KINGSTON KS4100DL Brass Pot Filler Instruction Manual
- October 27, 2023
- Kingston
Table of Contents
INSTALLATION INSTRUCTIONS
Pot Filler
Parts:
| Mounting Screw & Anchor | Set Screw |
|---|---|
Need Tools:
BEFORE BEGINNING INSTALLATION:
- Flush plumbing lines to clear any debris.
- Shut off both supply lines after flushing.
| 1. Shut off hot and cold water supply under sink. Plug sink drain with
cloth to avoid losing small parts. Remove old faucet.
---|---
| 2. Turn on old faucet to remove any excess water in the supply lines. Apply
Teflon tape onto the threads of supply elbow.
| 3. Insert mounting plate into the faucet body and install to water outlet
on wall.
| 4. Place the mounting plate in the center of the pencil outline you just
made and mark the location of the mounting screws.
| 5. Drill holes at the marked locations and remove mounting plate from
faucet body.
| 6. Insert anchors into the holes with a hammer until flush with the wall.
| 7. Screw the mounting plate to the wall with the mounting screws.
| 8. Insert flange into the faucet body and install to water outlet on wall
then turn tightly in a clockwise direction.
Make sure the faucet is horizontal.
| 9. Tighten the set screw with the Allen wrench then cover the mounting
plate with the flange.
| 10. Install the handles with the screws and replace the covers.
| 11. Remove aerator and turn on both hot and cold valves, let water run for
at least one minute, this will clear any debris left in the line, reinstall
aerator.
Parts:
CARE AND MAINTENANCE OF YOUR FAUCET
Your Kingston Brass faucet has been finished to the most strict standards;
however, due to the high content of minerals in the water, your finish may
appear dull and tarnished after time.
These are some do’s and don’ts to maintain the luster on your faucet for many
years to come.
DO
- Use a silicon based caulking when installing.
- Clean your faucet with only a mild soap and water solution.
- Dry your faucet after using it.
- Give it a coat of Carnauba Wax periodically.
DON’T
- Use plumbers putty when installing the faucet.
- Use any abrasive cleaning agents.
It may seem like a very simple and short list but it is that simple to maintain your faucet, looking shiny and new.
If your faucet is already looking somewhat dull and tarnished, before replacing it, try cleaning it with a 50/50 solution of vinegar and water, you may need to soak some rags and wrap around those stubborn areas, leave overnight and rinse completely in the morning, apply Carnauba wax once you have removed the mineral deposits.
Kingston Brass” Faucets
(10) YEARS LIMITED WARRANTY
Kingston Brass warrants its faucets to be flawless during normal residential
use. If the faucet should leak or drip during normal use, Kingston Brass will,
free of charge, mail to the original owner the cartridge necessary to put the
faucet in good working condition. All warranty parts to be shipped freight
prepaid ground service. Customer will be responsible for all warranty part
freight charges if express shipping is requested. This warranty applies only
to Kingston Brass Faucets installed in the United States of America only.
Kingston Brass also warrants all other aspects of the faucet or accessories
(except Oil Rubbed Bronze and Dark Bronze Finishes on color changes as part of
the normal living finish behavior) to be free of defects in material and
workmanship during normal residential use within (10) years from the date of
purchase to its original owner. If a defect is found in normal residential
use, Kingston Brass will, at its selection, repair, provide a replacement part
or product, or make appropriate adjustment. Damage to a product caused by
accident, misuse, or abuse is not covered by this warranty. Improper care and
cleaning will void the warranty.
Proof of purchase (original sales receipt) must be provided to Kingston Brass
with all warranty claims.
Kingston Brass is not responsible for labor charges, installation, or other
incidental or consequential costs. In no event shall the liability of Kingston
Brass exceed the purchase price of the faucet.
SPECIAL FINISHES:
Warranty does not apply to special or living surface finishes such as Oil
Rubbed Bronze, Dark or Old Bronze as living finishes will change over time as
a result of a normal process and may look different than at the time of
purchase, therefore these items are warranted for functionality only. Oil
Rubbed Bronze, Dark or Old Bronze components may vary in shade at the time of
shipment. This warranty is limited to the replacement of defective parts only,
labor charges and/or damage resulting from improper installation, repair or
replacements, as well as incidental and consequential damages connected
therewith are excluded.
Any damage to this faucet as a result of misuse, abuse, neglect, accident or
improper installation or any use not consistent with the instructions
furnished by us, will void this warranty.
