Beghelli 26702 Sanifica Aria Instruction Manual

Installation, use, and maintenance manual

|
---|---
|
|
|

IMPORTANT
SAFETY WARNINGS

• The device contains a UV-C emission lamp.
• WARNING: DO NOT activate the UV lamp when removed from the protective casing of the appliance.
• This device must only be used for its intended use. Any other use shall be deemed as nonconforming and therefore dangerous.
• Using the device otherwise than as described herein or if the housing is damaged can result in UV-C radiation leaks.
• Even small doses of UV-C radiation can damage eyes and the skin.
• Please read the maintenance instructions before opening the device.
• The device must be turned off and disconnected from the power supply before replacing the uvOxy® Beghelli cartridge (code 26721).
• Do not insert small objects into the ventilation grid. They could damage the fans and impair the device’s operation.
• If damaged, the device should not be used.
• In case of accidental fall, check the correct ignition of the UV-C lamp by checking that the LED does not signal anomalies (the RED LED must NOT be turned on).
• In case of failure or malfunction, do not tamper with the device. Please contact only an authorized technical service center for repairs.
• The device must be used exclusively indoors and not outdoors. Any other use shall be deemed improper.
• Children mustn’t play with the device. Cleaning and maintenance must not be done by children without adult supervision.
• Make sure the device is connected to a grounded outlet.
• DO NOT obstruct the air passage grates with objects.

SanificaAria 200 TECHNICAL FEATURES (cod. 26702) Power supply: 90VAC ÷256 VAC, 50÷60Hz (2m long cable) Absorption:

• <60W (minimum speed)
• <65W (medium speed)
• <75W (maximum speed)

Standby absorption: < 1.5W
UV-C Lamp: 2 X TC 2G11 24W (total 48W)
UV-C wavelength: 254nm
Flow of treated air:
– 200m³/h at maximum speed
– 130m³/h at medium speed
– 81m³/h at minimum speed
Radiant power UV-C: 14W
Ozone-free UV-C lamp
Cartridge life: 12 months (continuous use). Replacing the cartridge allows you to keep the germicidal performance of the device in time.
Noise level:

• 38dB(A) at 1 meter (minimum speeda)
• 47dB(A) at 1 meter (medium speed)
• 59dB(A) at 1 meter (maximum speed)

Weight: 13kg (10Kg without bracket)
ON/OFF button and fan speed adjustment (3 speeds)
BLE interface for local control using the SanificaAria Beghelli APP for Android and IOS
Wi-Fi interface for remote control via DOME-E APP for Android and IOS

RADIO TECHNICAL CHARACTERISTICS
Transceiver with Bluetooth® Low Energy (BLE) wireless technology
Frequency band: 2,4GHz-2,4835GHz
Power RF: <100mW e.i.r.p.
Transceiver WiFi
Frequency band: 2.400-2.4835GHz
Wi-Fi standard: IEEE 802.11b/g/n (channels 1-14)
Power RF: <100mW e.i.r.p.

Beghelli S.p.A. declares that the radio transceiver devices compliy with European Directive 2014/53/UE.
The full text of the EU Declaration of Conformity of the device is available at:
www.beghelli.it >area tecnica>download
www.beghelli.it/it/area-tecnica/strumenti/download
The devices can be used in a ‘free use’ policy.

MAINTENANCE
Before cleaning or maintenance, make sure the device is turned off and disconnected from the power supply.

CLEANING
Periodically remove the dust, eventually deposited on the external grids, using a brush. When replacing the Cartridge, remove the dust on the internal deflectors.
Note: The residual dust agglomerates in the sanitizing chamber are totally free of bacterial load.

DISPOSAL
The packaging is made out of recyclable materials. Dispose of it according to environmental protection regulations, by separate collection.
According to European Directive 2012/19/EU, the device fallen into disuse must be disposed of in a compliant manner: It must not be discarded as unselected municipal waste. It must be taken to recycling centers or sent back to the Beghelli vendor.
Recyclable materials used in the appliance can be recovered to avoid environmental pollution.
For more information, please contact your local disposal authority or the appliance vendor.

A. INSTALLATION WITH FLOOR SUPPORT

• Connect the power cable to the mains

B. WALL INSTALLATION WITH CABLE POWER

• Remove the support bracket
• Open the door of the device
• Unscrew the 2 safety screws
• Slide the cover upwards to remove it from the catch, then pull it out
• Unscrew the safety screws and remove the cartridges
• Remove the aesthetic covers and the relative fixing nuts (8mm wrench)
• Using the template supplied, make 4 holes in the wall (screws and wall plugs not supplied; Ø 6mm wall plugs and Ø 4.5mm cross screws  recommended)
• Pre-assemble the screws leaving them out of the wall by at least 5mm
• Hang the device through the slots on the bottom then tighten the screws
• Connect the power cable to the mains
• Replace the cartridges, the cover and close the device

