little tikes 654046M My First Pet Checkup Set Installation Guide

: June 6, 2024
: Little Tikes

3+

654046M

My First Pet Checkup Set™
ASSEMBLY INSTRUCTIONS
Adult assembly required. Approx. assembly time: 25 min.

Look for a video of assembly at
littletikes.com/videoinstructions
XIM654046 – 7/20

Thank you for choosing the Little Tikes© My First Pet Checkup Set™. We strive to provide a durable, easy-to-assemble toy that’s made to last, giving your child years of imaginative, engaging fun!

Really important information you should know!

Read through all the instructions first.
Clear a flat surface to lay out all the materials so everything is close at hand.
You will need a Phillips head screwdriver (not included) to assemble the My First Pet Checkup SetTM.
– When installing screws, be sure screws are tightened snugly, but do NOT OVERTIGHTEN.
Be sure to locate your decals and set them aside. Some decals are easier to apply when the part is
laying flat, so you may want to apply the decals before assembly (steps 14 & 16).
The parts are listed below – each part is identified with a letter in RED for easy reference.
Illustrations are for reference only. Styles may vary from actual contents.
If you have any questions, we’re here to help. Give our customer service team a call at 1-800- 321-0183.

Let’s be careful!

WARNINGS!

Adult Assembly Required
Keep these instructions as it contains important information.
Prior to assembly, this package contains small parts: hardware which is a choking hazard and may contain sharp edges and sharp points. Keep away from children until assembled.
This product is intended for indoor family use only.
This product is intended for use by children ages 3 years and up.
Do not allow children to sit, stand, play or climb on the top surface. Failure to do so may cause the product to become unstable.
Protect your eyes. Always wear safety glasses when using power tools.

WARNING!

CHOKING HAZARD-Small parts. Not suitable for children under 3 years.
Markers will stain fabric and other surfaces.
To better clean, the product uses cloth with mild soap and water or skin, hand, or face wipes.

Battery Safety Information. This is serious!

Keep these instructions for future reference.
Requires 3 “AAA” (LR03) alkaline batteries (not included). (Rechargeable batteries may be substituted.)
The voltage of a fully-charged, rechargeable battery is often lower than that of a fresh alkaline battery. Therefore, it is recommended that alkaline batteries be used instead of rechargeable batteries for best performance and longer playtime.
Install batteries with the correct polarity (+ and -).
To avoid battery leakage:

Follow the toy and battery manufacturer’s installation instructions.
Do not mix old and new batteries.
Do not mix standard (carbon-zinc), alkaline or rechargeable batteries. Do not mix different brands of batteries. Only batteries of the same or equivalent type as recommended are to be used.
When the toy is not used for an extended period of time, remove batteries to prevent possible leakage and damage to the unit.
Remove dead or exhausted batteries from the product.
Dispose of dead batteries properly; do not bury them. Do not dispose of batteries in a fire as they may leak or explode.
· Make sure the cover is properly installed on the unit at all times.
· Do not attempt to recharge non-rechargeable batteries.
· Rechargeable batteries are to be removed from the toy before recharging.
· Charging of rechargeable batteries should be done by an adult.
· The supply terminals are not to be short-circuited.

NOTE: If the unit stops working or doesn’t work as it should, remove the batteries for a few minutes and then re-insert them. If there is still a problem, install new batteries.

FCC COMPLIANCE

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Modifications not authorized by the manufacturer may void users’ authority to operate this device. This Class B digital apparatus complies with Canadian ICES-003.

` ****Let’s care for the environment!’ The wheelie bin symbol indicates that the product must not be disposed of with other household waste. Please use designated collection points or recycling facilities when disposing of the item. Do not treat old batteries as household waste. Take them to a designated recycling facility.

A Few Things Before You Start!

BEFORE you begin assembly, make sure you have all the parts listed below.

Some packages of hardware may have extra pieces.

Questions? We’re here to help.
Little Tikes customer service team at 1-800- 321-0183.

|
---|---

Illustrations are for reference only.
Styles may vary from actual contents.

Accessories

Ready…let’s start!

Battery installation MUST be completed by an adult:

Using a Phillips screwdriver (not included) remove the screw and battery compartment covers (2) located on the light.
On the left side of the light, install two (2) fresh AAA alkaline batteries (not included), making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment.
On the right side of the light, install one (1) fresh AAA alkaline battery (not included) making sure the (+) and (-) ends face the proper direction as indicated inside the battery compartment.
Replace the compartment cover and tighten the screw.

