Roccat SYN PRO AIR User Manual and Driver

: June 6, 2024
: ROCCAT

Table of Contents

PACKAGE CONTAINS
HEADSET CONTROLS
LED INDICATIONS
CHARGING
PC SETUP
TECHNICAL FACTS
MICROPHONE ATTACHMENT
MICROPHONE FLIP-TO-MUTE OPERATION
Operating systems:
Download
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

SYN PRO AIR Headset

QUICK START GUIDE

Download Driver

PACKAGE CONTAINS

HEADSET CONTROLS

LED INDICATIONS

Connection Status LED

Solid White = Headset Connected Double Blink White = Headset Pairing Pulsing White = Headset On / Full Battery Solid Red = Headset Charging Pulsing Red = Low Battery LED OFF* = Headset Off

Connection Status LED

Solid White = Headset Connected Double Blink White = Headset Pairing Pulsing Red = Microphone Muted

CHARGING

The Syn uses a 24+ hour rechargeable battery. Make sure to charge it regularly.

Headset Storage
Always charge your headset before storing it for any extended period of time (greater than 3 months). Never store the unit in temperatures above 113°F/45°C

PC SETUP

Plug the Syn Transmitter in a USB slot on your PC
Hold the Power Button for 2 seconds to turn on the headset (the transmitter and headset are automatically paired)
Right click the speaker icon in your toolbar and select “Open Sound Settings”
Select “Syn” from the “Choose Your Output Device” drop-down menu
Open the driver software to customize your settings

Keep your ROCCAT® product up to date with the latest software and firmware

TECHNICAL FACTS

TECH SPECS

Direct wireless connection via USB-A transmitter
20Hz – 20kHz speaker frequency response
2.4GHz transmitter frequency response
Audio controls: power button, master volume wheel, mic mute, mic monitor wheel
Rechargeable 24h battery (average 1+ week play time based on typical ~3h use per day)
50mm speakers with neodymium magnets
Removable unidirectional microphone
Athletic fabric headband with foam cushioning
Over-ear design featuring memory foam

SYSTEM REQUIREMENTS

Windows® 10 (software support)
USB 2.0 (or higher)
Internet connection (for driver software)

Should you need assistance …
Our support team is ready to help you with any technical questions. Just send an e-mail to support@roccat.com or visit our website at: WWW.ROCCAT.COM/SUPPORT

MICROPHONE ATTACHMENT

Remove the Microphone Cover from the left ear cup.
Align the Removable Microphone with the microphone slot on the left ear cup.
Press firmly until the Removable Microphone clicks into the microphone slot.

MICROPHONE FLIP-TO-MUTE OPERATION

Microphone Mute
Flip up mic to mute. There is an audbile tone when the mic is muted or unmuted.

Mic Unmuted
Mic Muted
Mic Muted

REGULATORY COMPLIANCE STATEMENTS FOR THE SYN PRO AIR RX & TX

LOCAL RESTRICTIONS ON RADIO USAGE
Caution: Due to the fact that the frequencies used by wireless devices may not yet be harmonized in all countries, these radio products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.

To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer‘s OEM Regulatory Guidance document at the following URL http://www.turtlebeach.com/homologation or contact Turtle Beach directly

FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE NOTICES
This section includes the following FCC statements for the Syn:

FCC IDs: XGB-15150 & XGB-15153
Class B Interference Statement
RF Radiation Exposure & Hazard Warning
Non-Modification Statement

CLASS B INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF RADIATION EXPOSURE & HAZARD STATEMENT
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

NON-MODIFICATION STATEMENT
Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the Syn Pro Air RX & TX Models and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. Please contact Turtle Beach for a list of approved 2.4 GHz antennas.

This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-314 (CPSIA)

CANADIAN ICES STATEMENTS
IC: IC: 3879A-15150 and 3879A-15153

This device complies with ICES-003 and RSS-247 of Industry Canada.
Operation is subject to the following two conditions:

This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the device

To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing and not supported by Syn Pro Air RX & TX Models.

RF RADIATION EXPOSURE & HAZARD STATEMENT
To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

EUROPEAN UNION AND EUROPEAN FAIR TRADE ASSOCIATION (EFTA) REGULATORY COMPLIANCE

This equipment may be operated in the countries that comprise the member countries of the European Union and the European Fair Trade Association. These countries, listed below, are referred to as The European Community throughout this document:

AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE,, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND

Declaration of Conformity
Marking by this symbol:

indicates compliance with the Essential Requirements of the EMC Directive of the European Union (2014/30/EU). This equipment meets the following conformance standards:

Safety: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013(T-Mark License), IEC 60950-1:2005 (2nd Ed.) + Am 1:2009 + Am 2:2013 (CB Scheme Certificate), EN 62368-1: 2014 + A11 (T-Mark License), IEC 62368-1: 2014 (CB Scheme Certificate), EN 50332-1:2013, EN 50332-2:2013, EN71-3:2013
EMC: EN 55032:2015; CISPR 32:2015, EN 301489-1 V2.1.1(2017-02), EN301489-17 V3.1.1(2016-11) EN 61000-4-2: 2009, EN 61000-4-3: 2006 + A1: 2008 + A2: 2010, EN 61000-4-8: 2010
Radio: EN 300 328v2.1.2 (2019-07)
SAR: EN 62311:2008
Environmental: RoHS 2015/863 amending Annex II to 2011/65/EU, WEEE 2012/19/EU, REACH 2006/1907/EC, Packaging 94/62/EC, Battery 2006/66/EC, Toys Safety Directive 2009/48/EC

Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.

To Access the Rating Lable:

Remove the left ear pad by pulling the ear pad straight up using your thumb.
Once you’ve released the lip on top, pull the ear pad straight back and it should slip right off.

To replace the ear pad, follow the same process in reverse.

Warning!
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case, the user may be required to take appropriate measures.

Attention
This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

VOYETRA TURTLE BEACH, INC. | 44 SOUTH BROADWAY, 4TH FLOOR, WHITE PLAINS NY 10601, USA
© 2021 Voyetra Turtle Beach, Inc. All rights reserved. Any product names mentioned in this manual may be trademarks or registered trademarks and are the property of their respective owners. Information contained herein is subject to change without notice. Voyetra Turtle Beach, Inc shall not be made liable for any errors that may appear in this manual. This publication or parts of it may not be reproduced without the express consent of the publisher.

Please visit the following URL for a complete copy of the Declaration of Conformity: http://www.turtlebeach.com/homologation

Operating systems:

Windows® 10 64 Bit

Neon is the brand new driver software from ROCCAT®. It’s modern, slick and lightweight. Download Neon to take your ROCCAT® devices to the next level.

This new software is in the beta phase. We’re constantly making improvements to give you the best experience, and once you download Neon, you’ll be notified when there are new updates available.

Download

Roccat SYN PRO AIR Driver – Download Driver

Roccat SYN PRO AIR User Manual – [ syn-pro- air_en_fr.pdf ] Roccat SYN PRO AIR User Manual – [ syn-pro- air_es.pdf ] Roccat SYN PRO AIR User Manual – [ syn-pro- air_ja.pdf ] Roccat SYN PRO AIR User Manual – [ syn-pro- air_ko.pdf ] Roccat SYN PRO AIR User Manual – [ syn-pro- air_tw.pdf ]