ergotron Neo-Flex Dual WideView Workspace User Guide
- June 6, 2024
- ERGOTRON
Table of Contents
Neo-Flex” Dual
WideView Workspace
** User Guide**
Features & Specifications
| CPU Holder
---|---
CPU Holder NOTE: If you are not attaching a CPU to your cart, skip step 2 and proceed to step 3.
Caution: Do Not overtighten fasteners. Over-tightening may cause damage to fasteners.
NOTE: Position at bottom of the tower. Do not tighten at this time.
Tipping Hazzard : Position bracket so that CPU
attaches as low as possible on the tower.
WARNING
DO NOT load Cart below the minimum or above maximum weight capacities. DO NOT
mount a display larger than the recommended size. Failure to comply with a
warning may result in Cart instability leading to equipment damage or personal
injury.
10 Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if the product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
Follow these instructions to tighten or loosen tension.
WARNING
DO NOT load Cart below the minimum or above maximum weight capacities. DO NOT mount a display larger than the recommended size. Failure to comply with a warning may result in Cart instability leading to equipment damage or personal injury.
WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Minimize Lift Tension BEFORE
Removing Mounted Equipment.
To Minimize Lift Tension
1. Lower the work surface to the lowest position.
2. Turn adjustment nut at top of riser counterclockwise until it stops (may
require 40-60 turns to minimize lift tension).
3. After removing or adding equipment adjust lift tension to compensate for
the weight of the new load.
Failure to heed this warning may result in serious personal injury or property
damage!
WARNING
STORED ENERGY HAZARD!
DO NOT OPEN THE TOWER OR BASE. DO NOT REMOVE THE SAFETY GUARD.
A primary mechanism within the Cart is under tension and can be hazardous to
people exposed to it under certain conditions.
DO NOT open the Cart tower or base.
DO NOT attempt to service the Cart.
DO NOT remove safety guards or labels designed to protect or inform of
possible hazards.
Only Ergotron-approved installers may service or otherwise modify Cart.
Failure to heed this warning may result in serious Personal Injury and Damage
both to the cart and equipment. 240-027-00
WARNING
TIPPING HAZARD!
DO NOT allow children to climb on Cart.
DO NOT route electric cords or equipment cables within reach of children.
LOCK CASTERS when Cart is stationary.
DO NOT move Cart with Display in the highest position.
DO NOT move Cart over cords or uneven, dirty, soft, or sloping surfaces.
DO NOT move Cart by pushing on Display.
Failure to comply with this warning may result in Cart instability leading to
equipment damage or personal injury.
TO MOVE CART
- Push Display down to lowest position.
- Disconnect the power cord and secure it to Cart.
- Unlock casters; point casters in direction of travel.
- Use the rear handle to push Cart.
Learn more about ergonomic computer use at:
www.ergotron.com/ergonomics
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit:
http://contact.ergotron.com
www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: japansupport@ergotron.com
© 2014 Ergotron, Inc. All rights reserved. Neo-Flee is a registered trademark
of Ergotron, Inc.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording, or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
888-24-076-W-00 rev. J • 11/20
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>