vtech VM5263-2 Full Color Pan and Tilt Video Monitor User Guide
- June 6, 2024
- vtech
Table of Contents
VM5263-2 Full Color Pan and Tilt Video Monitor
Technical specifications
Crystal controlled PLL synthesizer
Baby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz
(WQVGA 480×272 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.
Parent unit: 3.8V Li-ion battery Baby unit power adapter: Output: 5V DC @ 1A Parent unit power adapter: Output: 5V DC @ 1A
Credits: The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.
Go to www.vtechphones.com to register your product for enhanced warranty
support and the latest VTech product news.
Quick start guide
Specifications are subject to change without notice. © 2021 VTech Communications, Inc. All rights reserved. 02/21. VM5263-X_QSG_V4.
5″ Color LCD
32
VM5263 VM5263-2
Full Color Pan and Tilt Video Monitor
For more support information:
S m
VM5263
VM5263-2
Frequency control
Transmit frequency
Power requirements
Channels
LCD
Important safety instructions
The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
- Follow all warnings and instructions marked on the
product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above
2 meters. 4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used as such. 5. This product is not intended for use as a medical monitor. 6. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 7. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC® seal. 8. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Power adapter information: Parent unit output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EUS05100 Baby unit output: 5V DC 1A. VTech Telecommunications Ltd. Model: VT05EUS05100
Rechargeable battery information: Li-ion battery, 3.8V 2100mAh Zhongshan Tianmao Battery Co., Ltd. Model Number: BP1763 9. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 10. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 11. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15. Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.
18. Never push objects of any kind into this product through the slots
because they may touch dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not disassemble this product,
but take it to an authorized service facility. Opening or removing parts of
the product other than specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause electric shock when
the product is subsequently used.
20. You should test the sound reception every time you turn on the units or
move one of the components.
21. Periodically examine all components for damage. 22. There is a very low
risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless telephones, etc. To
protect your privacy, make sure the product has never been used before
purchase, reset the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor if you will not use it
for some time. 23. Children should be supervised to ensure that they do not
play with the product. 24. The product is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
SAVE THESE INSTRUCTIONS
Cautions 1. Use and store the product at a temperature between 32oF
and 104oF. 2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source. 3. Batteries
should not be exposed to excessive heat such as
bright sunshine or fire.
Warning–Strangulation Hazard–
Children have STRANGLED in cords. Keep
this cord out of the reach of children
(more than 3 ft (0.9m) away). Do not
remove this tag.
5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients · Should keep wireless devices at least six inches from the
pacemaker. · Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation
did not identify any risk to bystanders with pacemakers from other persons
using wireless devices.
Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.
Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three
feet away from the child at all times. Do not use with an extension cord. Do
not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se
trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez
pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños.
Este cable debe estar por lo menos tres pies fuera de la alcance del niño en
todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.
Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three
feet away from the child at all times. Do not use with an extension cord. Do
not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se
trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez
pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños.
Este cable debe estar por lo menos tres pies fuera de la alcance del niño en
todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.
What’s in the box
KTeaheuepwrstaceeyhoirmfswridotcovnÉhoelmrectaotediophnirhdigNoed’ssceenudoutetxetctsttainoztlheoiigdefcl.d’bsnerduoseéeiitezMcntiaadolaattoqspeencrolneualdantdhleccfsetleoeloartmaoeosottdsrnisefonnnntetentidg.nui.ctdamruañvoeñheehatinseoeDlreslsoltr.atsicoseed.oretàerqee,nDenennEexfuafstosogteceneatuto.eetpna.neenidatnttbo.emlscsNotois.eoaeiufóLfbtrmnluneuetsoieeteertirnrrmdaaameoeleidzpádnsbeste.eplmol.aaebassrNaitallcoaccral.aaopnnNcoucroeseequite StranHgadzu’laéatrtrRidiasoneqnsgultRrieeaemsneggnoutldaeción KTeaheuepwrstaceeyhoirmfswridotcovnÉhoelmrectaotediophnirhdigNoed’ssceenudouttexetctsttainoztlheoiigdefcl.d’bsnerdsuoeéeiitezMcntiaadolatatoqspeencrolneuaaldnthdleccfsteleoelaortmoaeosottdsrnifesonnnntetentidg.nui.ctdamruañvoeñheehatinseeoDlreslsoltr.atsiocseed.oretàerqee,DnenennEexfuafstoosgteceneattu.oeetpnan.eneidtanttbo.emlcssNotois.eoaeiufóLfbtrmnluneuetsoieeteertirnrrmdaaameoeleidzpádnsbeste.eplmol.aaebassrNaitallcoaccral.aaopnnNcoucroeseequite StranHgadzu’laéatrtrRidiasoneqnsgultRireeaemsneggnoutldaeción
Quick start guide
x 2
x 2
1 set for VM5263 2 sets for VM5263-2
1 Connect the baby monitor
NOTES · The rechargeable battery in the parent unit is built-in. · Use only
the power adapters supplied with this product. · Make sure the baby monitor is
not connected to a switch-controlled electric outlet. · Connect the power
adapters in a vertical or floor mount position only. The adapters’ prongs are
not
designed to hold the weight of baby monitor, so do not connect them to any
ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not
properly connect to the outlets. · Make sure the parent unit, the baby units
and the power adapter cords are out of reach of children.
