APEX Set Inbound/Outbound Volumes User Guide
- June 6, 2024
- Apex
Table of Contents
SET INBOUND/OUTBOUND VOLUMES
- After login in, press the Volume icon
- To enable/disable nighttime outbound volume press to enable or disable. Then select the time to start and stop. Note: This reduces outbound audio by 20%
- Adjusting kitchen speaker volume for Lane 1 or Lane 2 Note: Press the circle and slide left or right to the appropriate volume level
- Adjusting the outbound speaker for Lane 1 or Lane 2 Note: Press the circle and slide left or right to the appropriate volume level
- Adjusting the inbound microphone for Lane 1 or Lane 2 Note: Press the circle and slide left or right to the appropriate volume level
NOISE SUPPRESSION
- After logging in, press the Audio icon
- Adjust the amount of Noise Suppression for the outside speaker Note: Press the circle and slide left or right to adjust to proper settings
- Adjust the amount of Noise Suppression on the inbound microphone Note: Press the circle and slide left or right to adjust to proper settings
- Extended sitting and Echo cancellation
Note: Please call support at 800.598.2370 when adjusting these settings
LANE SETTINGS
- After logging in, press the Lane icon
- Singl Lane Set Speed Team and Override Lane 1
- Dual Lane Configuration Note: Headsets will need to be either Team 1 or Team 2
- Speed Team or Vehicle Override Note: Press the slider to turn on Speed Team for Lane 1 or Lane 2. Press the slider to turn on Vehicle Override for Lane 1 or Lane 2
MANAGER
- After logging in, press the Manager icon
- Set the time and change the manager password Note: Follow the onscreen prompts to change time and the manager’s password
IMPORT/EXPORT AND ENGINEER SETTINGS
Note: Call R.F. Technologies, Inc. at 800.598.2370 to get into these settings.
HELP ICON
Note: For questions on how to:
- Set Alerts
- Set Reminders
- Set Greeters
- Set Volumes
- Register Headsets
- Select a Lane Type
FCC Regulation
Headset
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense
Base Station
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: This device may not cause harmful interference. This device must
accept any interference received, including interference that may cause
undesired operation of the device.
In order to comply with FCC and IC RF Exposure requirements, the base must be
installed and operated such that a minimum separation distance of 20 cm is
maintained between the base and all persons during normal operation
Changes or modifications not expressly approved by R.F. Technologies, Inc.
could void the user’s authority to operate this equipment.
Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s)].
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Ready for APEX to provide your customers with their best drive-thru
experience?
Contact us today.
rfdrivethru.com
|800-598-2370|sales@rftechno.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>