SHARP HT-SB150 2.0 Soundbar Home Theatre System User Manual

: June 6, 2024
: Sharp

sharp

SHARP HT-SB150 2.0 Soundbar Home Theatre System

Important safety instructions

Please, read these safety instructions and respect the following warnings before the appliance is operated:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude as to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
In order to prevent fi re always keep candles and other open flames away from this product
Always follow basic safety precautions when using this applience, especially when children are present.
Children should be supervised to ensure that they do not play with the appliance.
Do not damage the power cord, neither do not place any heavy objects on it, do not strech it or bend it. Also do not attach extension cables. Damage to the power cord may occur fi re or electric shock.
If the supply cord is damaged, it must be replaced by the manufacturer, a service agent or similarly qualied persons in order to avoid a hazard.
Ensure that the unit is plugged into an AC 100-240V 50/60Hz power outlet. Using higher voltage may cause the unit to malfunction or even fi re catching.
If the power plug does not fi t into your outlet, do not force the plug into an electri-cal socket if it does not fi t.
Turn off the unit before unplugging it from power source to completely switch it off .
Do not disconnect or connect the power cord with wet hands. It may cause an electric shock.
Disconnect the power cord if it is not used for a long time.
Ensure that the mains plug is always easily accessible.
This product does not contain any parts that are serviceable by the user. In case
of a fault, contact the manufacturer or authorised service department. Exposing the internal parts inside the device may endanger your life. The manufacturers guarantee does not extend to faults caused by repairs carried out by unauthorised third parties.
Do not use this product immediately after unpacking. Wait until it warms up to room temperature before using it.
Ensure this product is used in moderate climates only (not in tropical/subtropical climates).
Place product on a fl at, stable surface that is not subject to vibrations.
Ensure the product and its parts is not overhanging the edge of the supporting furniture.
To reduce the risk of ﬁre, electric shock or damage to this product, do not expose it to direct sunlight, dust, rain and moisture. Never expose it to dripping or splashing and do not place objects ﬁlled with liquids on or near the product.
Do not place objects fi lled with liquids, such as vases, on the apparatus.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
Do not place the product where the humidity is high and ventilation is poor.
Ensure a minimum distance of 5 cm around the apparatus for suffi cient ventilation. Do not block any ventilation openings of this product. Always ensure that the ventilation openings are not covered with items such as newspapers, table-cloths, curtains, etc.
NEVER let anyone, especially children, push anything into holes, slots or any other openings in the unit’s casing as this could result in a fatal electric shock.
Storms are dangerous for all electric appliances. If the mains or aerial wiring is struck by lightning, the appliance might get damaged, even if it is turned off . You should disconnect all the cables and connectors of the appliance before a storm.
Unplug the power cable from the power source before cleaning the appliance.
Use a soft and clean rag to clean the outside of the unit. Never clean it with chemi-cals or detergent.
Observe the correct polarity when inserting the batteries.
Do not expose batteries to high temperatures and do not place them on locations where the temperature might increase quickly, e.g. near the fi re or on the direct sunshine.
Do not expose batteries to excessive radiant heat, do not throw them into the fi re, do not disassemble them and do not try to recharge un-rechargeable batteries. They could leak or explode.
Never use diff erent batteries together or mix new and old ones.
When the Remote Control is not to be used for a long time (more than a month), remove the battery from the Remote Control to prevent it from leaking.
If the batteries leak, wipe away the leakage inside the battery compartment and replace the batteries with new ones.
Do not use any batteries other than those specied.
Do not ingest battery, chemical burn hazard
If the battery is swallowed, it can cause severe internal burns in just 2 hours and lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Disposal of this equipment and Batteries

Do not dispose of this product or its batteries as unsorted municipal waste. Return it to a designated collection point for the recycling
of WEEE in accordance with local law. By doing so, you will help to conserve resources and protect the environment.
Most of the EU countries regulate the disposal of batteries by law. Contact your retailer or local authorities for more information.
The shown above appears on electrical and electronivcal equipment and batteries (or the packaging) to remind users of this. If “Hg” or ‘Pb’ appears below the symbol, this mean that the battery cantains traces of mercury (Hg) or lead (Pb), respectively.
Users are requested to use existing return facilities for used equipment and batteries.

CE Statement:

Hereby, UMC Poland Sp. z o.o. declares that this audio device is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU. The full text of the EU declaration of conformity is available by following the link https://www.sharpconsumer.eu/documents-of-conformity

Accessorie

s1x Remote control
1x User guide
1x Quick start guide
1x Warranty leafl et
1x UK power cord
1x EU power cord
1x Set of wall-mounting screws
4x Silicone feet
2 x AAA battery

Controls

control

Display screen
Remote sensor
Standby – Switch the unit between ON and STANDBY mode.
Source – Select the play function.
Volume +/- – Increase/decrease the
volume level.

