metabo PowerMaxx KP Glue Gun Instructions
- October 27, 2023
- metabo
Table of Contents
metabo PowerMaxx KP Glue Gun
Declaration of Conformity
We, being solely responsible, hereby declare that these cordless caulking guns conform to the stand-ards and directives specified on page 3.
Specified Use
- The device is designed to extrude sealant or adhe-sive from cartridges or plastic bags.
- It is not designed for foodstuffs or for medical/veter-inary purposes. It should not be used with pressur-ized cartridges. The caulking gun should also not be used as a lifting/spreading tool.
- The user bears sole responsibility for any damage caused by improper use.
- Generally accepted accident prevention regula-tions and the enclosed safety information must be observed.
General Safety Instructions
- For your own protection and for the protection of your electrical tool, pay attention to all parts of the text that are marked with this symbol!
- WARNING – Reading the operating instruc-tions will reduce the risk of injury.
- WARNING Read all safety warnings and instructions. Failure to follow all safety warn-ings and instructions may result in electric shock, fire and/or serious injury.
- Keep all safety instructions and information for future reference.
- Pass on your electrical tool only together with these documents.
Special Safety Instructions
-
Slightly acidic, flammable fluid may leak from defective li-ion battery packs!
-
If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately.
Protect battery packs from water and mois-ture! -
Do not use faulty or deformed battery packs!
Do not expose battery packs to naked flame! -
Do not open battery packs!
-
Do not touch or short-circuit battery packs!
-
Remove the battery pack from the machine before any adjustments, conversions or servicing are performed.
-
Before fitting the battery pack, make sure that the machine is switched off.
-
Do not use frozen or set adhesive or sealant.
-
Do not overload the motor! If the motor is over-loaded, switch off the device and remove the battery pack. Determine the cause of the problem and resolve it.
-
Refer to the instructions for assembling the device. Ensure that the front cap, tube and threaded ring are correctly fitted and securely fastened.
-
Always wear protective goggles.
-
Danger of crushing! Do not take hold of the toothed rod (5)! Ensure that nothing is caught by the toothed rod.
-
Follow national requirements for the materials you want to work with.
-
Refer to the glue or adhesive manufacturers’ instructions and alsothe safety data sheet for the consumable material.
-
Adhesives and sealants can be dangerous. For this reason, you should always carefully read any instructions on the container or other information provided by the manufacturer about the material to be used. Do not use materials without knowing what risks they entail.
-
Do not use any solvent, acidic or other abrasive cleaning agents.
-
Store the device and its components in a safe place (e. g. ensure that the dismantled tube (3) is not allowed to roll away).
Overview
- Front cap
- Nozzle (for plastic bag) *
- Tube
- Threaded ring for fastening the tube
- Toothed rod
- Rod knob
- Trigger switch for switching the device on and off
- Adjusting wheel for setting feed rate
- Battery pack release button
- Battery pack
- Plastic bag *
- Screw
- Extruder plate for plastic bags
- Extrusion plate for cartridges
- Cartridge *
- not included in scope of delivery
Initial Operation
Battery pack
- Charge the battery pack before use.
- If performance diminishes, recharge the battery pack.
- The ideal storage temperature is between 10°C and 30°C.
- To remove the battery pack: Press the battery pack release button (9) and remove the battery (10) pack.
- To fit the battery pack: Slide in the battery pack (10) until it engages .
Fitting plastic bags
Attach the extruder plate for plastic bags (13) as illustrated. (To do this,
(3) unscrew the tube and then refasten it securely). See page 2, fig. A.
- Unscrew the front cap (1) from the tube (3).
- Snip the top of the nozzle (2) as required for the work to be carried out.
- Insert the plastic bag in the tube (3) (thus pushing back the toothed rod (5)).
- Trim the plastic bag (11) as recommended by the plastic bag manufacturer.
- Insert the nozzle in the front cap (2) and secure the front cap (1) tightly.
- Now gently press the rod knob (6) to advance the toothed rod until it comes in contact with the plastic bag.
