Ultra Creation AM/FM Digital Clock Radio User Manual
- June 6, 2024
- Ultra Creation
Table of Contents
Ultra Creation AM/FM Digital Clock Radio
AM/FM DIGITAL CLOCK RADIO
Import notes
- Please review this manual and keep it safe so that you can refer to it at any time before operation.
- Computer systems , flulights , electric motors , motor vehicles , etc. can cause interference and should be avoided .
- While listening to AM station which depends on the hidden magnetic rod antenna, so you can adjust the unit location for the best reception. Also, the angle of the telescopic antenna can be elongated and turned in the direction for better FM reception.
- Do not let the backup battery that is about to run out be placed in the machine for too long, to avoid leakage causing damage to the parts.
- Avoid extensive moisture temperature environment above 40 ℃ or below 0 ℃.
- Place the unit on a flat and stable surface with good ventilation to avoid damage to the unit.
Important safety instructions
For United States:
Cautions to the user
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
RF exposure statements
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, the antenna(s)
used for this transmitter must be installed to provide a separation distance
of at least 20cm (8 inches) from all persons and must not be colocated or
operating in conjunction with any other antenna or transmitter. No change to
the antenna or the device is permitted. Any change to the antenna or the
device could result in the device exceeding the RF exposure requirements and
void user’s authority to operate the device.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guaranty that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of the electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to so.
Specifications
Main unit specification
Product size| LWH=11511060mm
Weight of the main unit| Pending
Power specification
Input voltage| DC5V±5%
Input current| <2A
Power consumption| <6W
Backup battery| AAA alkaline battery x 2
Battery life| Power down time＜30 times，single time ＜ 1hour，last for one year
Radio specification
Bands| AM/FM
Frequency range
| AM (9k): 522–1710 kHz
AM (10k): 520–1710 kHz
FM：64‐‐‐108MHz
Wi‐Fi parameters
Wi‐Fi protocol supported| 802.11.b/g/n
The connection distance| < = 100M (open and unobstructed range).
Display specification
Display parameters| 4 Digi 7‐segment white LED digital tube
The size of the display| 84*26mm
Audio specification
Speakers| 1.5‐inch 4‐ohm, /3W speaker
Amplifier parameters| 3W/4‐ohm mono output
TF card parameters
TF card protocol| Compatible with SDIO card protocol V3.0
Capacity is supported| Up to 64GB
Supported media file
Audio file| MP3/WMA/PCM (Reference only, Pending)
Environment parameters
Operating temperature range| 0℃ ～ +40℃
Storage temperature range| -20℃ ～ +55℃
Operating Humidity range| 45% ～ 80%RH
Storage humidity range| 30% ～ 90%RH
Controls
- Radio key
- Music key
- Scan key
- Menu/Setting key
- Select key
- Alarm1 key
- Alarm2 key
- Memory 1 key
- Memory 2 key
- Memory 3 key
- Memory 4 key
- Memory 5 key
- “‐“ Tuning down/previous key
- SNOOZE Key
- “+“ Tuning up/next key
- previous Voice message key
- current message playback key
- next Voice message key
- Message indicator light
- Volume swivel knob
- Telescopic antenna
- DC IN power jack
- Headphone jack
- Battery compartment
LED display
- White noise/music icon
- FM band icon
- AM band icon
- Frequency/time
- PM (Afternoon) icon
- AM (Morning) icon
- Alarm 1
- Alarm 2
Remote control
- On/OFF function key
- Tuning up key
- Tuning down key
- Timer key
- Source selection key
- Mute key
- Volume up key
- Volume down key
Power source
Use a suitable AC‐to‐DC adapter for input voltage 5V < 2A
Radio
Radio on/off
Press Radio key to turn on, then switch between AM/FM by Band key, pull out the lever antenna when you want to listen to the FM station. The display shows the band frequency for 15s, if you do not operate any key, it will return to the time display. Press Radio key again to check on the current radio frequency playing press and hold the Radio key for about 2 seconds to exit radio mode.
Turn off the station by timer
While listening to the radio, the display cycles through OFF/”30″/ “60”/ “90”/ “120” for each press of the Snooze key to set playback duration before radio turn of automatically. Select the duration you want until the display stops flashing and the setting is done. To cancel the setting by cycling the Snooze key to OFF, the radio will keep playing continuously.
Three ways to select radio frequencies Automatic scanning of the station
Press the Scan key move to the next available station, the display will shows the current radio frequency. Stay with it or press again for next station. The display will back to time display if no operation is done in 15 s.
Manual search
Press either “+” or “‐“once, the station frequency will go up/down in single step. Or, long press the “+” or “‐“ key for 2s, it will search for next available station. Stay with the station and display will back to time display or repeat for anther station.
