PORTLAND 56808 9.5 In. 7 Amp Corded Electric Pole Saw Owner’s Manual

ELECTRIC
1.5 PEAK HP
POLE SAW
Owner’s Manual & Safety Instructions
Visit our website at:http://www.harborfreight.com
Email our technical support at:productsupport@harborfreight.com

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance, and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if the product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.|
Copyright© 2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, the actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

WARNING SYMBOLS AND DEFINITION

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
---|---
| Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
| Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
| Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
| Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

When using electric gardening appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury,  including the following:

READ ALL INSTRUCTION

Power cord Safety

WARNING! – to reduce the risk of electric shock, use only with an extension cord intended for outdoor use, such as an extension cord of cord type SW-A, SOW-A, STW- A, StOW-a, SJW-A, SJOW-A, SJtW-A., or SJtOW-A.

1. Extension cord – Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating.

2. Ground Fault circuit interrupter (gfci) protection should be provided on the circuit(s) or outlet(s) to be used for the gardening appliance. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.

3. Do not abuse cord – Do not carry the appliance by a cord or yank it to disconnect from receptacle.
   Keep cord from heat, oil, and sharp edges.

4. to reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit,  obtain a correct polarized extension cord.

5. a polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. This design is referred to as double-insulated, indicated by .

Extension cord Size
The following table shows the correct cord size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

TABLE A- MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT)

Ampere Rating (at full load)|

EXTENSION CORD LENGTH

25′| 50′| 100′| 150′
0 – 6| 18| 16| 16| 14
6 – 10| 18| 16| 14| 12
10 – 12| 16| 16| 14| 12
12 – 16| 14| 12| Not recommended

Connecting cords
To reduce the risk of the cords pulling apart during operation, do one of the following:
a. Make a knot as shown below then connect the cords:

b. Or, use a plug- receptacle retaining
Strap or connector designed to hold extension cords to appliance cords.

Personal Safety

1. Dress properly – Do not wear loose clothing or jewelry. They can be caught in moving parts.
   Use of rubber gloves and substantial footwear is recommended when working outdoors.
   Wear protective hair covering to contain long hair.

2. Wear ANSI-approved safety goggles, a hard hat, and heavy-duty rubber work gloves. Use a face or dust mask if the operation is dusty.

3. Avoid Unintentional Starting –
   Do not carry plugged-in appliances with a finger on the switch. Be sure the switch is off when plugging in.

4. Do not Overreach –
   Keep proper footing and balance at all times.

5. Stay alert – Watch what you are doing. Use common sense. Do not operate appliances when you are tired.

6. DANGER! people with pacemakers should not use pole saws. Pole saws produce strong electromagnetic fields that can cause pacemaker interference or pacemaker failure. People with pacemakers should consult their physician(s) for advice.

Gardening appliance Use and care

1. Avoid Dangerous Environment –
   Do not use appliances in damp or wet locations.

2. Do not use it in rain.

3. Keep children away – All visitors should be kept at a distance from the work area.

4. When servicing use only identical replacement parts.

5. Use the right appliance – Do not use the appliance for any job except that for which it is intended.

6. Do not Force appliance – It will do the job better and with less likelihood of injury at the rate for which it was designed.

7. Store idle appliances indoors – When not in use, appliances should be stored indoors in dry, and high or locked-up places – out of reach of children.

8. Disconnect appliance – Disconnect the appliance from the power supply when not in use, before servicing, when changing accessories such as blades, and the like.

9. Check Damaged parts – Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by a qualified technician unless indicated elsewhere in this manual.

10. Carefully follow the cutting procedures explained in this manual. They are specifically planned to reduce risk to the operator.

11. lock the pole in place securely before using pole Saw.

12. Maintain appliance With care – Keep the cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace them if damaged. Keep handles dry, clean, and free from oil and grease.

Vibration Hazard

This appliance vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms, and  shoulders. To reduce the risk of vibration-related injury:

1. anyone using vibrating appliances regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this appliance. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the vibration effects on the user.

4. Use appliances with the lowest vibration when there is a choice between different processes.

5. include vibration-free periods each day of work.

