds
  Put the earbuds back into the charging case, they will automatically start charging.

• Charge the charging case with Type-C Charging Cable
  LED indicator on the case will stay white while charging, and goes out when fully charged.

Battery Status

• Earbuds’ battery status
  After being connected to your phone, you can check the earbuds’ battery on the status bar of the phone.
  Note: The status bar of the phone only shows the primary earbud’s battery status.
  This function is not supported by some phones.

• Charging case battery status
  Cannot be checked on the connected phone.

• Power Off
  When the earbuds’ battery is too low to work, the LED indicator on earbuds will flash white for 1 second and then the earbuds automatically turn off.
  Note: Please put the earbuds back into the charging case when not using to extend the service life and prevent losing them.

Placement
Take the earbuds out of the charging case and wear them as the L/R labels on the earbuds.

Standby
Put the earbuds back into the charging case and close the lid, they will automatically turn off and start charging.

Power On & Primary / Secondary Switch

1. The first time you open the case, the earbuds will automatically turn on and then enter TWS pairing mode ( the right one is the primary earbud by default ).
   The earbuds will enter Searching & Pairing mode after connected in TWS mode.

2. The secondary earbud will become the primary once you put the primary earbud into the case.

3. If the primary earbud goes beyond the connection range and the secondary is close to the phone, then it will become the primary.

4. The secondary earbud will become the primary if the primary turns off because of low battery.

Enter pairing mode for the first time

Once you open the case and take out the earbuds, they will enter TWS pairing mode, and after successfully connected, the earbuds will enter Searching &
Pairing mode (Pairing name: omthing Airfree Plus). The LED on secondary earbud will flash white once every 7 seconds while the LED on the primary earbud will flash white twice every second, and the whole process will last 5 minutes. If not connected to any device within 5 minutes, the earbuds and LED will turn off.
(Put the earbuds back into the case and open the lid again, the earbuds will automatically turn on.)

Re-connection
Open the case, the LED indicator on the earbuds that have been taken out will flash white for 1 second. The earbuds will first enter TWS pairing mode and then re-connect to the last connected device.

Bluetooth Disconnects Due to Out-of-Range

1. When two earbuds go beyond the connection range simultaneously, there is no primary/secondary switch; the primary earbud will automatically re-connect to the phone after returning to the connectable range within 5 minutes; if not,the two earbuds will enter Sleep Mode.
2. When the primary earbud goes beyond the connection range, if the secondary earbud is close to the phone, it will automatically become the primary. If the prior primary returns to the connection range within 5 minutes, it will become the secondary earbud and connect to the device; if not, it will turn off.
3. When the secondary earbud goes beyond the connection range, the primary keeps working. If the secondary earbud returns to the connection range within 5 minutes, it will re-connect to the primary and the device; if not, it will turn off.

Bluetooth Connection Times Out
If there is no connection or operation within 5 minutes after entering pairing mode, the earbuds and LEDs will automatically turn off. (For reconnection, please put the earbuds back into the case and then take them out.)

Disconnect to the Device
Cut off the Bluetooth connection on the phone, the earbuds will enter into a TWS mode and then re-enter pairing mode.

Clear Connection History (Only Available in TWS Mode)
Long press the touch control area of two earbuds for 7 seconds to clear connection history when they are in the case. After taking earbuds out of the case, the LED on the primary earbud will flash white twice every second, and the LED on the secondary earbud will flash white once every 7 seconds. If there is no connection or operation within 5 minutes, the earbuds and LEDs will automatically turn off; if connected, the LED on two earbuds will flash white once every 7 seconds.

Touch Controls

Answer call / Hang Up
Double-tap the L/R earbud (also available in Mono mode)

Place the Current Call on Hold and Answer Another Call
Double-tap the L/R earbud (also available in Mono mode). When you answer the second call, the first caller is put on hold.

End the Current Call and Answer the Waiting Call
Double-tap the L/R earbud

Music Playback
Play/Pause: Double-tap the right earbud (also available in Mono mode)

Voice Assistant
Doube tap the left earbud to activate

Specifcations

• Model: EO002-I
• Weight: 42 g
• Charging Port: Type-C
• Speaker Impedance: 32
• Input: 5V 1A
• Output: 5V 150mA
• Bluetooth Version: Bluetooth 5.2
• Bluetooth Range: 10 m (Open space)
• Bluetooth Protocol: BLE / HSP / HFP / A2DP / AVRCP
• Supported Codecs: AAC / SBC
• Case Battery Capacity: 550mAh
• Charging Time: 1.5 hours
• Earbuds Playtime (A Single Full Charge): Approx. 4 hours
• Total Playtime of Earbuds and Case: Approx. 18 hours

Parameters listed are based on laboratory tests.

Safety Information

1. Never disassemble the headphones. There are no user-serviceable parts inside.
2. Do not expose the headphones to temperatures below 32 °F (0 °C) or to temperatures above 113 °F (45 °C).
3. Do not use the headphones in a thunderstorm storm. This could prevent the headphones from working properly, and also increase your chance of being electrically shocked.
4. Do not use oil or any volatile liquid to clean this product.
5. Do not listen at high volumes for extended periods of time.
6. Do not use the headphones in trafc. Do not use the headphones any time it would be dangerous to be unaware of noises around you.
7. Adult supervision is required for children of age 6 and under.
8. Do not expose batteries or battery packs to excessive heat such as sunshine, fire, or the like.

CE

Declaration of Conformity Hereby, Tiinlab Corporation declares that the radio equipment type AirFree Plus TWS Headphones of EO002-I is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:www.omthing.com
RF exposure information: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Radiation Exposure Statement Power is so low that no RF exposure calculation is needed.
Operation Frequency/Max. EIRP: 2402-2480MHz, Max. EIRP is 9.72dBm.

Warning
Replacement of a battery with an incorrect type that can defeat a safeguard (such as catching fire, explosion, leakage of corrosive electrolyte etc);
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and A battery subjected to extremely low air pressure that may result in an explosion
or the leakage of flammable liquid or gas.

The symbol indicates DC voltage.

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

FCC

The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction. Federal
Communication Commission (FCC) Radiation Exposure Statement Power is so low that no RF exposure calculation is needed.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changesto this equipment. Such modifications or changes could void the user’s authority to operate the equipment.
   NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard(s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d’interférences, et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais

fonctionnement de l’appareil. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

References

• omthing.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>