Nutek 22870433 MTVA Car Alarm Transmitter Instruction Manual
- June 6, 2024
- Nutek
Table of Contents
22870433
MANUAL
-
Power On Status: All functions Off
-
Learn-in Code:
-
Turn IGNITION OFF to ON (open for 15 seconds)
-
Press VALET SW.OFF/ON 3 times, LED ON turned on, and activate learn-in-Code MODE.
2.1 Press Btn”1” to learn the first TX.
2.2 —- Horn 20ms, one Beep, Press LED OFF/ON once.
2.3 Other Keys automatically activated.
2.4 Back to 2.2.1 learn the next TX, up to 4 TX codes. -
Turn IGN ON to OFF, or 15seconds time-out, ending the learn-in-code process: LED OFF
-
Common TX function
TX BUTTON
| FUNCTION|
REMARK
---|---|---
| Lock Door| Horn 1 Chirp(2 times/3sec ,20ms) P/L 1 flashing, D/HT Dimming .
| Unlock Door| P/L 2 flashing, D/HT On, Dimming after 30 seconds
| 2-Step Unlock| Press 2 times in 3seconds
| Silent Lock / Unlock / DUL#2| Press 2 keys at the same time
AUX
| 0.5 sec Trunk (CH#2)| 0.5sec On / 0.5sec Off (Exit Light)
| 3 sec PANIC (0.3″On/0.75–0ff)| Horn Chirping, P/L flashing 60sec, without
D/L, D/UL, with CH#2
7. D/HT Function: Dimming Time 5 sec4. FEATURE PROGRAM: ★★: RED part is Default Setting
4.1 IGN OFF TO ON (open for 15 Sec), VALET SW ON/OFF(6 times), finished in 15
Sec.
4.2 Chirp 6 Beep, LED ON, proceed Setup, as below circumstance
4.3 IGN OFF shutdown FEATURE Mode, Horn Chirp 1 short-sound 1long-sound
4.4 FEATURE TABLE
Press TX Btn X
| One Chirp, LED 0.3| 2 Chirps, LED 0.3 – 2 pulse| 3 Chirps, LED 0.3 – 3 pulse|
4 Chirps, LED 0.3 – 4 pulse
---|---|---|---|---
| In “On” TX activates| Ig n “On” TX No function| If I”On”(AUX, PANIC)
| Rearm Off| Rearm On| |
AUX
| Exit Light On 3 minutes| Exit Light On 5 minutes| Exit Light On 10 minutes|
Exit Light On 15 minutes
| 5 Chirps, LED 0.3 – 5 pulse| Exit Light On 20 minutes| |
8. D/HT Function: Dimming Time 5 sec
5 -1. Door Open / Close = D/HT On 20 sec, then Dimming .
5 -2. Remote Door Unlock = D/HT On 30 sec, then Dimming.
5 -3. Ext Car Remote Lock The Door then Dimming
5-4. Sign On D/HT Off then Dimming
GOVERNMENT REGULATIONS
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.