Inputs/Outputs

input -output

ARC Socket – Connect to a TV via HDMI cable.
OPTICAL Socket – Opticial input jack.
LINE IN Socket – Connect to an external audio device.
UPGRADE Socket – The USB socket is for service only. It is not designed to charge smartphones, tablets or similar devices.
AC~ Socket – Connect power cord.

Remote control

Switch the unit between ON and STANDBY mode.
Select the Bluetooth mode. Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device.
3. – Select the play function.
VOL +/- – Increase/decrease the volume level.
Skip to previous/next track in Bluetooth mode.
Play/pause/resume playback in Bluetooth mode.
(MUTE) Mute or resume the sound.
BASS +/- – Adjust bass level.
TRE +/- – Adjust treble level.
EQ – Select a preset sound mode.

RC OPERATIONS

The provided Remote Control allows the unit to be operated from a distance.

Even if the Remote Control is operated within the eff ective range of 6m, remo-te control operation may be impossible if there are any obstacles between the unit and the remote control.
If the Remote Control is operated near other products which generate infrared rays, or if other remote control devices using infra-red rays are used near the unit, it may operate incorrectly. Conver-sely, the other products may operate incorrectly.

ReOperation

BATTERY INSTALLATION

Press and slide the back cover to open the battery compartment of the remote control.
Insert two AAA size batteries (included). Make sure the (+) and (–) ends of the batteries match the (+) and (–) ends indicated in the battery compartment.
Close the battery compartment cover.

First time installation

Placement and Mounting

1st time installing

A: Normal Placement (A1 – Attach the silicone feet to the bottom of the soundbar. Place Soundbar on leveled surface in front of TV.)
B: Wall Mounting

Wall Mounting

NOTE:

Installation must be carried out by qualifi ed personnel only. Incorrect assembly can result in severe personal injury and property damage (if you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing that may be buried inside the wall). It is the installer’s responsibility to verify that the wall will safely support the total load of the unit and wall brackets.
Additional tools (not included) are required for the installation.
Do not overtighten screws.
Keep this instruction manual for future reference.
Use an electronic stud fi nder to check the wall type before drilling and mounting.

Wall Mounting

Drill 2 parallel holes (Ø 6mm) in the wall. The distance between the holes should be 650 mm.
- Firmly fi x one dowel into each hole in the wall and then insert screws into them.
Leave a 4mm gap between the wall and the screw’s head. Lift the unit with the attached wall brackets over the heads of the screws and slot into place.

Connections

connection

HDMI ARC input
The ARC (Audio Return Channel) function allows you to send audio from your ARC- compliant TV to your sound bar through a single HDMI connection. To enjoy the ARC function, please ensure your TV is both HDMI-CEC and ARC compliant and set up accordingly. When correctly set up, you can use your TV remote control to adjust the volume output (VOL +/- and MUTE) of the sound bar.

Connect the HDMI cable (not included) from unit‘s HDMI (ARC) socket to the HDMI (ARC) socket on your ARC com-pliant TV. Then press the remote control to select HDMI ARC.

TIPS:

Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and ARC must be set to On.
The setting method of HDMI-CEC and ARC may diﬀ er depending on the TV. For details about ARC function, please refer to your TV owner’s manual.
Only HDMI cables of version 1.4 or higher can support the ARC function.

connection 1

OPTICAL input

Use the optical cable to connect the optical input of this soundbar to the optical output of VCD, CD, VCR, DVD player.

connection 2

LINE IN

Use a RCA to 3.5mm audio cable (not included) to connect the TV’s audio output sockets to the LINE IN socket on the unit.
Use a 3.5mm to 3.5mm audio cable (not included) to connect the TV’s or external audio device headphone socket to the LINE IN socket on the unit.

TIP:

When you use the headphone output on the TV set, you will be able to adjust the volume level directly using the TV remote control.

Line in

Connect to Power

Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.
Before connecting the AC power cord, ensure you have completed all other connections.
Connect the mains cable to the AC IN Socket of the unit and then into a mains socket.

Basic Operation

Standby/ON

When you fi rst connect the unit to the main socket, the unit will be in STAND-BY mode.
Press the button on the remote cont-rol to switch the main unit ON or OFF.
Disconnect the main plug from the main socket if you want to switch the unit oﬀ completely.
- When the unit has no input signal for over 15 minutes, it will automatically switch to Standby mode.

