global sources SY-W0241 Alarm Clock Night Light Wireless Charger User Manual

: June 6, 2024
: global sources

Table of Contents

Function
Specification
Applicable Equipment
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Manual of Alarm Clock Night Light Wireless Charger
Model: SY-W0241

Function

A. Power Connection

Plug the USB-A end of the cable into the power adapter while plugging the Type-C end into the product.
The product will be ready and stand by after all indicators are on.

B. Wireless Charging

Output: 10w
Indicator display:
Power connection successful – blue light flashes twice
Standby – light off
Charging – blue light on
Charged – light off
FOD – blue light flashes continuously

C. Alarm Clock Function

Buttons: M, +, -, night light button.
Time System Setting:
Double click the M button to set up a 12-hour time system and a 24-hour time system. AM and PM will display while A 12-hour time system is set.
Time Setting:
1) Click M button once to enter the minute setting, adjust the value with +/-.
2) Click M button once after the minute setting, to enter the hour setting, adjust the value with +/-.
3) Click M button a third time to finish the time setting.
Alarm Setting:
1) Press “+” 3 seconds to activate Alarm; Press “-” 3 seconds to deactivate Alarm. The alarm indicator is on while the Alarm is activated.
2) While activated, press M button for 3 seconds to enter the alarm minute setting, adjust the value with +/-.
3) Click M button once after the alarm minute setting, to enter the alarm hour setting, adjust the value with +/-.
4) Click M button a third time to finish the alarm time setting.
5) Alarm bell rings for 3 minutes until automatic off while no operation.
6) Tap the product to enter Sleepy Mode when the bell rings. Bell rings two more times after 5 minutes. The indicator flashes and the M button is out of function during the Sleepy Mode. If time setting is needed, please long press “-” to stop the alarm. All buttons will function normally.
7) Time display brightness can also be adjusted manually to 4 grades. “+” and “-” can be used to adjust display brightness manually. The default grade is maxed brightness when power is connected. Single click “-” too dark the display one grade. The display brightness goes dark for the last grade and goes bright automatically at 7 am the next day. All manual adjustments will be synchronized to automatic adjustment.
8) If do not need an alarm clock, click any button of the products to stop the bell and close the alarm clock.
Night Light Setting:
1) Night light brightness can be adjusted by 3 grades.
2) Click the round button on the left side of the product to turn on the night light. The default brightness grade is mini brightness.
3) Click again to get mid brightness. Click a third time to get max brightness.
4) Click the round button a fourth time to turn the night light off.
Eco-power function:
1) Button cell inside is only for timekeeping.
2) All functions are out during power disconnection. Functions are restored when power is connected.

D. Note

Attention: In order to function alarm, wireless charging, night light and USB output all together, power shall be connected by a QC2.0 or QC3.0 adapters. If connected by a 5V adapter, only wireless charging and alarm can work together.
Do not squeeze or collide.
Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
Do not place too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
Keep children from the product in case they play the wireless charger as a toy to avoid accidents.
Keep the wireless charger and receiver device away from water and other liquids.
To clean the charger, make sure the power supply is disconnected.
Usage temperature: 0-45℃.
Usage humidity: 20-85% (40℃)

Pictures in this manual are all illustrations. The final product is subject to fact.
Inside package: alarm charger, charging cable, manual.
Power adapter is not included. Please purchase otherwise or use the phone’s original adapter.