JASCO 54850/54851 UltraPro Outdoor Simple-Set Plug-In Grounded Outlet Timer Instruction Manual
- June 6, 2024
- JASCO
Table of Contents
54850 & 54851
OUTDOOR SIMPLE-SET PLUG-IN
GROUNDED OUTLET TIMER
Read instructions or watch the easy-to-follow videos.
Scan QR code or visit https://byjasco.com/54850i
IF MOUNTING OUTDOORS
- Mount the timer on a wall near a GFCI receptacle using a screw or nail. Install timer as far above ground level as possible with receptacle facing downward. Do not install where the timer can be immersed or where water will splash or drip onto the receptacle. Screw or nail head must extend at least 3/16in. from the wall (nail or screw not included).
- Hang the timer from the hole at the top of the unit.
SETUP
- If numbers are difficult to read or not visible on-screen, plug the timer into an outlet and let the timer charge for 1 hour. Once charged, press the reset (R) button in the lower right corner using a toothpick or pencil.
- Use up ( ) and down ( ) arrows to set current time. Take note of the AM/PM setting.
Note : When daylight saving time occurs use the up ( ) and down ( ) arrows to adjust the time by 1 hour.
PROGRAMMING OPTIONS
DEFAULT TIMER
There are two ON/OFF times available with preset default times. To activate
default times, simply press the ON TIME or OFF TIME button so the arrow ( )
next to the setting is visible on the display. To deactivate the default
timer, press and release the button. The arrow next to the setting will
disappear.
CUSTOMIZED TIMER
On-time: Press and release either ON TIME button to enter custom setting mode.
The default on time flashes. Use arrow buttons ( ) to set the desired on time.
Press the ON TIME button or wait 5 seconds to set. If no button is pressed
within 5 seconds, the default timer will be set and the display will return to
clock mode. If you set the on-time earlier than the current time, it will not
turn on until the next day at the scheduled time.
Note : Mode indicator ( ) will move under SET while programming, then
back to CLOCK if it times out or after on time is set.
Off time: Press and release either OFF TIME button to enter custom
setting mode. The default off time flashes. Use arrow buttons ( ) to set the
desired off time. If no button is pressed within 5 seconds, the default timer
will be set and the display will return to clock mode. Press the OFF TIME
button or wait 5 seconds to set.
Note: When an on-time or off time is set, the active program indicator ( or )
will appear on the screen beside the setting. Programs may run individually
or simultaneously.
FCC/IC
Supplier Declaration of Conformity | Model #: 54850, 54851 | Jasco Products
Co., 10 E. Memorial Rd., Oklahoma City, OK 73114,
www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-
exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the
receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
SPECIFICATIONS
125VAC, 50/60Hz
10A 1250W general/resistive
5A 625W tungsten
1/4HP motor type 3R
Works with dimmable LED and CFL bulbs
WARNING
RISK OF ELECTRICAL SHOCK
- PLUG DIRECTLY INTO A GFCI PROTECTED OUTLET
- UNPLUG TIMER BEFORE CLEANING
- FULLY INSERT PLUG
- KEEP AWAY FROM CHILDREN
- NOT FOR WATER IMMERSION
- SUITABLE FOR INDOOR AND OUTDOOR LOCATIONS, STORE INDOORS WHILE NOT IN USE
RISK OF FIRE
- DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.)
- DO NOT EXCEED ELECTRICAL RATINGS
- DO NOT USE IF DEVICE OR CORD IS DAMAGED
- DO NOT USE WITH AN EXTENSION CORD
MADE IN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City,
OK 73114.
This Jasco product comes with a 2-year limited warranty. Visit
www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between
7 AM-8 PM M-F, Central Time.
©JASCO 2020 | 54850, 54851 | 09/08/20 v1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>