Vont Innovations VNT-SP01 Smart Plug Instruction Manual
- June 6, 2024
- Vont Innovations
Table of Contents
Vont Innovations, Inc.
Instruction Manual for VONT-SP01
Item No.
| TYPE | PHOTO | DESCRIPTION |
|---|---|---|
| VNT-SP01 | | Smart Plug
Input: 120V~,50/60Hz
Output: 120V~,15A Max Resistive
Operation Temperature: 32°F~104°F (0°C~40°C)Vont Innovations, Inc.
Designed in USA. Made in China.
Conforms to UL STD 60730-1
Certified to CSA STD E60730-1FCC ID:2A3GA-VNTSP01
IC:27837-VNTSP01
-
Download apps: Download and install the Vont Home app on the App store or Google Play
-
Operation
-
Operation
3.1) Operation on/off by manual
– Press push- button ON to switch on if current mode is OFF.
– Press push-button OFF to switch off if current mode is ON
3.2) Indicator status
Product status| Network not connected| Configuring network| network
configured
successfully Socket open| network configured
successfully Socket close
---|---|---|---|---
Indicator light (blue)
status| Flash fastly| Flash slowly| Light on| Light off
3.3) Power off memory
After the product socket is turned on, the power is cut off, and the socket
will open automatically after it is powered on again;
After the product socket is closed, the power is cut off, and the socket will
close automatically after it is powered on again
-
Fault finding
a) No activation:
♦ Check setting program successful
♦ Check wifi router connection
b) No response
♦ Check if the socket has electricity, try changing it to another place
♦ Try changing a device -
Important Notes
a) DO NOT OVERLOAD.
b) To install the product needed by a qualified electrician.
-
Direction!
♦ Installation must be done by people having knowledge and experience in electrical connections
♦ Improper installation can cause danger for your own life the life of everyone using the electrial appliance
♦ Improper installation can cause damage of property e.g. fire
♦ You are personally liable for damage of property or humans -
Warning!
For your safety, please read the following cautions before installing or using your device.
♦ Do not open the device or attempt to repair or service it.
♦ Use the device in a dry location, and avoid placing it in a humid environment.
♦ Do not submerge the device in liquid or attempt to clean it with liquids or solvents. To clean the device, disconnect it from the power outlet and use a damp towel.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
MPE Requirements
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm
or more should be maintained between the antenna of this device and persons
during device operation. To ensure compliance, operations at closer than this
distance is not recommended.
Region Selection
Limited by local law regulations, version for North America does not have
region selection.
Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: —Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver. —Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. —Consult the dealer or an experienced radio/TV
technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>