6. Grip appliance as lightly as possible (while still keeping safe control of it).
   Let the appliance do the work.

7. to reduce vibration, maintain the appliance as explained in this manual. If any abnormal vibration occurs, stop use immediately.

General Safety

1. Stop working when you feel tired or exhausted. Make regular breaks to rest.

2. Keep all parts of the body away from the saw chain.
   Do not remove cut material or hold material to be cut when the saw chain is moving. Make sure the switch is off when clearing jammed material.

3. Hold pole Saw by insulated gripping surfaces only, because the saw chain may contact hidden wiring or its own cord. Saw chains contacting a “live” wire may make exposed metal parts of the garden power tool “live” and could give the operator an electric shock.

4. Keep the power cord away from the cutting area.
   During operation, the power cord may be hidden in shrubs and can be accidentally cut by the blade.

5. before use, make sure the saw chain is not contacting anything.

6. Hold pole Saw with both hands on the handle.

7. Do not operate pole Saw from within a tree.
   Operation of a tool while up in a tree may result in personal injury.

8. Keep proper footing and operate the garden power tool only when standing on a fixed, secure, and level surface. Slippery or unstable surfaces such as ladders may cause a loss of balance or control of the garden power tool.

9. When cutting a limb that is under tension, be alert for spring back. When the tension in the wood fibers is released, the limb may strike the operator and/or throw the tool out of control.

10. Do not use for bore cutting, felling or bucking.

11. Keep bystanders and other workers at least 50 feet from the work area.

12. Do not operate within 50 feet of electrical lines.

13. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped around.

14. carry pole Saw with tool switched off and away from your body. Proper handling of the Pole Saw will reduce the likelihood of accidental contact with the moving saw chain.

15. Follow instructions for lubricating, chain tensioning, and changing accessories. The improperly tensioned or lubricated chain may either break or increase the chance of kickback.

16. Kickback is the result of tool misuse and/or incorrect operating procedures or conditions. Kickback may occur when the nose or tip of the guide bar touches an object,  or when the wood closes in and pinches the saw chain in the cut. Kickback can be avoided by taking proper precautions as given below:
    a. Maintain a firm grip, with thumbs and fingers encircling the Pole Saw handles, with both hands on the saw, and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the garden power tool.
    b. Do not overreach. This helps prevent unintended tip contact and enables better control of the garden power tool in unexpected situations.
    c. Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback.
    d. Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.

17. Keep handles dry, clean, and free from oil and grease.

18. Use for cutting wood only. Do not use for cutting plastic, masonry or non-wood building materials.

19. Do not touch the guide bar tip to any object.
    Tip contact may cause the guide bar to move suddenly upward and backward.

20. Maintain labels and nameplates on the appliance.
    These carry important safety information.
    If unreadable or missing, contact
    Harbor Freight Tools for a replacement.

21. the warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product but must be supplied by the operator.

SAVE THIS INSTRUCTION

Specifications

Gauge: 0.050″
Pitch: 3/8″
Lubrication: Bar and chain oil (sold separately) If not available, SAE 30W motor oil may be used

Setup – before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 14.

Functions

Assembly instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch “OFF” and unplug the Air Compressor from its electrical outlet before assembling or making any adjustments.
Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Install Guide bar and Saw chain

CAUTION! Wear heavy-duty work gloves when handling Saw chain.

1. BEFORE FIRST USE: Soak Saw Chain in the bar and chain oil (sold separately) overnight.

2. Remove Drive Cover Hex Bolt using Hex Wrench end of the included tool, then remove Drive Cover.
   

3. Loosen Tensioning Screw using Screwdriver end of tool.
   

4. Slide Saw Chain’s drive links into Guide Bar’s groove, making sure the chain is installed in the correct rotation direction.
   

5. Place Saw Chain around Drive Sprocket, place Guide Bar’s lower oil hole over Tension Pin.
   

6. Tighten Tensioning Screw until bottoms of cutters contact bottom of Guide Bar, then tighten an additional 1/4 turn.

7. Replace Drive Cover, then tighten Drive Cover Hex Bolt.
   

8. Tension Saw Chain according to tension Saw chain on page 8.

Tension Saw chain

CAUTION! Wear heavy-duty work gloves when handling Saw chain.
NOTICE: to prevent damage to the Saw chain, do not tension the hot chain. let chain cool before tensioning.