B1. WALL INSTALLATION WITH POWER SUPPLY FROM DUCT

• Unscrew the screws and remove the circuit cover
• Carry out the wiring as indicated
• Replace the cartridges, the cover and close the device

C. OPERATION AND ADJUSTMENT

LED SIGNALS:

• WHITE: DEVICE IN STANDBY, SANITIZATION OFF
• LIGHT BLUE: regular operation, SANITIZATION ON
• BLUE: regular operation with Bluetooth® (BLUE LED with sanitizer connected to the SanificaAria App)
• RED: operating anomaly (check the type of anomaly with the SanificaAria App or DOM-E):
• “uvOxy cartridge exhausted” (replace the cartridge)
• “blown fan” (the device must be repaired by the technical assistance service)

Note: The device contains two uvOxy cartridges. In case of exhaustion of only one of the two cartridges, the sanitizer continues to operate with reduced performance, until the other cartridge runs out. Replace both cartridges as soon as possible.

ON / OFF BUTTON:
On / off and manual adjustment of the fan speed.

• FIRST PRESS: Speed 1 (1 beep)
• SECOND PRESS: Speed 2 (2 beeps)
• THIRD PRESS: Speed 3 (3 beeps)
• FOURTH PRESS: STAND-BY (long beep)

N.B. The device turns on at speed 2.
After a power cut, the device ALWAYS turns on at minimum speed.
The device can be controlled via Bluetooth® locally with the SanificaAria App and, at the same time, it can also be controlled remotely via WiFi with the DOM-E Beghelli App.

USING THE APP SanificaAria Beghelli:
The device can be switched on / off and the fan speed and the on / off timer can be adjusted via the Beghelli SanificaAria App.
The smartphone connects to the device via Bluetooth®:

• download the SanificaAria Beghelli App (available on the App Store and Google Play) and activate  it (no need to register, the App works like a simple remote control);
• approach the device, within a range of about 2 meters; as soon as the sanitizer recognizes the presence of the smartphone, the App menu is activated, the sanitizer LED turns BLUE and the remote control is functional. The Bluetooth® connection remains active as long as the App is in the foreground on the smartphone; afterward, the sanitizer LED turns white.

In the event of a power failure, the device loses the information set through the App, including any timer configuration. The App signals the exhaustion of the cartridge with a specific ICON.

USING THE APP DOM-E Beghelli:

The device can be controlled (on / off) and adjusted remotely (3 fan speeds and on/off timer) via the DOM – E Beghelli App. For this use, the sanitizer must be connected to a 2.4GHz WiFi:

• download the DOM-E Beghelli App (available on the App Store and Google Play) and activate it;
• add the new SanificaAria 200 device to the App using the “+” icon
• follow the instructions on the App for connecting and configuring the WiFi connection
• when requested by the App, press the ON / OFF button of the device for at least 6 seconds; a rapid sequence of “beeps” and the flashing of the LED highlights the con­nection phase in progress. At the end of the process, after about 2 minutes, the LED signals normal operation or any anomaly. If necessary, repeat the connection / confi­

In the event of a power failure, any timer configurations set through the DOM-E App are kept by the cloud system and do not need to be reset.
Note: The timer set with the SanificaAria App and the DOM-E App do not synchronize with each other. It is recommended to use only one of the two timer modes to avoid confusion.

D. uvOxy® 200 SANITIZING CARTRIDGE REPLACEMENT
For the correct operation of SanificaAria, the Sanitization Cartridge must be replaced every 12 months of operation, and in any case when the device signals this. To maintain the effectiveness of sanitation, as well as ensure the total absence of ozone emissions harmful to people’s health, use only original uvOxy® Beghelli cartridges, also available online (www.beghelli.it/store)

The failure of one of the two uvOxy® cartridges is immediately notified by turning on the RED LED, sending a message to the DOM-E App, and lighting up an icon on the Air Sanitizer App. In the event of a single cartridge failure, the sanitizer continues to operate with reduced effectiveness. When both cartridges are faulty, in addition to the previous notifications, the sanitizer switches off the fan and activates a continuous periodic acoustic signal: 3 beeps every 30 minutes.
Both cartridges must ALWAYS be replaced even if the reported fault is related to the single cartridge.
Before proceeding with the cartridge replacement, disconnect the device from the power supply

• Open the door of the device
• Unscrew the 2 safety screws
• Slide the cover to remove it from the catch, then pull it out
• Unscrew the safety screws and replace the cartridges only with original uvOxy® Beghelli spare parts (code 26721)
• Put the cover back on, tighten the two screws and close the device door

BEGHELLI S.p.A. – Via Mozzeghine 13/15 – loc. Monteveglio 40053 Valsamoggia (BO) – ITALY
Tel. +39 051 9660411 – Fax +39 051 9660444

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>