2 Power on or off the baby monitor
Slide the switch to power on or off your baby unit.
Power on Power off
Press and hold POWER to power on or off your parent unit.
Power on
Long press
Power off
Long press
3 Positioning the baby monitor
3ft (1m)
4 Status check
Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. The ON LED light of baby unit turns on.
63
3ft (1m)
< 3ft (1m)
63
Caution
· The default volume of your parent unit is level 4, and the maximum volume is
level 7. If you experience high-pitched screeching noise from your baby
monitor while positioning: – Make sure your baby unit and parent unit are more
than 3 feet (1 meter) apart, OR – Lower the volume of your parent unit.
63
3ft (1m)
< 3ft (1m)
Note
· To avoid interference from other electronic devices, place your baby monitor
at least 3 feet (1 meter) away from devices such as wireless routers,
microwaves, cell phones and computers.
CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1
Basic operation – Parent unit
Adjust speaker volume
Press / to adjust your parent unit speaker volume.
Zoom
Press to zoom in or out.
77 77
Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted
to the baby unit. Release TALK when finish talking and hear your baby again.
Turn off the screen
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound
from the baby unit.
77
Press and hold
Long press
Tip
· Press any keys on the parent unit to turn on the screen again.
Use the menu
Press to enter the menu, choose a menu item, or save a setting. You can use
the parent unit for advanced settings or operations, such as to play or stop
the baby unit lullaby, or to adjust the baby unit sound sensitivity. While in
the menu:
77
· Press or to scroll among the menu options. · Press to select an item, or to
save a setting. · Press or to scroll among the sub-menus,
or to adjust a setting. · Press to return to the previous menu options
without changing the current setting. · Press /EXIT to return to live video.
Overview – Parent unit
1 2
1 LED lights 2 LCD display 3 Microphone 4 POWER 5 TALK
11
3
4
12
5
6
7
8
13
9
10
6 MENU/SELECT
7 Arrow keys
8
Volume
9 VIEW /LCD ON/OFF
10
/EXIT
11 Antenna
12 RESET
13 Stand
14 Power jack
Overview – Baby unit
1
2
3
7
10
5
6
8
4
9
1 Light sensor 2 Camera lens 3 Microphone 4 Night light 5 On/Off switch
6 On/Off LED light · On when the baby unit is turned on and is paired to the
parent unit. · Flashes when the baby unit is not being viewed; or when the
link to the parent unit is lost.
7 Speaker
8
Night light on/off key
9 Power jack
10 Slots for wall mounting
Need help?
For operations and guides to help you using your video monitor,
14
and for latest information and supports, go and check the online
S
help topics and online FAQs.
m
Use your smartphone or mobile device to access our online help.
· Go to https://help.vtechphones.com/vm5263 or
https://help.vtechphones.com/vm5263-2; OR
· Scan the QR code on the right. Launch the camera app or QR code scanner app
on your smartphone or tablet. Hold the device’s camera up to the QR code and
frame it. Tap the notification to trigger the redirection of the online help.
VM5263
– If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.
You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.
VM5263-2
Parent unit icons
Main menu icons
Main menu
Sub-menu
Brightness
· Adjust the parent unit’s LCD brightness.
Camera settings
Lullaby /
Baby unit speaker volume · Adjust the baby unit’s speaker
volume. Monitoring mode (For VM5263-2 only)
· Single mode · Split mode · Patrol mode
Play/Stop lullaby
· Select one of the soothing sounds, or white noise.
· Select one of the five melodies. · Play all melodies. · Set timer to stop
playing the selected
melody or soothing sound.