Select Modes

Press the button on the unit repeatedly or press the / button on the remote control to select the desired mode.

Adjust the Volume

Press the + / – buttons on the unit or on the remote control to adjust the volume.
If you wish to turn the sound oﬀ , press the button on the remote control. Press the button again or press the +/- buttons on the unit or on the remo-te control to resume normal listening.

Select Equaliser (EQ) Eﬀect

While playing, press the EQ button on the remote control to select between preset equalisers: Music – Eq1 appears on the display (recommended for listening to music), Movie – Eq2 appears on the display (recommended for view-ing movies), NEWS – Eq3 appears on the display (recommended for listening to NEWS), Cust – Cust appears on the display (recomended for personal bass/treble settings).

NOTE: Bass/Treble setting is available only in custom preset.

LINE IN/OPTICAL/HDMI ARC

Ensure that the unit is connected to the TV or audio device.
While in ON mode, press the button on the unit repeatedly to select the desired mode.
Operate your audio device directly for playback features.
Press the +/– button to adjust the volume to your desired level.

TIP:

While in HDMI ARC/OPTICAL mode, if there’s no sound output from the unit, you may need to activate PCM signal output on your source device (eg. TV, DVD or Blu-ray player).

Bluetooth Operation

Pair Bluetooth-enabled Devices.

The fi rst time you connect your Bluetooth device to this player, you need to pair your device to this player.

NOTE:

The operational range between this player and a Bluetooth device is approximately 8 meters (without any object between the Bluetooth device and the unit).
Before you connect a Bluetooth device to this unit, ensure you know the device’s capabilities.
Compatibility with all Bluetooth de-vices is not guaranteed.
Any obstacle between this unit and a Bluetooth device can reduce the operational range.
If the signal strength is weak, your Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically.
Turn on the soundbar by pressing the standby button.
Press the button on the unit repeatedly or button on the remote control to select Bluetooth mode. You are in bluetooth mode when you see letters „bt“ fl ashing on the display.
Enter the Bluetooth search mode on the device you wish to connect to the soundbar.
Select SHARP HT-SB150 from the list.
Your device and the soundbar will now be connected.
- To disconnect your device, switch off the Bluetooth connection or hold down button on the remote control for 3 seconds

TIPS:

Enter „0000“ for the password if necessary.
The player will also be disconnected when your device is moved beyond the operational range.
If you want to reconnect your device to this player, place it within the opera-tional range.
If the device is moved beyond the operational range, when it is brought back, please check if the device is still connected to the player.
If the connection is lost, follow the instructions above to pair your device to the player again.

Listen to Music from Bluetooth Device

If the connected Bluetooth device supports Advanced Audio Distribution Profi le (A2DP), you can listen to the music stored on the device through the soundbar‘.
If the device also supports Audio Video Remote Control Profi le (AVRCP), you can use the soundbar‘s remote control to play music stored on the device.

Pair your device with the player.
Play music via your device (if it supports A2DP).
Use supplied remote control to control play (if it supports AVRCP).

To pause/resume play, press the button on the remote control.
To skip to a track, press the / buttons on the remote control.

Troubleshooting

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, review the following before requesting service.

No power

Ensure that the AC cord is properly connected. Ensure that there is power at the AC outlet. Press standby button on the remote control or soundbar to turn the soundbar on

No sound

Increase the volume. Press Volume Up on the remote control or on the right side of the soundbar. Press on the remote control to ensure the soundbar is not muted. Press source buttons to select a diﬀ erent input source. When using either of the Digital input, if there is no audio:

Try setting the TV output to PCM or
Connect directly to your Blu-ray/other source, some TVs do not pass through digital audio.

Your TV may be set to variable audio output. Confi rm that the audio output setting is set to FIXED or STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information. If using Bluetooth, ensure that the volume on your source device is turned up and that the device is not muted

Remote control does not work.

Before you press any playback control button, fi rst select the correct source. Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/-) aligned as indicated Replace the battery. Aim the remote control directly at the sensor on the front of the unit.

I hear buzzing or humming

Ensure all cables and wires are securely connected. Connect a diﬀ erent source device (TV, Blu-ray player, etc) to see if the buzzing persists. If it does not, the problem may be with the original device. Connect your device to a diﬀ erent input on the soundbar.

I can’t fi nd the Bluetooth name of this unit on my Bluetooth device

Ensure the Bluetooth function is activated on your Bluetooth device. Re-pair the unit with your Bluetooth device.

This is a 15 mins power oﬀ function, one of the ERPII standard requirement for saving power

When the unit’s external input signal level is too low, the unit will be turned oﬀ automatically in 15 minutes. Please increase the volume level of your external device.