GODIGITALLOCK Hafele ER5100 Digital Lock User Manual
- June 6, 2024
- GODIGITALLOCK
Table of Contents
GODIGITALLOCK Hafele ER5100 Digital Lock User Manual
- The contents of this user manual are subject to change without prior notice to the user in order to enhance performance of the products.
Warnings
- Read and understand all instructions before you use your product.
- If damage is caused by failure to follow instructions, the warranty does not apply.
- Only use the alkaline batteries.
- Do not expose the product and accessories to rain or water.
- Do not expose the product to corrosive substances so as not to damage the protective cover.
- Do not scrape the fingerprint sensor with sharp objects, otherwise it may cause permanent damage.
- When cleaning the product, please wipe with a soft cloth.
- If there is a low battery alert, please replace all the batteries in time and make sure they are properly installed.
Overview
Programming
- You can operate following the voice guide by multi-language(English/Spanish/Portuguese/French).
- Master PIN Code(4~10 digit): Default master PIN code is “12345678”,please modify it after installation.
- User PIN Code(4~10 digit): Maximum capacity is 20 with user number [00-19].
- Fingerprint: Maximum capacity is 100 with user number [00-99].
- Card: Maximum capacity is 100 with user number [00-99].
Definitions
Master Mode:
The Master Mode could be entered by entering “**+Master PIN Code+#” to
programming the lock.
Master PIN code:
The Master PIN Code is used for unlock, programming and setting feature. The
default Master PIN code[12345 678] is required to be changed immediately after
enter the menu for the first time.
Auto locking:
After unlocking successful by PIN Code/ Fingerprint/ Card/ APP, it will
automatically locking in auto mode once the door is closed.
Manual Mode:
Auto mode could be adjusted to Manual Mode. In Manual Mode the lock could be
locked only by pressing any key for 1 second from outside or using thumb turn
or CLOSE/OPEN button from inside.
One Touch locking:
When the bolt is retracted, activating the keypad and press any key for 1
second will extend the bolt.
Shutdown Time:
The lock will shutdown for a default of 5 mins and not allow operation after
the wrong code entry limit(10 times) has been met. When the unit is in
Shutdown, the screen will flash when you are trying to use keypad.
Away Mode:
This feature is enabled by the Master PIN Code in Master Mode , it restricts
all user PIN code/ Fingerprint/ Card, except Master PIN code and APP access.
This feature will disabled automatically after entering Master PIN Code from
outside or using APP. If someone unlock the unit by using thumb turn, the lock
will alarm for 1 min and send a message to user＇s hand-held device for
warning(requires wireless module).
Silent Mode:
Enabling Silent Mode shuts off the code confirmation tone playback for use in
quiet areas. Silent mode is selected in the voice setting of Master Mode.
Status LED:
Located on outside panel.
Wrong Code Entry Limit:
After a specified number of unsuccessful attempts at entering a valid PIN code
the lock will shut down and not allow operation. Wrong code entry limit is 10
times.
Reboot button:
When the system crash down, the lock could be restart by pressing Reboot
button on outside panel.
Reset button:
After reset operation, the lock will be restored to factory default settings,
all user credentials will be deleted.
Refer to reset guide.
Privacy mode:
After holding the CLOSE/OPEN button for 3 seconds, the lock will be set to
Privacy mode, it restricts all user PIN code/ Fingerprint/ Card, except Master
PIN code and APP. This feature will disabled automatically after entering
Master PIN Code or using APP access from outside, or someone unlock the unit
by using thumb turn.
Factory Default Settings
Quick setup guide
Lock Operation
-Change Master PIN code
1.Before changing default Master PIN code, all other setting menu will be disabled. You have to change Master PIN code first, then do other lock settings.
-Add Up User PIN Codes
User PIN codes can be programmed through the Master PIN Code.
1.When registering User PIN Codes, the code must be entered within 10 seconds
or time expires.