Main menu
Sub-menu
Night light
/
Turn on/off night light
4 5 6 7
· Select one of the night light colors.
· Change to all seven colors in cycles. · Set timer to turn the night light off. · Select to set the night light to always on.
Main menu
Sub-menu
Alert tones
· Set the parent unit to beep when the battery is low.
· Set the parent unit to beep when the link between the parent unit and the
baby unit is lost.
· Set the confirmation tone on or off when selecting an option in the menus.
· Set the parent unit to beep when the baby unit detects sounds while in Split mode (For VM5263-2 only).
A
Temperature
· Set to auto turn on the night light when baby unit detects sound. It will
turn off after 15 minutes of no sound detection. You can set VOX sensitivity
level to detect sounds that exceed certain levels. See Sound sensitivity and
sound activation section. /
· Turn on/off the adaptive night light feature. When this feature is on, the
baby unit detects the ambience light. If the room is bright, the night light
adjusts itself to be brighter; if the room is dim, the night light adjusts
itself to be less bright.
/ · Turn on/off temperature alert tone. · Set the parent unit to beeps
whenever
the room temperature detected by the baby unit falls outside of the set
temperature range. · Set the minimum temperature.
· Set the maximum temperature.
Sound activation – screen and audio
/
Turn on/off sound activation
· Set sound activation on or off. · When it is on, and the baby unit detects
no sound, the parent unit screen stays off to save power. Once a sound is
detected, the parent unit screen and speaker turns on automatically, and you
can see and hear your baby. The parent unit will then turn off again after 50
seconds of no sound detection.
Note
· When the parent unit screen is off and it receives alerts, for example, link
lost between parent unit and baby unit, or battery is low, the parent unit
screen and speaker will turn on for 10 seconds.
VOX (Voice Activated Alert) Sensitivity
· You can set VOX sensitivity level to activate parent unit screen and sound
when baby unit detects sounds that exceed certain levels. See Sound
sensitivity and sound activation section.
· Set temperature display in Fahrenheit (oF) or Celsius (oC)
Parent unit icons (Cont’d)
Status icons
Connection status
·
– Strong signal strength.
· – Moderate signal strength.
· – Low signal strength.
· – Weak signal strength.
Split mode (For VM5263-2 only)
Patrol mode (For VM5263-2 only)
or Current view status · The baby unit number that is being viewed when in:
– Single CAM mode. – Patrol mode
(For VM5263-2 only) – Split mode
(For VM5263-2 only)
Night vision – On
Zoom – On
Lullaby – On
Night light – On
Night light – Auto-on · Color icon indicates the night
light is set to auto-on, and is currently turned on by sound activation. ·
Gray icon indicates the night light is currently off but is set to auto-on.
Night light will turn on when sound is detected by the baby unit.
Status icons
oF or oC
Real-time temperature · Real-time temperature
detected by the baby unit in Fahrenheit (oF) or Celsius (oC) (e.g. 57 oF or 14
oC).
Temperature alert tone – On
9-level sound indicator ·
indicates low sound level detected by the baby unit. · indicates moderate
sound level detected by the baby unit. · indicates high sound level detected
by the baby unit.
Mute alert · Displays when the parent unit
speaker volume is set to off. · Displays when the parent unit
is talking to the baby unit.
Battery status
·
animates
when the battery is charging.
·
– battery is fully charged.
· – battery is low and needs charging.
Alert icons
· Displays when parent unit’s battery is low and needs charging.
· Displays when connection between parent unit and baby unit is lost. ·
Displays when sound is detected at a baby unit when in Split view.
(*For VM5263-2 only) · Baby unit detects temperature reaches or exceeds the
set maximum.
· Baby unit detects temperature is at or is lower than the set minimum.
Mount the baby unit on dry wall (optional)
Notes
· Check for reception strength and camera angle before drilling the holes.
· The types of screws and anchors you need depend on the composition of the
wall. You may need to purchase the screws and anchors separately to mount your
camera units.
1. Place the wall mount bracket on a wall and then use a pencil to mark two holes in parallel. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).
2. If you drill the holes into a stud, go to step 3.
· If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the wall
anchors are flush with the wall.
3. Align the wall mount bracket and screws with the holes in the wall as
shown. Tighten the screw in the middle hole first, so that the wall mount
bracket position is fixed. You can tighten the other screw in the top hole.
