ergotron Dual Monitor Kit User Manual
- June 6, 2024
- ERGOTRON
Table of Contents
User’s Guide
Dual Monitor Kit
for WorkFit-T, TL, TLE, TX, and Corner Desk Converters 
For the latest User Installation Guide please visit: www.ergotron.com
www.ergotron.com I USA:
1-800-888-8458 I Europe: +31 (0)33-45
45 600 I China: 400-120-3051 I Japan:
[email protected]
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if the product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Warning: Impact Hazard! Moving Parts can Crush and Cut.
Raise worksurface to top of vertical adjustment BEFORE removing equipment.
**Failure to heed this warning may result in serious personal injury and or
property damage!**
Warning:
Impact Hazard! Moving Parts can Crush and Cut.
Raise monitor to the top of vertical adjustment before removing.
WorkFit-T: 25.3 lbs (11.48 kg)
WorkFit-TL: 30.3 lbs (13.74 kg)
WorkFit-TLE: 30.3 lbs (13.74 kg)
WorkFit-TX: 30.3 lbs (13.74 kg)
WorkFit-Corner: 25.3 lbs (11.48 kg)
WorkFit -T, TL, TLE
WorkFit -T Corner
WorkFit – TX
NOTE: Leave enough slack in the cable to allow full range of motion. Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury.
Adjustment Step
Important! You will need to adjust this product after installation is
complete. Make sure all your equipment is properly installed on the product
before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are
too easy or diffi cult or if the product does not stay in desired positions,
follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice
a diff erence. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat
these adjustment steps to ensure safe and optimum operation. 
Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when
raised, then you’ll need to increase Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or this product does not stay down when
lowered, then you’ll need to decrease Lift Strength:
Ready to get moving on an active workstyle? Check out
www.ergotron.com/tips to get started.
Learn more about ergonomic computer use at:
www.ergotron.com/ergonomics
ww.ergotron.com | USA:
1-800-888-8458 | Europe: +31 (0)33-45
45 600 | China: 400-120-3051 | Japan:
[email protected]
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contactergotron.com
© 2014 Ergotron, Inc. All rights reserved.
While Ergotron, inc makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording, or otherwise
without the prior written consent of Ergotron, inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S.& Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
888-97-374-G-01 rev.L • 11/20
Documents / Resources
|
ergotron Dual Monitor
Kit
[pdf] User Manual
ergotron, Dual Monitor Kit
---|---