HTZSAFE 806A+T904 Wireless Alarm System User Manual
- June 6, 2024
- HTZSAFE
Table of Contents
HTZSAFE 806A+T904 Wireless Alarm System
Note:
- The alarm system is pre-programmed , please proceed to part 2 of the manual for setup. (Or please search “HTZSAFE T904&806A SETUP“ on YouTube, there is a video for your reference)
- If you want to add additional HTZSAFE sensors to the system, program them according to part 3 of the manual or contact us directly. (Or please search
“HTZSAFE T904 to 806A Connect “ on YouTube, there is a video for your reference)
After-sale Service:
E-mail: contact@saferhomee.com
System Components And Usage
Plug-in Alarm Receiver
Power Plug:plug the receiver into a socket
Volume: 4 adjustable volume levels
Melody: 35 optional melodies
Zone Number: flash for several seconds when the sensor be
activated
Speaker: sound for several seconds when the sensor be activated
Solar Wireless Motion Sensor
Sensor Eye: detects heat movements
Solar Panel: charges the built-in battery of the sensor
Charge Jack: used to connect the additional solar panel or DC 5V power
adapter
ON/OFF: sensor on/off
ATTENTION PLEASE
The KIT includes a USB charging cord without a AC adapter which is used to
manually charge the solar sensor before use or after pro-longed low light
conditions causing low battery.
Please kindly connect the charging cord with your own USB plug(such as the
direct USB outlet, the phone’s USB plug or computer’s USB, etc.).If
needed,please charge the sensor for 4 hours with the USB charging cord as
below:
Operation Instructions
Step 1
Plug the receiver into an outlet
Ring tone prompt and the zone number will
light up one by one for 3 times meaning the receiver works properly.
Step 2
Turn on the Wireless Motion Sensor: Press the ON/OFF button 4 times
(bleep
prompt meaning normal operation)
Step 3
Activate The Wireless Motion Sensor (wait about 30 seconds after you turn on
the sensor)
1st method :press the ON/OFF button twice
(the light of the ON/OFF button
will flash once meaning the motion sensor was activated and sent the wireless
signal)
2nd method: Walk through in front of the sensor to acivate
(the light of the ON/OFF button will flash once meaning the motion sensor
was activated and sent the wireless signal;then the motion sensor will
automatically reset after
a few seconds ready for next trigger)
Step 4
Press “Melody” once to choose the melody for this sensor, total 35 optional
melodies.
Step 5
Same operation if you have the additional sensor,and please refer to part 3 of
the manual for other settings.
Step 6
Installation
Wireless Motion Sensor
Installation Notes:
Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.
- Please point the sensor towards a open field (not towards the trees or bushes)
- please adjust the sensor a little down(never upwards)
- please point the sensor eye towards to the engine or exhaust pipe if detecting vehicles.(the working principle of the senor is detecting the movements with heat sources)
Other Settings
-
How to add additional sensors to the receiver
(up to 4 sensors can be added to one or multiple receivers)
Step 1
Plug the receiver into an outlet
Step 2
Press and hold the “Volume” button for 5 seconds, release the button when one of the zone number flashing and a beep prompt
Step 3
Activate the sensor.
Note: please have the sensor close to the plug-in receiver when programming.(within 30FT )
(the light of the ON/OFF button will flash
once meaning the motion sensor was activated and sent the wireless signal)
(Zone number flashing quickly and a ring tone prompt meaning the sensor has been added to the plug-in receiver properly)
Step 4
Activate the sensor again to confirm the sensor has been added to the receiver already.
Step 5
Press”Melody”button to choose the melody for this sensor. total 35 optional melodies .
Step 6
Same steps to add more sensors to the plug-in receiver. (For example: add the 2nd sensor to the receiver) Press and hold the “Volume button” for 5 seconds —–release the button when the Zone 2 flashing slowly (zone 1 lights up meaning one sensor has been added to zone 1 already)—-activate the 2nd sensor once —-Zone 2 flashing quickly and a ring tone prompt meaning the 2nd sensor has been added to the receiver.
Note please: the receiver has 4 zones and up to 4 sensors can be added to 1 receiver.(the receiver will have a long beep prompt if you operate to add more than 4 sensors
to 1 receiver) -
How to delete the sensors of the receiver
Step 1
Plug the receiver into an outlet
Step 2
Press and hold both the “Volume” button and “Melody” button for 10 seconds and release the buttons when you hear a long beep prompt;
Note: all the sensors will be deleted by this operation.
-
How to adjust the volume
Step 1
Plug the receiver into an outlet
Step 2
Press the “Volume” once to adjust the volume of the receiver. (total 4 adjustable volume levels)
-
How to change the melody for the sensors (total 35 optional melodies,you can match a different melody for each sensor)
Step 1
Plug the receiver into an outlet
Step 2
Activate the sensor first,and then press the “Melody” button to choose the melody for this sensor
Repeat steps for other sensors which have been added to the receiver already. -
How to adjust the sensitivity of the sensor
The sensor has 3 adjustable sensitivities(Low,Medium,High)
Step 1
Turn off the sensor first Press the ON/OFF button 3 times to turn off the sensor
(it will long beep prompt)
Step 2
To select Low sensitivity—-turn on the sensor by pressing the ON/OFF button 3 times.
To select Medium sensitivity—-turn on the sensor by pressing the ON/OFF button 4 times.
To select High sensitivity—-turn on the sensor by pressing the ON/OFF button 5 times.
Technical Parameters
Plug-in Alarm Receiver
Technical parameters
| Item | Technical Parameters |
|---|---|
| Working Voltage | AC 110V-220V |
| Working Current | Static Current 20mA; Alarming Current 300mA |
| Wireless Frequency | 433MHz FSK+FHSS |
Wireless Motion Sensor
Technical parameters
| Item | Technical Parameters |
|---|---|
| Detection Range | Low=25feet(7.5m) |
Mid=50feet(12m) High=70feet(21m)
Detection Angle| 15
Wireless Transmission Range| 1/2 Mile(800m)
Wireless Frequency| 433MHz FSK+FHSS
Working Voltage| 3.3V
Battery Type| Chargeable LiFePO4 Battery
Battery Capacity| 500mAh
Working Current| Static: 1mA; Alarming:60mA
Solar Panel Output Current| ≥100mA in Sunny days
Working Temperature Range| -22°F to 158°F(-30℃ to 70℃)
After-sale Service:
E-mail:contact@saferhomee.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>