4. Place the camera unit on the wall mount bracket, and then slide it forward
until it locks into place. Connect the power adapter to the camera unit and a
power supply not controlled by a wall switch.
3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.
OR
4. Place the camera unit on the wall
mount bracket, and then slide it
forward until it locks into place. Align
the holes on the wall mount bracket
with the screws on the wall, and slide
the wall mount bracket down until it
locks into place.
2 1
5. You can maximize your camera unit’s viewing angles by tilting the wall mount bracket. Hold the camera unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.
Sound sensitivity and sound activation
Adjust sound detection sensitivity
You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn on the parent unit while its screen is switched off or dimmed. When the baby unit detects sounds that exceed certain levels, the parent unit screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and you can see and hear your baby. If you have turned on the Night light Auto-on feature, it will turn on automatically to sooth your baby. If you turn off Sound activation, you will hear sounds from the baby unit all the time, even when the parent unit screen is switched off. If you have turned on sound alert, the parent unit beeps when the baby unit detect sounds while in Split mode (*For VM5263-2 only).
VOX Sensitivity level
Level 5 (Highest)
Level 4 (High)
Level 3 (Medium)
Level 2 (Low)
Description
(Default setting)
The parent unit screen and speaker turn on for very small sounds, including
background noises from your baby’s room.
The parent unit screen and speaker turn on for soft babbling and louder sounds from your baby. The parent unit remains quiet when your baby sleeps soundly.
The parent unit screen and speaker turns on for loud babbling and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.
The parent unit screen and speaker turn on for crying and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.
Level 1 (Lowest)
The parent unit screen and speaker turn on for loud crying or screeching
sounds from your baby. The parent unit remains quiet when your baby makes soft
sounds.
Sound activated screen and audio
When Sound activation is on, the parent unit screen stays off to save power
when the baby unit detects no sound. Once the baby unit detects sounds that
are louder than the chosen sound sensitivity level, the parent unit screen and
speaker turn on automatically. The parent unit will then turn off again after
50 seconds of no sound detection.
Note
· If you have muted the parent unit speaker, only the parent unit screen will
turn on when a sound is detected.
Night vision
The baby unit has infrared LEDs that allow you to see your baby clearly at
night or in a dark room. When the baby unit being viewed detects low light
levels, the infrared LEDs are switched on automatically. The images from the
baby unit are in black and white, and appears on the screen.
Notes
· It is normal if you see a short white glare on your parent unit screen as
the baby unit is adapting to the dark environment.
· When the infrared LEDs are on, the images are in black and white. This is
normal.
Tip
· Depending on the surroundings and other interfering factors, like lightings,
objects, colors and backgrounds, the video quality may vary. Adjust the baby
unit’s angle or place the baby unit at a higher level to prevent glare and
blurry display.
Dim mode
The parent unit display will dim to conserve energy after 10 minutes of
inactivity, in which there is neither key pressed nor alert received from the
baby unit.
10 min inactivity Press any buttons
For VM5263-2 only
Status check – Two baby units
If you are viewing baby unit , the
POWER LED light of baby unit
turns on. As baby unit
is not being
viewed, its POWER LED light flashes.
Notes
· If you power on only one baby unit, you may see the parent unit displaying the LINK LED light flashing.
and then
· Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.
, and
Change different views – Single CAM
In Single CAM or
Patrol mode, press
VIEW to switch
between the image
77
of baby units
and .
Press VIEW
Change different views – Patrol
Change different views – Split
Select Patrol as your monitoring mode to
alternately view the image from baby units
and
every 10 seconds.
77
10s
Select Split as your monitoring mode to view the images from both baby units
at once.
77
The RBRC seal
The RBRC seal on the lithium-ion battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry program to collect and
recycle these batteries at the end of their useful lives, when taken out of
service within the United States and Canada. The program provides a convenient
alternative to placing used lithium-ion batteries into the trash or municipal
waste, which may be illegal in your area. VTech’s participation makes it easy
for you to drop off the spent battery at local retailers participating in the
program or at authorized VTech product service centers. Please call 1 (800) 8
BATTERY® for information on lithium-ion battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in this program is part of
its commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of
Call2recycle, Inc.