CAUTION!!!
- Prior to installing the faucet, water lines must be flushed clean of debris and particles that may be present to avoid the clogging of cartridges or aerator causing mal-function, leakage or reduce in flow.
- Warranty will be void if water lines are not properly flushed prior to installing the faucet.
- Use of abrasives cleaners of any strength may damage the finish of your faucet and will void this warranty.
To obtain warranty service, contact the Dealer, Plumbing Contractor, Home Center or E-tailer, or contact
Kingston Brass by calling 1-877-252-7277 or write to Attn: Warranty Department, 12775 Reservoir Street, Chino, CA 91710.
Kingston Brass” Cast Iron Tubs, Acrylic Tubs, Toilets, Vessel Sinks, Wash Basins, and Stainless Steel Sinks.
ONE-YEAR LIMITED WARRANTY
KINGSTON BRASS Sinks, tubs and toilets are warranted to be free of defects
in material and workmanship for one year from date of installation. Kingston
Brass will, at its selection, repair, replace or make appropriate adjustment
where Kingston Brass inspection discloses any such defects occurring in normal
usage within one(1) year after purchase to its original owner. Proof of
purchase (original sales receipt) must be provided to Kingston Brass with all
warranty claims. Kingston Brass is not responsible for removal or installation
costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service, contact the Dealer, Plumbing Contractor, Home
Center or E-tailer, or contact Kingston Brass by calling 1-877-252-7277 or
write to Attn: Warranty Department, 12775 Reservoir Street, Chino, CA 91710.
Some states/provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of special, incidental or consequential
damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights. You may also have other rights which
vary from state/province to state/province.
- Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents or other products not recommended for chrome. This will void the warranty.
10 YEAR MANUFACTURER’S LIMITED WARRANTY
All parts of this Kingston Brass faucet are warranted to the original retail
purchaser to be free from defects in material and workmanship for a period of
Ten(10) years from the date of purchase as shown on the purchaser’s receipt.
This warranty Is limited to defective parts only, labor charges and/or damage
resulting from improper installation, repair or replacements, as well as
incidental and consequential damages connected therewith are excluded.
Any damage to this faucet as a result of misuse, abuse, neglect, accident, or
improper installation or any use not consistent with the instructions
furnished by us, will void this warranty.
Replacement parts can be obtained from your local dealer. Freight cost is not
covered by manufacturer.
CAUTION!!!
- Water lines must be completely flushed before use, to avoid debris & clogs in your water system leading to reduction of water flow and mal-functioning.
- Warranty is void if water lines are not flushed prior to use and installation of the new faucet.
- Use of abrasives of any strength may damage the finish of the faucet and void the product warranty.
- Do not over tighten your faucet on the countertop during installation. The valve assembly Is tested to meet the standards set by ASME A112.18.1 sec 5.8 which is listed at 100 LBF. However, over-tightened or over-torqued nuts may lead to cracks on the valve and will eventually lead to leaking and water damage.
- Before installation of the faucet to the desired fixture, you need to secure and anchor your console, sink, tub, or vanity cabinet firmly to the wall and to the floor. To ensure your fixture or faucet mounting surface cannot be moved, before installation of the faucet, please test to see if the cabinet or vanity can be moved by hand or body weight. If the faucet mounting fixture is not secure and anchored, it will eventually crack the valve and cause leaking leading to property damage. In order to avoid this, be sure to secure your installation surface. Do not use any Power Tools for assembly and installation which can cause internal fractures to the fixture.
PROBLEMS SHOOTING
| PROBLEM | CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Leaks underneath handle | Bonnet nut has come loose | Remove the handle and |
tighten the bonnet nut
Leaks from the spout| Valve seat and spring are worn| Replace the valve seat
and spring
Inconsistent water flow pattern| Aerator is dirty or aged| Release aerator and
check on rubber gasket if aged or replace with a new aerator
Faucet is dirty| Caused by stubborn water spot| Clean with mild soap and warm
water as often as possible
Handles work backward| Handle installed backward| Rotate the right stem stop
assembly 180 degrees
CODE APPROVAL: LA#M-000018
www.kingstonbrass.com
TOLL-FREE CUSTOMER SERVICE: 1-877-2-KBRASS
TECHNICAL SUPPORT E-mail:
service@kingstonbrass.com
12775 Reservoir Street, Chino, CA 91710
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>