PUTY Q20/ PT26 Portable Label Printer User Guide

Portable Label Printer Q20/PT26 User’s Guide

What’s in the box

How to use it

Attention
To keep the best performance of the battery, please fully charge it before using it.

Attention
The installation of the label and charging battery are preparations before using the printer.

Charging battery
Insert TYPE-C 5-2A
Please purchase and use the adapter with certification that meets the charging standard if you want to charge with it

Attention
Charging: The indicator flashes
Fully charged: The indicator stops flashing and shows
Version without display: Red LED light wilt stop flashing and going out

please use the adapter with certifications

Installation of label

The size of the label for 020/9126 is 52mm( max diameter), 20-52mm( width) please make sure that the printing surface faces down as shown in the figure below when installing the label.

Attention

• please make sure be 0only PUTY labels with this machine
• please make reset the label duster in the correct position
• Lock the cower after installation of the label

Exterior description

PT26 display description

• Wireless communication
  The sign will show after Bluetooth connected successfully

• Out of label
  The sign indicates the status of out of the label. The sign will show the situation of out of label or wrong installation of Label.

• External power supply indicator
  The sign will show the external power supply inserted.
  

• Battery level
  The sign flashes while charging. Please charge at the low battery in time
  

• Text area
  This area shows some text information.

Basic functions

• Turn on
  Press and hold the power button for 3 seconds to turn on the printer

• Power off
  Press and hold the power button for 3 seconds to turn off the printer.

• Feed label
  Press the feeding button to set the label in the proper position.

• Auto power off
  The printer wilt be turned off automatically after a standby period

Setting PT26 initial settings

The user’s setting interface will show when the printer turns on.

Setting Q20 initial settings

• Charging. “Red light” is on
• Fully charged; “Redlight” is off automatically.
• Failure mode. “Red tight” flashes: (Low battery) (Label stuck (Label out)
• Connecting mode. “Blue light” is on.
• Operation mode: “Blue light” flashes.
• Power-on mode: “purple light” is on.
• Upgrade mode; “Red light” and “Blue light” flash alternately.
• Timing mode: The printer will be turned off automatically after 5min(without connection or operation) or 10min(without data transfer)
• Self-test: Press and hold to print out the self-test page
• Calibrate label: Double press to calibrate label automatically.

Connection mode

Bluetooth connection
NFC transmission connection( Non-touch identification_and interlinked technology)

• Approaching to ( e of the pinter to connect via a smartphone mapped with function.
• The app will prepare all the work before prioting automatically(it will pop up the AP for downloading at the first tire)

APP Printing

1. Download the App; Scan the OR code to download the App pr use the smartphone equipped with NFC function to open its APP automatically when approaching to the NFC area of the printer
   http://c3.cli.im/FzDh3n

2. . Download the PC software: Please download the PC software via http://www.szpushi.com/en

http://www.szpushi.com/en|
---|---

Maintenance and repair

Maintenance instruction

1. while dusting the outside and paper compartment of the printer: Please wring out the wet cloth and wipe them gently.

2. white leaning the print head: Please lean it occasionally which will help keep foreign matter from getting inside the printer.
   You can easily clean it using the following methods
   

3. If the printer gets soaked in water, please turn it off and remove the battery soon, leaving it in the open air.3. If the printer gets soaked in water, please turn it off and remove the battery soon, leaving it in the open air.

4. If the printer won’t be used for a long time, please remove the battery and store it separately

Usage and storage of printer consumables

1. The unopened products should be stored at room temperature.
2. Please clean the surface of the posted item, when sticking the printer consumables.

When you hear the sound ” DI” two times during a
short break.| The battery may be weak.| Please charge it in time.
When the printer prints without data.| Install the wrong side.| Please insert it correctly.
The print quality is faint.| The printer has not been cleaned for a long time and the print head was polluted.| Please clean the print head.
Poor printer consumables.| Please try to adjust the print density and the print quality. Please use PUT original consumables.
When you hear the sound DING three times.| The print head is not locked tightly when printing.| Please lock the print head tightly.
The labels become faint even for a few weeks.| Poor quality consumables.| Please use the original high-quality labels and ribbons.
The power turns off when you try to print.| The battery has run out.| Please charge it soon.

Note: Do not use poor quality labels, otherwise it may cause damages to the print head.

Printino

Printing method| Thermal printing
Output mode| Black and white
Printing resolution| 203dpi
Max with| 52mm
Max diameter| 52mm
printing speed| 30mm/s
Standby time| 180 days
Communication mode| Us8/Bluetooth/NFC
Positioning mode| Reflective
Printing instruction| ESC/POS/PUTY
Printing content| Text/ mage/ Line( PG, BMP, TI, JPEG and other types are available)
Barcode printing| 10/ 20 8arcode
Connection mode| PC us8, Bluetooth (Android 10S)
Printe
weight| 220g (With battery)
Size| 121mm82mm60mm
Operating environment| Temperature 040, Humidity 5%10% (RH)
without condensation
Battery
Type| Lithium polymer battery
Voltage| 74V
Electricity| 1200mAh
Consumables
Type| Continuous/ Die-cut/ Black mark
form| Max 52mm52mm( with diameter)
Specification| Roll
Thickness| 0.05mm -0.25mm

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user  is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Other precautions

Label printer installation and handling

• Avoid pressing backward when the paper cover is opened to the maximum position.
• Install the label roll in the correct way and pass through the paper guide slot
• Make sure the print head is in the locked status before feeding and printing
• The printer head is a precise and vulnerable part. Please avoid touching by hands or hard objects directly.
• Please use the dedicated power adapter.

Cautions of printing head:

• Be sure to turn off the printer before cleaning.
• Since the printing head temperature will become high during printing if you want to clean the printing head, turn off the printer for 2 to 3 minutes before starting cleaning.
• Do not touch the heating section of the printing head when cleaning it.
• Note that the print head can not be scratched or damaged.

3C certification standards:

• 3C certification is China’s mandatory product certification system, the English name is China Compulsory Certification, abbreviation CCC, so-called “3C” certification, it is a product conformity assessment system implemented in accordance with the laws and regulations that Chinese government protect the consumer personal safety and national security, to strengthen product quality management.
• This label printer and power adapter have been certified by the People’s Republic of China CCC.
• This installation guide is designed to help users use and maintain the label machine, mentioned product or company name may be a trademark or registered trademark of another company, only for its own interpretation of the use, not involve infringement. Any companies or individuals cannot use, copy or reprint any information in this manual unless it is authorized by the manufacturer.

Battery recycling:

• This product uses a rechargeable lithium battery. In order to protect the environment, please do not arbitrarily deal with used batteries.
• Be sure to dispose of used batteries in accordance with the relevant regulations.

Warranty Card

Esteemed customer thanks for purchasing our label printer.
You can apply for free warranty service by warranty card. Please retain this warranty card as proof of guarantee

Warranty Policy

• Please present your warranty card and proof of purchase when applying for the warranty service.
• Maintenance only for products within the guarantee period and warranty coverage.
• Warranty service does not belong to the scope of maintenance services spare parts and maintenance fees will be charged according to the standard,
• Products must be with considerable protective packaging to avoid product damage in transportation when sent back to repair. If not, more additional maintenance costs will be charged.
• Warranty service offered to the corresponding products in accordance with the terms and conditions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>