Check tension:
a. Before every use.
b. Often during the first half-hour of use.
c. Periodically during use.

1. Snap Test: Pull Saw Chain away from the bottom of Guide Bar, then let go. Saw Chain should snap back to its original position, solidly contacting the bottom of the Guide Bar.
2. Pull Saw Chain by hand around Guide Bar several times, it should feel snug and move freely around Guide Bar.
3. Adjust tension as necessary by tightening or loosening Tensioning Screw, then repeating steps 1. and 2., until proper tension is achieved.

Fill automatic Oiler reservoir

NOTICE: to prevent damage to Saw chain, Drive bar, and Drive Sprocket, keep Oil reservoir full. Do not operate pole Saw without oil. Do not put used oil in the reservoir.
Note: Oil is automatically applied to the Saw Chain during operation.

Fill Oiler Reservoir:
a. Before every use.
b. When oil level reaches MIN mark on Oil Level Gauge.

1. Remove Oil Fill Cap.
2. Using a funnel, fill the tank with bar and chain oil (sold separately).
3. Use a clean cloth to remove excess oil.
4. Replace Oil Fill Cap and tighten.

Adjust pole Saw length

Loosen Extension Collar, extend the pole to the desired length, then tighten Extension Collar securely.

WARNING! to prevent serious injury, check the Extension collar for tightness periodically during use.

Operating instructions

Read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

• Before operating the gardening appliance, put on ANSI-approved safety goggles, hard hat and other safety gear. Safety goggles and other safety gear are sold separately.
• If an extension cord is used, ensure that it is an outdoor type extension cord and that it is the correct design to accept this appliance’s plug.

WARNING! TO PREVENT ELECTRIC SHOCK AND SERIOUS PERSONAL INJURY: The extension cord must remain secured to the appliance’s plug. Secure the extension cord by either using the knot method explained in the safety warning section, or by using a device designed specifically for retaining the extension cord.

Workpiece and Work area Set Up

1. Designate a work area that is clean and well lit. The work area must not allow access by children or pets to prevent distraction and injury.

2. Route the extension cord along a safe route to reach the work area without creating a tripping hazard or exposing the extension cord to possible damage. The extension cord must reach the work area with enough extra length to allow free movement while working. Position the cord so that it will not be caught on branches and the like during cutting.

3. Secure the extension cord by passing it through Cord Clip Access Hole, then looping the cord over Cord Clip, so there will be no tension on the connection between the Power  Cord and the extension cord.
   

4. There must not be objects, such as utility lines, nearby that will present a hazard while working.

Operation

TO PREVENT SERIOUS INJURY AND DEATH:

• Wear ANSI-approved safety goggles, a hard hat,s, and steel-toed boots during use.
• Avoid kickback. Do not touch the Guide bar tip to any object. Tip contact may cause the guide bar to move suddenly upward and backward.
• Do not operate pole Saw with one hand. Only hold Pole Saw with both hands. Do not stand directly under the branch being cut.
• Only stand on a fixed, secure, and level surface. Do not stand on a ladder or other support.
• Do not operate within 50 feet of electrical lines.

BEFORE EVERY USE:

a. Check the oil level, add oil as necessary ( see Fill automatic Oiler reservoir on page 8 ).
b. Run Pole Saw at half throttle for several minutes.
c. Stop motor and unplug pole Saw. let chain cool, then check tension and adjust as necessary ( see tension Saw chain on page 8 ).
d. Make sure Saw Chain is sharp.

DURING EVERY USE:

a. Check tension often during the first half-hour of use and periodically during use. Adjust tension as necessary (see tension Saw chain on page 8).
b. Check oil level every 10 minutes of use. Fill oil reservoir when oil level reaches MIN mark on Oil Level Gauge (see Fill automatic Oiler reservoir on page 8).

1. Connect the extension cord to 120VAC outlet.

2. To start, push and hold Trigger Safety Lock, then squeeze and hold Trigger.
   Release Trigger Safety Lock.
   To stop, release Trigger.
   

3. Make sure Automatic Oiler is distributing oil.

4. Maintain a firm grip, with thumbs and fingers encircling the Pole Saw’s handles, with both hands on the saw, and position your body and arm to allow you to resist kickback forces.
   

