i-PRO WV-QDC101C Dome Cover Instruction Manual
- June 10, 2024
- i-PRO
Table of Contents
i-PRO WV-QDC101C Dome Cover
Product Information
The product is a dome cover that comes in two models, WV-QDC101C and WV-CF5SA. The WV-QDC101C model is a clear type dome cover, while the WV-CF5SA model is a smoke type dome cover with approximately 30% transmittance. The ambient operating temperature for both models is not specified, and the dimensions of the dome cover are 92 mm x 49.3 mmH with a mass of approximately 25 g (0.06 lbs). The finish of the dome cover is made of acrylic resin.
Product Usage Instructions
- Attach the enclosure fixing screw in two places to the camera.
- Fix the dustproof sheet in place with two screws. If there are any differences in the dome cover fixing method of your camera, please refer to the product information website.
- Attach the hooks to the dustproof sheet, remove one hook at a time while pushing the dome cover inwards.
- Attach the enclosure to the camera by following the installation guide of the camera.
It is important to note that the installation level for this product is lower than that of a standard clear type dome cover. After attaching the enclosure, check the settings to ensure proper installation and operation. Also, read the precautions described in the operating instructions for the camera to be attached. Lastly, i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
Operating Instructions
Included Installation Instructions
- Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
- The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
- Read also the installation guide of the camera to be used.
Dome Cover
Model No: WV-QDC101C WV-CF5SA
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
Preface
This product is the clear type dome cover.
This product is the smoke type dome cover (approx. 30 % of transmittance).
Specifications
- Ambient operating temperature : -30 °C to +50 °C {-22 °F to 122 °F}
- Dimensions: ø92 mm × 49.3 mm (H) {ø3-5/8 inches} x {1-15/16 inches} (H) Diameter of the dome : 40.1 mm {1-19/32 inches}
- Mass : Approx. 25 g {0.06 lbs}
- Finish: Acrylic resin, Clear
Smoke
Caution: Before attempting to connect or operate this product, please read these instructions carefully.
Precautions
-
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents. -
Refer installation work or dome cover replacement to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer. -
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.
Standard Accessories: Operating instructions (this document): 1 pc.
Installation
Note: When a smoke type dome cover is used, the IR LED irradiation distance and the illuminance level are lower than for a standard clear type dome cover. Check the settings after attaching the enclosure.
Step1
Step2
Note: The dome cover is locked using the enclosure hooks (3 parts). Remove one hook at a time while pushing the dome cover inwards.
Step3
Step4
Attach the enclosure to the camera by following the Installation Guide of the camera.
“<Control No.: C****>” used in these documents should be used to search for information on our technical information website (https://i-pro.com/global/en/surveillance/training-support/support/technical- information) and will guide you to the right information.
If dome cover fixing method of your camera is different from the above, please refer to the link on the following product information website. https://i-pro.com/global/en/surveillance/training-support/documentation- database-list
IMPORTANT
- When the enclosure is attached, the camera’s focus may go out of focus. Use the “Auto focus” function in the setup menu to adjust the focus.
- Remove the protective sheet after installation is complete.
- Use lens cleaning paper (used to clean camera or spectacles lenses) to remove any dirt or fingerprint on the dome cover.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>