Simple to start

First, place the Left side – front wall (part B) onto the Right side – front wall (part A). Second, secure using (2) 1 /2” (1,27 cm) screws.

Get Snappin’

Snap (1) side (part J) onto the assembled front walls.
Make sure ALL (4) tabs line up before snapping!
If they don’t line up – flip the side around.

Snap (1) side (part J) onto the opposite side of assembled front walls.

Flip it

Turn the unit upside down and snap on the bottom platform (part F).

The countertop is a SNAP!

Turn the unit right side up and snap on the countertop (part G).

This is tricky

Snap-on side exam table support (part E).
Check to be sure you install the shelf on the correct side!

Swing it in

Pop-in the side exam table (part D) into the countertop.

Still more to swing

Swing table supports upward and snap it into the underneath of the side exam table.

You gotta have a faucet!

Insert the faucet (part M1) into the countertop and secure it by attaching the faucet fastener (part M2) under the countertop from the back of the unit.

1…2…3…

Insert the light arm (part L1) into the hole located on the top back wall (part C). Hold in place while fitting the top shelf (part H) over the arm and onto the top back wall.

Get down with it

First, fit assembled top back wall onto countertop Second, secure using (6) 1 /2” (1,27 cm) screws.

Key it in. Pop it on.

Insert scale (part K) into the top shelf.
Pop light (part L2) onto the light arm.
Almost there!!!

Fit clear panel (part I) onto the rear of the back wall. Align the holes. Second, secure using (6)1/2” (1,27 cm) screws.

Clip it on

Insert 2 clips (part O) into the side, next to the scale.

Sticker it up

Decal (1) MUST be applied before knobs are installed. Apply decal (2) to the back wall.

Turn it on

PUSH in (2) knobs (part N) onto the front control panel.

Plug it up!

PLUG the remaining holes with the (4) remaining hole plugs.

Time to PLAY!!!

To insert x-ray slide

© The Little Tikes Company, an MGA Entertainment company. LITTLE TIKES® is a trademark of Little Tikes in the U.S. and other countries. All logos, names, characters, likenesses, images, slogans, and packaging appearance are the property of Little Tikes. Please keep this address and packaging for reference since it contains important information. Contents, including specifications and colors, may vary from photos depicted on the package. Instructions included. Please remove all packaging including tags, ties & tacking stitches before giving this product to a child.

CONSUMER SERVICE:

United States:
www.littletikes.com
1-800-321-0183 Monday – Friday
The Little Tikes Company
2180 Barlow Road
Hudson, OH 44236
E-mail: service@littletikescare.com
Printed in the U.S.A. D.R.©2020 The Little Tikes Company

United Kingdom:
www.littletikes.co.uk
Little Tikes, MGA Entertainment (UK) Ltd
50 Presley Way
Crownhill
Milton Keynes MK8 0ES
Bucks, UK
Tel: +0 800 521 558
E-mail: support@LittleTikesStore.co.uk

Australia
www.littletikes.com.au
Imported by MGA Entertainment Australia Pty Ltd
Suite 2.02, 32 Delhi Road
Macquarie Park NSW 2113
1 300 059 676

LIMITED WARRANTY

The Little Tikes Company makes fun, high-quality toys. We warrant to the original purchaser that this product is free of defects in materials or workmanship for one year from the date of purchase (dated sales receipt is required for proof of purchase). At the sole election of The Little Tikes Company, the only remedies available under this warranty will be the replacement of the defective part or replacement of the product. This warranty is valid only if the product has been assembled and maintained per the instructions. This warranty does not cover abuse, accident, cosmetic issues such as fading or scratches from normal wear, or any other cause not arising from defects in material and workmanship. The warranty period is three (3) months for daycare or commercial purchasers.

U.S.A and Canada: For warranty service or replacement part information, please visit our website at www.littletikes.com, call 1-800-321-0183 or write to Consumer Service, The Little Tikes Company, 2180 Barlow Road, Hudson
OH 44236, U.S.A. Some replacement parts may be available for purchase after the warranty expires—contact us for details.

Outside U.S.A and Canada: Contact the place of purchase for warranty service. This warranty gives you specific legal rights, and you may also have other rights, which vary from country/state to country/state. Some countries/states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

MINIMUM SIZE allowed is .2” high
Updated 12.2.11 per Paul Madan (new spacing)