5. Hold the Pole Saw to the side of your body at a maximum of 60° from horizontal. Do not overreach.
   

6. Make sure Saw is running at full speed before starting a cut.

7. Cut lower branches first.

8. Do not force Pole Saw, let Pole Saw do the work.

9. Remove the Pole Saw from a cut while it is running.
   WARNING! to prevent serious injury, if the branch starts to fall, causing the saw to bind, leave the saw and get away from where the saw and branch are likely to fall immediately.
   Cutting long branches
   a. Make first cut 4″ to 6″ from the end of the branch.
   b. Make next cuts 4″ to 6″ from the previous cuts, working toward the trunk.
   Cutting thick branches:
   c. Make first cut 6″ away from the trunk, on the underside, 1/3 way into the branch.
   d. Make the second cut 2″ away. Sever branch from the top.
   e. Make third cut close to the trunk, on the underside, 1/3 way into the branch.
   f. Make the fourth cut from the top, severing branch.
   

10. When finished, release Trigger and unplug from outlet.

11. Clean, then store according to cleaning, Maintenance, and lubrication on page 12.

Maintenance and Servicing

procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK: Release the Trigger and unplug the appliance from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.

Cleaning, Maintenance and lubrication

1. BEFORE EACH USE, inspect the general condition of the tool. Check for:
   • loose hardware
   • misalignment or binding of moving parts
   • damaged cord/electrical wiring
   • cracked or broken parts
   • dull or damaged Saw Chain
   • any other condition that may affect its safe operation.

2. BEFORE EACH USE, tension Saw Chain and add bar and chain oil to oil reservoir.

3. PERIODICALLY OR WHEN REPLACING SAW CHAIN, turn the Guide Bar over to distribute the wear on it. Replace the Guide Bar when bent, cracked, or when the Saw Chain moves excessively from side to side on the Guide Bar due to wear (see Determining Guide Bar Wear on page 13).

4. AFTER USE:
   a. Remove Drive Cover, Saw Chain and Guide Bar.
   b. Scrape debris loose from inside Drive Cover and around Drive Sprocket, then wipe with a clean cloth and mild soap and water. Do not use solvents. Do not immerse the tool in liquid.
   c. Remove sawdust and sap from the Guide Bar’s Groove using a bar groove cleaning tool (sold separately).
   d. Wipe Guide Bar with a clean cloth, including oil passages, then lubricate with bar and chain oil.
   e. Wipe debris from Saw Chain, then lubricate with bar and chain oil.
   f. Replace Guide Bar, Saw Chain, and Drive Cover, leave Saw Chain loose during storage.
   g. Clean outside surfaces with a clean, dry cloth. If necessary use mild soap and water.
   h. Place Chain Cover over Saw Chain, then Store Pole Saw in a dry, secure location away from children.

5. WARNING! TO PREVENT SERIOUS INJURY: If the supply cord of this appliance is damaged, it must be replaced only by a qualified service technician.

Sharpening/replacing Saw chain

1. Have the cutters sharpened by a qualified technician when:
   a. The sawdust becomes powder-like.
   b. You can’t make the cut without extra force.
   c. The Pole Saw does not cut straight.
   d. Vibration increases.

2. A Saw Chain that is damaged or too worn to be restored by sharpening will need to be replaced.

Replacing Drive Sprocket
Have the Drive Sprocket replaced by a qualified technician when the Saw Chain is replaced?

Determining Guide bar Wear
The rails of the Guide Bar groove should always be parallel to each other. Place a ruler along the side of the Guide Bar and Saw Chain. If there is a gap, the bar is normal.

If the ruler is flush with the Guide Bar and Saw Chain, or the Chain tilts to one side, then the Guide Bar is worn and needs to be replaced.

Parts list and Diagram

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT. THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS. AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO. OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts list

Record product’s Serial number Here:
Note: If the product has no serial number, record the month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable. Specify number when ordering Specify UPC 193175371263 when ordering parts.

Assembly Diagram

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear, and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS  EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Item 56808
For technical questions, please call 1-888-866-5797.
26541 agoura road • calabasas, ca 91302 • 1-888-866-5797

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>