AsiaRF AW7615-NP1 Dual Band 4×4 802.llac MiniPCle WiFi Module User Manual

AW7615-NP1 Dual-Band 4×4 802.lilac MiniPCle WiFi
Module

WiFi5 11ac 4T4R module 1700Mbps
Introduction

Product overview

It fully complies with IEEE802.11ac and IEEE802.11 a/b/g/n standards, offering feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance.
Optimized RF architecture and baseband algorithms provide superb performance and low power consumption. Intelligent MAC design deploys a high efficient offload engine and hardware data processing accelerators which completely offloads the Wi-Fi task of the host processor. MT7615 is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end-users the greatest performance any time and in any circumstance.
MT7615 supports concurrent dual-band operation at 5GHz and 2.4GHz band (DBDC, Dual-Band-Dual-Concurrent).
With the advent of 802.11ac, multi-user MIMO (MU-MIMO) is defined. MT7615 supports MU-MIMO with different configurations. An AP is able to use its antenna arrays to transmit multiple frames to different clients at the same time and over the same frequency spectrum.

Features:

• Supports 4×4 11ac wave2 MU-MIMO
• MU-MIMO configurations of
  • 4 users: 4*1ss
  • 3 users: 21ss + 12ss or 3*1ss
  • 2 users: 22ss or 11ss + 12ss or 21ss
• Support 80+80 channels
• Embedded ARM Cortex R4 processor for full host CPU offload
• Embedded 32-bit RISC microprocessor
• iNIC Gen2 with full Wi-Fi offload
• Highly integrated RF with 40nm low power process
• 4T4R with support of up to 1733Mbps PHY rate
• Configurable 4×4/3×3 or 2x2n+2x2ac DBDC
• Noise mitigation:
• Supports background scan function for fast channel switching
• Supports spectrum analysis for non-Wi-Fi signals
• Intelligent power saving
• Hardware-based Airtime Fairness (QoS)
• Integrate high efficiency internal 2.4G/5G PAs
• Intelligent Calibration (iCal) reduces the production time
• Supports external PA/LNA/TRSW design
• Proprietary LTE coexistence over UART
• WoWLAN via GPIO (client mode), supports Host Sleep (AP mode)
• Compact 12mm*12mm DRQFN118 package with PCIe Gen2 interface

Specification:

Data Rate

| IEEE802.11ac 1733Mbps@TX/RX
IEEE802.11a/n 600Mbps@TX/RX
IEEE802.11a/g 108Mbps
IEEE802.11b 22MbpsIEEE 802.11ac up to 1733Mbps

Output Power

| 11b: 20dbm+/- 1.5dbm @ 11Mbps
11g: 18dbm+/- 1.5dbm @ 54Mbps
11g/n: 18dBm +/- 1.5dbm @MCS7,HT20
17dBm@MCS7,HT40
11a: 16dBm +/- 1.5dbm @ 54Mbps
11a/n: 15dBm+/- 1.5dbm @MCS7,HT20
13dBm@MCS7,HT40
11ac HT20: 12+/-1.5dBm@MCS8
11ac HT40: 12+/-1.5dBm@MCS9
11ac HT80: 12+/-1.5dBm@MCS9

Receiver Sensitivity

| 11b: -89dBm@11Mbps
11g: -76dBm@54Mbps
11g/n: -74dBm@HT20,MCS7
-66dBm@HT40,MCS7
11a: -75Bm@54Mbps
11a/n: -73dBm@HT20,MCS7
-71dBm@HT40,MCS7
11ac: -57dBm+/-2dBm @HT20 MCS8
11ac: -54dBm+/-2dBm @HT40 MCS9
11ac: -51dBm+/-2dBm @HT80 MCS9
RF connector| IPEX connector

Frequency Range

| US, Canada 2.412GHz~2.462 GHz (CH1~CH11)
EU, Japan: 2.412GHz~2.472GHz (CH1~CH13)
5.150GHz~5.250GHz、5.725GHz~5.850GHz

Software

| Security: 64/128-bit WEP Encryption, WPA, WPA2
Driver: Linux
Operating Voltage| DC 3.3V ± 5%

Temperature

| Operating: 0°C ~ +70°C
Storage: -20°C ~ +90°C
Dimension| 50.95 mm (L) x 30 mm (W)

Humidity

| Operating Humidity: 10%~90% non-condensing
Storage Humidity: 10%~90% non-condensing

Mechanical Dimensions

All dimensions are in mm
Pin Define
TOP pins

Packing information

Using an antistatic tray.
One tray for 35pcs PCBA.
One carton for 23 trays=805 PCBAs

23 trays in one carton

Sealing carton

Carton label is as below:

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
The transmitter module may not be co-located with any other transmitter or antenna.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install-module.
2. This module is certified pursuant to Part 15 rules section 15.247, 15.407, and RSS-247.
3. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.
   Frequency Band| Model Number| Antenna Type| Gain(dBi)
   ---|---|---|---
   2400-2483.5MHz;

5150-5850MHz

| ANT010-DAU| PCB| 2.4GHz: 5.2

5GH: 5.5

2400-2483.5MHz;

5150-5850MHz

| A245005N| PCB| 2.4GHz: 4

5GHz: 5.1

2400-2483.5MHz| A2405N| PCB| 2.4GHz: 5.2
5150-5850MHz| A5005N| PCB| 5GHz: 5
2400-2483.5MHz;

5150-5850MHz

| A245004| Dipole| 2.4GHz: 4

5GHz: 5.1

2400-2483.5MHz;

5150-5850MHz

| A245002| Dipole| 2.4GHz: 2

5GHz: 2

4. Label and compliance information
   Label of the end product:
   FCC
   The host product must be labeled in a visible area with the following ” Contains FCC ID:
   TKZAW7615NP1″.
   The end product shall bear the following 15.19 statement: This device complies with part 15 of the
   FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
   harmful interference, and (2) this device must accept any interference received, including
   interference that may cause undesired operation.
   ISED
   This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: 9968A-AW7615NP1” or “Contains IC: 9968A-AW7615NP1”
   Content le module d’émission IC: 9968A-AW7615NP1 The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.

5. Information on test modes and additional testing requirements
   This module has been approved under a stand-alone configuration.
   OEM integrator has to be limited the operation channels in channels 1-11 for the 2.4GHz band.
   The separate approval is required for all other operating configurations, including portable
   configurations with respect to Part 2.1093/RSS-102 and different antenna configurations.
   The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
   IMPORTANT NOTE : In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization.

6. Additional testing, Part 15 Subpart B and ICES-003 disclaimer
   Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer.
   This module is only FCC/ISED authorized for the specific rule parts 15.247, 15.407/RSS-247 listed on the grant and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant.

7. The user manual of the end product should include:
   FCC:
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
   The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
   This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
   The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

ISED:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
satellites mobiles utilisant les mêmes canaux.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

www.asiarf.com
TEL: +886-2-29407880
FAX: +886-2-29407800
1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>