FCC and IC regulations
FCC Part 15 This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements are intended to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: · Reorient or relocate the receiving antenna. · Increase
the separation between the equipment and receiver. · Connect the equipment
into an outlet on a circuit different from that to which the receiver is
connected. · Consult the dealer or an experienced radio/TV technician for
help. WARNING: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This device complies with Part 15 of the
FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed by a user or
bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The baby unit shall be
installed and used such that parts of all persons’ body are maintained at a
distance of approximately 8 in (20 cm) or more. The transmitter and antenna of
the parent unit shall be held at least 1 in (2.5 cm) from your face. This
Class B digital apparatus complies with Canadian requirement: CAN ICES-3
(B)/NMB-3(B)
Industry Canada This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of the
device. The term ’IC:’ before the certification/registration number only
signifies that the Industry Canada technical specifications were met. This
product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
RF radiation exposure statement The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. The baby unit
should be installed and operated with a minimum distance of 8 in (20 cm)
between the baby unit and all persons’ body. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. This equipment complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for
energy consumption. Your baby monitor is set up to comply with the energy-
conserving standards right out of the box. Follow the instructions to install
and charge the battery. The CEC battery charging testing mode is activated
while charging. Even if the parent unit is paired to baby units, the CEC
battery charging testing mode is activated while it is powered off and
charging.
For cETL compliance only
Mesures de sécurité importantes La plaque signalétique appliquée est située au
bas du socle de l’unité du bébé. Lorsque vous utilisez votre appareil, vous
devriez toujours suivre certaines mesures de précaution de base afin de
réduire les risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent : 1. Observez toutes les instructions et mises en garde
inscrites sur
l’appareil. 2. L’installation par un adulte est requise. 3. MISE EN GARDE:
N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres. 4. Ce produit a été conçu pour être un dispositif
d’appoint
seulement. Il n’est pas le remplacement d’une supervision responsable et
adéquate par un adulte et ne devrait pas être utilisé comme telle. 5. Ce
produit n’est pas conçu pour être utilisé en tant que moniteur médical. 6.
N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité,
par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un
sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.
7. MISE EN GARDE: Utilisez uniquement la pile fournie. Il se peut qu’il y ait
un risque d’explosion si un mauvais type de pile est utilisé pour l’unité du
parent. La pile ne peut pas être soumise à des températures extrêmes et la
basse pression atmosphérique à haute altitude pendant l’utilisation,
l’entreposage ou le transport. Élimination de la pile dans le feu ou dans un
four chaud, ou en écrasant ou en coupant mécaniquement ou la pile peut
provoquer une explosion. Laisser la pile en un environnement à température
extrêmement élevée peut entraîner une explosion ou une fuite de liquide
inflammable de gaz. Une pile soumise à une pression d’air extrêmement basse
peut provoquer une explosion ou une fuite de liquide inflammable ou du gaz.
Éliminer la pile usagée conformément aux informations figurant dans le sceau
RBRC. 8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation
d’un adaptateur dont la polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques : Adaptateur de l’unité du parent
: Sortie : 5V CC 1A VTech Telecommunications Ltd. Modèle : VT05EUS05100
Adaptateur de l’unité du bébé : Sortie : 5V CC 1A VTech Telecommunications
Ltd. Modèle : VT05EUS05100
Informations sur les piles rechargeables : Li-ion battery, 3.8V 2100mAh
Zhongshan Tianmao Battery Co., Ltd. Model Number: BP1763 9. Lorsqu’ils sont
branchés dans une prise de courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la verticale ou au plancher. Les
broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation
et le maintenir en place si celuici est branché dans une prise au plafond,
sous une table ou dans un meuble. 10. Pour les PRODUITS À BRANCHER À UNE PRISE
DE COURANT, la prise de courant doit être installée près du produit, afin
d’assurer une accessibilité sécuritaire à la prise de courant. 11. Débranchez
ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez
pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer.
12. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car
ceci peut présenter un danger potentiel. 13. Ne laissez aucun objet reposer ni
appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un
endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué
sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous
possédez à votre domicile, consultez votre marchand ou votre compagnie locale
d’électricité. 15. Ne surchargez pas les prises de courant murales ni les
rallonges électriques. 16. Ne placez pas cet appareil sur un chariot, meuble,
trépied, support de montage ni table chancelants. 17. Les trous et ouvertures
du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer
l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces
ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant
sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un
calorifère. De plus, ne placez
pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne
circulation d’air. 18. N’enfoncez jamais d’objets à travers les ouvertures de
cet appareil, car ils pourraient entrer en contact avec des points de tension
dangereux ou causer des courtscircuits qui peuvent dégénérer en incendies ou
en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.
19. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil,
mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou
le retrait de toutes pièces que contient cet appareil, à l’exception de
l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un remontage incorrect
peut par la suite présenter des risques d’électrocution. 20. Vous devriez
tester la réception chaque fois que vous mettez l’appareil en fonction. 21.
Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées. 22. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés, téléphones sans
fils etc.). Pour l’éviter, s’assurer que le produit n’a jamais été utilisé
avant l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-
bébé quand il n’est pas en cours d’utilisation. 23. Les enfants devraient être
supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil. 24. Le
produit n’est pas conçu pour être utilisé par des personnes (incluant des
enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui
manquent d’expérience et de connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit
à une température entre 0° C
(32°F) et 40°C (104° F). 2. N’exposez pas cet appareil à des froids ou des
chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près
d’une source de chauffage. 3. Le bloc-piles ne doit pas être exposé à la
chaleur excessive telle que la lumière du soleil ou au feu.
Avertissement – Risque de strangulation
– Les enfants se sont ÉTRANGLÉS dans des
cordons. Gardez ce cordon hors de portée des
enfants (à plus de 0,9 m). N’enlevez pas cette
étiquette.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du
parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)
portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des
appareils électroniques tels que des routeurs sans fil, radios,
téléphones cellulaires, interphones, moniteurs, téléphones,
ordinateurs personnels, électroménagers et téléphones sans
fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme `Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
· Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
· Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF) Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.
Limited warranty
What does this limited warranty cover? The manufacturer of this VTech Product
warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that
the Product and all accessories provided in the sales package (“Product”) are
free from defects in material and workmanship, pursuant to the following terms
and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective
Product”)? During the limited warranty period, VTech’s authorized service
representative will repair or replace at VTech’s option, without charge, a
Materially Defective Product. If we repair the Product, we may use new or
refurbished replacement parts. If we choose to replace the Product, we may
replace it with a new or refurbished Product of the same or similar design. We
will retain defective parts, modules, or equipment. Repair or replacement of
the Product, at VTech’s option, is your exclusive remedy. VTech will return
the repaired or replacement Products to you in working condition. You should
expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period? The limited warranty period for the
Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the date the repaired or
replacement Product is shipped to you or (b) the time remaining on the
original one-year warranty; whichever is longer.
What is not covered by this limited warranty? This limited warranty does not
cover: 1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation, abnormal operation
or handling, neglect, inundation, fire, water or other liquid intrusion; or 2.
Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech; or 3. Product
to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems; or 4. Product to the extent
that the problem is caused by use with non-VTech accessories; or 5. Product
whose warranty/quality stickers, product serial number plates or electronic
serial numbers have been removed, altered or rendered illegible; or 6. Product
purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes); or 7.
Product returned without a valid proof of purchase (see item 2 below); or 8.
Charges for installation or set up, adjustment of customer controls, and
installation or repair of systems outside the unit.
How do you get warranty service? To obtain warranty service in the USA, please
visit our website at www.vtechphones.com or call 1
800-595-9511. In Canada, go to
www.vtechcanada.com or call 1
800-267-7377. NOTE: Before calling for
service, please review the user’s manual – a check of the Product’s controls
and features may save you a service call. Except as provided by applicable
law, you assume the risk of loss or damage during transit and transportation
and are responsible for delivery or handling charges incurred in the transport
of the Product(s) to the service location. VTech will return repaired or
replaced Product under this limited warranty. Transportation, delivery or
handling charges are prepaid. VTech assumes no risk for damage or loss of the
Product in transit. If the Product failure is not covered by this limited
warranty, or proof of purchase does not meet the terms of this limited
warranty, VTech will notify you and will request that you authorize the cost
of repair prior to any further repair activity. You must pay for the cost of
repair and return shipping costs for the repair of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty service? 1. Return the
entire original package and contents including
the Product to the VTech service location along with a description of the
malfunction or difficulty; and 2. Include a “valid proof of purchase” (sales
receipt) identifying the Product purchased (Product model) and the date of
purchase or receipt; and 3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or oral communications
related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding
the Product. There are no other express warranties. No one is authorized to
make modifications to this limited warranty and you should not rely on any
such modification. State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other rights, which vary from
state to state or province to province. Limitations: Implied warranties,
including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to
one year from the date of purchase. Some states/ provinces do not allow
limitations on how long an implied warranty lasts, so the above limitation may
not apply to you. In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including, but not limited to
lost profits or revenue, inability to use the Product or other associated
equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>