2.No matter setting succeed or failed, the process won’t completed and stay at
current stage, you can press “*” to return to previously menu.
-Add Up User Fingerprint （Only available on ER5100）
User fingerprint can be programmed through the Master PIN Code.
1.When registering user fingerprint, the fingerprint must be entered within 10
seconds or time expires.
2.No matter setting succeed or failed, the process won’t completed and stay at
current stage, you can press “*” to return to previously menu.
-Add Up User Card
User card can be programmed through the Master PIN Code
1.When registering user card, the card must be entered within 10 seconds or
time expires.
2.No matter setting succeed or failed, the process won’t completed and stay at
current stage, you can press “*” to return to previously menu.
-Delete User PIN Code
User PIN codes can be programmed through the Master PIN Code.
1.When deleting User PIN Codes, the User Number must be entered within 10
seconds or time expires.
2.No matter setting succeed or failed, the process won’t completed and stay at
current stage, you can press “*” to return to previously menu.
3.Deleting all User PIN codes could be done only by resetting the lock to
factory default settings.
-Delete User Fingerprint （Only available on ER5100）
User fingerprint can be programmed through the Master PIN Code.
1.When deleting User fingerprint, the fingerprint must be entered within 10
seconds or time expires.
2.No matter setting succeed or failed, the process won’t completed and stay at
current stage, you can press “*” to return to previously menu.
3.Deleting all User fingerprint could be done only by resetting the lock to
factory default settings.
-Delete User Card
User card can be programmed through the Master PIN Code.
1. When deleting User card, the card must be entered within 10 seconds or
time expires.
2. No matter setting succeed or failed, the process won’t completed and stay
at current stage, you can press “*” to return to previously menu.
3. Deleting all User card could be done only by resetting the lock to factory
default settings.
-Locking Mode
The default locking mode is auto mode.
-Language Settings (including silent mode)
Silent Mode feature can only be programmed in language settings through the Master PIN Code.
-Enable Away Mode
Away Mode feature can only be programmed through the Master PIN Code.
1. In Away Mode, all User PIN Code/fingerprint/card will be disabled
temporary, device could be unlocked only by Master PIN code or APP.
2. Away Mode will be disabled automatically after entering Master PIN Code or
using APP access.
3. If someone unlock the device by using thumb turn or override key, the
alarm voice will be triggered.
-Function Extension
It is reserved for the connection of bluetooth, remote control and Z-wave.
1. For bluetooth settings, please turn on the bluetooth of smart phone and
open Kaadas APP before above operation.
2. For remote control and Z-wave settings, please refer to its instructions
separately
Menu Table
How to use
Open Door
1. Open from outdoor
2. Open from indoor
Close Door
1. Close door from outdoor
Auto Locking Mode : In auto mode, the deadbolt will come out automatically after unlock.
Manual Locking Mode:
Enable Privacy Mode
When the door is closed, long press CLOSE/OPEN button for 3 seconds to enable privacy mode. In privacy mode, all user PIN code /fingerprint /card will be prohibited, except Master PIN code and APP key. And if the device is unlocked from indoor , the alarm will be triggered until PIN code /fingerprint /card is verified successfully
Fake PIN code
The random numbers can be added before and after the real PIN code, this prevents the user PIN code from being exposed. The maximum length is 32 digits.
Micro USB emergency power supply and Reboot button
– When the battery voltage is too low to open the lock from outside, you can
use 5V power bank to charge the door lock via Micro USB port. After the door
is unlocked, please replace all batteries immediately.
– Pressing reboot button to restart the smart lock when system is crash down.
Reset to factory default settings
Operation Instructions:
- Keep the lock in “unlock” status
- Open battery cover and find the reset button.
- Use a sharp thing to press and hold the reset button.
- Remove at least 1 pcs battery from battery box, then reinstall all batteries to charge again.
- Keep holding the reset button until hearing voice guide.