Midea FS40-16JA Stand Fan Owner’s Manual

ELECTRIC FAN

OWNER’S MANUAL
STAND FAN
MODEL: FS40-16JA

READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.

CAUTION
Read Rules for Safe Operation and Instructions Carefully.
WARNING

1. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
2. To protect against the risk of electrical shock, do not immerse the unit, cord, or plug in water or other liquid.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
4. When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
5. Keep electrical appliances out of reach from children or infirm persons. Do not let them use the appliances without supervision.
6. When the fan was assembled, the rotor blade guard shall not be taken off anymore
   – Prior to cleaning unplug the fan.
   – The rotor guard shall not be dissembled/opened to clean the rotor blades.
   – Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the grille when the fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure the fan is on a stable surface when operating to avoid overturning.
4. DO NOT use the fan in the window, rain may create an electrical hazard.
5. Household use only.

PARTS NAME

Note: All the pictures in this manual are for explanation purposes only. Any discrepancy between the real object and the illustration in the drawing shall be subject to the real subject.

ASSEMBLY OF CROSS STAND & COLUMN UNIT

1. Loosen 4 sets of screws, washers, and spring washers which are fitted in the center section on the stand, and assembly the extension pole onto the base
   enclosure with these screws originally. (Fig.1)

2. Loosen the height adjustment ring, lift the internal pole to the max height and prevent the internal pole from slipping into the extension pole, then screw out the height adjustment ring. (Fig.2)

3. To attach the stand ornament (cover for the stand), slide the stand ornament down the extension pole. (Fig.3)

4. Reattach the height adjustment ring. (Fig.4)

5. From the extension, the pole loosens the height adjustment ring and adjusts the internal pole to the desired height. (Note: If you can’t find the internal pole, it slides inside the extension pole. You can pull it out from the extension pole.) (Fig.5)

6. To attach the head unit to the internal pole, loosen the thumbscrew on the bottom of the head unit. Place the head unit on the internal pole and tighten the thumbscrew in alignment with the groove on the internal pole. (Fig.6)

GRILL & FAN BLADE ASSEMBLY

1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut counterclockwise to remove both of them. Fix the rear grill to the motor then tighten the plastic nut again. (Fig. 7)
2. Insert the blade into the shaft, and make sure the rotor shaft pin is fitted into groove of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig. 8)
3. Fasten the front grill and the rear grill by the grill clip and then tighten the fan grill locking screw and nut. (Fig. 9)

OPERATING INSTRUCTION

1. Speed is controlled by the Piano switch:
   0—Off 1—Low 2—Medium 3—High

2. To make/stop the fan head oscillating. Push down/pull up the clutch knob.

3. To adjust the airflow upward or downward, push the grilles lightly to the desired direction.

4. The height of the fan can be adjusted by loosening the height adjustment ring, carefully carefully raising or lowering the fan, and firmly re-tightening the height adjustment ring.

MAINTENANCE INSTRUCTION

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified service personnel if service is needed.

1. Before cleaning and assembling, the fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.

CLEANING

1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moistened with mild soap. Thoroughly remove soap film with a dry cloth.

DISPOSAL： Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

GD Midea Environment Appliances MFG.Co., Ltd.
No.28, Dong Fu Road, Hesui East Industrial Area, Dong Feng Town,
Zhongshan, Guangdong 528425 P.R.China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>