Selecting your favorite station memory
When you’re listening to your favorite radio station, press and hold the memory “1 ‐ 5” button about 2S, the display frequency flashes, the radio station will be store at the key position. Repeating the same, the new station replaces the original station memory. To invoke a memory station, you can listen to it by clicking the corresponding key on the memory station “1 ‐ 5”.
Voice messages
This machine can playback voice messages sent by the SmartCukoo APP. (See the APP page diagram for details of the operation).
Voice message playback (unread)
If the Message indicator light flashes, press the button to play the latest message. During playback, the display showing the message date. If multiple messages exist, it will playback each automatically. The unit will go back to normal status in 3s after all messages was read.
Listened to voice playback
If you want to replay a voice message you’ve listened, press the key to play the last voice message you received. The message will playback once and go back to previous status in 3s. Press and backward for the voice message stored in the machine.
Delete the message
Click to display the most recent voice date on the display, hold down Select key, the display date will flash, the message will be deleted after holding the key about 2S. Other’s message can be deleted by repeating the process. Press or to select just the voice messages you want to delete and taking the above procedure . You can also use the APP to delete message individually or in bulk. (See app page diagram for more information about the operation).
White Noise playback
This machine stores 5 white noise selection (1 ‐ 5) by default.
White Noise / Music Play
Press the Music button and select white noise mode while the display icon lights up. Press the pre‐set “1 ‐ 5″ key to select tracks, or press “”+/‐” key to Loop through different tracks, the display shows the track number and the current time display will show up after 15S.
You can play more tracks, or you can replace the pre‐set favorite tracks inside the SmartCukoo APP (see app page diagram for more details). Press and hold the Music button 2S to exit music playback mode and the display icon disappears.
Clock / Date / Alarm
Clock/date settings
- When the unit is on, press Menu/Setting, the display will flash and enter clock/date
- The display shows 12H or 24H, it will switch between 12/24 by press scan key
- Press menu/Setting, the “hour” digit will flash, select the correct hour by pressing “+” or “‐ “, click Select key to Save.
- the “minute” digit will flash, select the correct minute by pressing “+” or “‐ “, click Select key to
- the “year” digit will flash, select the correct year by pressing “+” or “‐ “, click Select key to
- the “month” digit will flash, select the correct month by pressing “+” or “‐ “, click Select key to
- the “day” digit will flash, select the correct day by pressing “+” or “‐ “, click Select key to
- The display flashes and show current time setting, press the Menu/Setting key to complete the time date
Automatic clock/date setting
Start SmartCukoo APP, connect to the unit, and the clock will set synchronize as your mobile time.
Alarm setting
- Press Alarm1 or Alarm2, setting/ icon will flash, pressing the Menu/Setting, entering the alarm
- The “hour”, select the correct hour by pressing “+” or “‐ “, click Select key to
- The “minute”, select the correct minute by pressing “+” or “‐ “, click Select key to Save
- Go to source selection, press “”+/”‐” to select the desired ringtone; press Scan key switch to AM/FM band, press the “””+/”‐”” key to select the radio frequency, or select “1 ‐ 5” pre‐set station . Click Select
- The display back to the current time, press menu/Setting to complete the You will see theor icon on the display
- You can set up more alarm inside the SmartCukoo
SNOOZE feature
When the alarm started, press the SNOOZE key to silent the alarm temporally. It will ring again in 5 minutes by default until you actually stop the current alarm as above mentioned. (you can choose different setting inside the app).
Sleep settings
The Sleep function can allow you to define when the Radio or White noise playback time.
In the Radio or White noise playback mode, single press the SNOOZE key to cycle from “OFF”/ “30”/” 60″/”90″/”120″, stop pressing the SNOOZE key until you see your desire setting. The display will go back to current time in 15s and setting is done. Repeat the above process until you see “off” to cancel the timer.
Voice reminder
Schedule settings
Scheduled reminders can be set inside the app and playback from the unit.
(see app page diagram for details).
Stop and cancel reminder settings
- Press either Alarm 1 or Alarm 2 to stop the reminder playback when it is
- Set/Cancel/Revise the reminder schedule inside the SmartCukoo app (see app page diagram for details).
SNOOZE feature
When the reminder started, press the SNOOZE key to silent the reminder temporally. It will start again in 5 minutes by default until you actually stop the current alarm as above mentioned. (you can choose different setting inside the app).
Auto dimmer
The display intensity will automatically adjust against the environment by default, and more settings can be done inside the app.
**Smart Cukoo APP***
Your Smart phone operating system must meet the following minimum requirements: IOS: iPhone 5s and above / Android: Android 6.0 and above
You can download the SmartCukoo app from Google play or Apple store by scanning the QR code below.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF warning statement: the device has been evaluated to meet general RF exposure requirement , The device can be used in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>