Fitting the cartridge
Remove the extruder plate for plastic bags (13) as illustrated. (To do this,
(3) unscrew the tube and then refasten it securely). See page 2, fig. B.
- Unscrew the front cap (1) from the tube (3).
- Open the cartridge (15) as per the cartridge manufacturer’s instructions.
- Snip the top of the cartridge nozzle as required for the work to be carried out.
- Now insert the cartridge (15), with the attached cartridge nozzle, into the tube (3) (thus pushing back the rod (5)).
- Screw on the front cap (1) tightly.
- Now gently press the rod knob (6) to advance the toothed rod until it comes in contact with the cartridge.
Use
Multifunctional monitoring system
If the device switches off automatically, the machine electronics have activated automatic protection mode.
Causes and remedies:
-
Battery pack almost flat (the electronics prevent the battery pack from discharging totally and avoid irreparable damage).
If the battery pack is almost flat, it must be recharged. -
Long continuous overloading of the machine will activate the temperature cut-out.
Leave the machine or battery pack to cool. -
If the current is too high (for example, during extended periods of overloading) the device is switched off.
Using the trigger switch, turn off the device (7) and remove the battery pack. Determine the cause of the problem and resolve it.
Setting the feed rate
Set the feed rate using the adjusting wheel (8).
Switching on and off
- Switching on: press the trigger switch (7).
- Switching off: release the trigger (7). Note: The toothed rod is automatically retracted slightly to avoid dripping.
Note: The motor switches off automatically if either the cartridge or the plastic bag is empty.
Accessories
Use only genuine Metabo accessories.
Conversion kit 400 ml Order no.: 6.30148 Comprising a short toothed rod (5)
and 400 ml tube (3) for replacing parts. See page 2, fig. C.
- Unscrew the tube (3).
- Extract the screw from the rod knob (6) and pull the rod knob back from (6) the rod (5).
- Pull the toothed rod forwards from the motor housing.
- Extract the screw and dismantle the components (12) to (14) from the rod.
- Insert the rod from the conversion kit towards the front.
- Attach the rod knob (6) on top and fasten it in place with a screw.
- Fit components (12) to (14) on the other rod and fasten in place with a screw.
- Screw the tube from the conversion kit together tightly.
For a complete range of accessories, see www.metabo.com or the accessories catalogue.
Repairs
- Repairs to electrical tools must be carried out by qualified electricians ONLY!
- If you have Metabo electrical tools that require repairs, please contact your Metabo service centre. For addresses see www.metabo.com.
- You can download spare parts lists from www.metabo.com.
Environmental Protection
- Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.
- Battery packs must not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer!
- Do not allow battery packs to come into contact with water!
- Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Guideline 2002/96/EC on used electronic and electric equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling. Before disposal, discharge the battery pack in the power tool. Prevent the contacts from short-circuiting (e. g. by protecting them with adhesive tape).
Technical Specifications
- Explanatory notes on the specifications on page 3.
- Changes due to technological progress reserved.
- U = Voltage of battery pack
- v = Feed rate
- F = Extrusion force
- m = Weight (with smallest battery pack)
- Measured values determined in conformity with EN 60745.
- Direct current
- The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).
Emission values
Using these values, you can estimate the emissions from this power tool and
compare these with the values emitted by other power tools. The actual values
may be higher or lower, depending on the particular application and the
condition of the tool or power tool. In estimating the values, you should also
include work breaks and periods of low
use. Based on the estimated emission values, specify protective measures for
the user – for example, any organisational steps that must be put in place.
Vibration total value (vector sum of three directions) determined in
accordance with EN 60745:
- ah =Vibration emission level
- Kh = Uncertainty (vibration)
- Typical A-effective perceived sound levels:
- LpA =Sound pressure level
- LWA =Acoustic power level
- KpA, KWA= Uncertainty
Wear ear protectors!
Documents / Resources
|
metabo PowerMaxx KP Glue
Gun
[pdf] Instructions
PowerMaxx KP Glue Gun, PowerMaxx KP, PowerMaxx KP Gun, PowerMaxx Glue Gun, KP
Glue Gun, Glue Gun
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>